Building A Custom 1 of 1 E91 M3 Wagon! (Part.16)

Nour Hummadi
114 followers
4 Video Views·Nov 5, 2022
SMASH THAT LIKE BUTTON TO GET THE ENGINE IN NEXT VIDEO!
●My Ebay Store: https://www.ebay.com/usr/nadiandcompany?_trksid=p2047675.m3561.l2559
● Merch: https://NADIPERFORMANCE.com
● Follow me on Instagram: https://www.instagram.com/nour_hummadi/
----------------------------------------------------------
SPONSORS! (CODE)
KiesMotorsports (NOUR5)
SimplyCarbonFiber (NOUR10)
BurgerTuning
FCP EURO
AzaAutoWheel
Suvneer
SSR Performance
Valvetronic (NOUR)
RoughCountry
----------------------------------------------------------
Today's November 5th and I'm filming the intro to this ridiculous video.
About five days ago I decided, you know what, let's go ahead and remove the harness completely
out of our E90 and transfer it over our E91 and hopefully figure out a way to get everything
routed.
Now honestly, it wasn't that difficult up until we got to the trunk area, which we haven't
done yet mainly because we do a lot of custom wiring, but for the meantime, to get this
bad boy running and driving and everything, we got everything prepped up in this one video
and I decided instead of dragging it out to be 30 minutes to show you guys all the
little, you know, the NC little things, I was like, you know what, let me go ahead and
just make it five minutes.
So you guys can see all the hard work done in the last like four or five days in five
minutes.
And this is one of those videos that's like, uh, it doesn't look like a lot got done, but
a lot got done guys.
The wiring harness is what connects all the modules, what pretty much powers everything
in the entire car.
So the fact that we got mostly everything routed, um, you guys about to see how cool
this is going to look.
Now for the next couple of minutes, you guys are not going to hear my voice.
For some of you guys, you're going to love it for some of you guys are going to hate
it.
Well, it is what it is.
And guys, after countless of hours of nonstop work, I am happy to say we pretty much got
the harness routed exactly the way it's supposed to be.
We literally have all the phone pieces, all this tabs, everything connected properly.
You guys can see all the wiring, the grounds, the fuse box, everything's connected.
This belongs to the airbag.
I went ahead and literally checked every single wire, what it all connects to.
I mean, for the most part, I do know what I'm doing.
This cage is fully connected in this point.
So technically we could throw in the dashboard.
All these wires over here are routed.
All of this is routed.
We went ahead and put the foam stuff back over there.
Same on that side and same on this side.
I'm not going to lie, guys, we have come such a long way with this car and this is not the
E91 harness.
This is the E91 M3 harness is so far up to this point.
Everything is the same.
Thankfully, the last thing I need to do to complete the rear seats wiring to the front
of the car is just connect the rear seat buckles.
But I noticed when I was trying to put in these seat buckles, which is the ones that
came with the car, um, that they're actually blown.
I didn't actually know that.
I don't know why they are blown.
I did know I had an airbag light, but I did not know that the rear seats were blown.
So that is kind of crazy.
But thankfully, I think the M3 ones, which look a lot nicer, is going to work just fine.
I did literally notice, guys, that every single module, every single connector, everything
for the M3 is completely different.
So when you guys buy an M3, you're literally getting your money's worth because every single
thing is literally different.
I thought the modules underneath the frame itself is the same, but it's actually different
and I actually threw out one of them.
So I had to go get one from a dismantler and I had to go ahead and install it.
So I literally had to transfer every little thing.
So if you guys want to do a build like this, I do not recommend just buying an engine transmission
and buying everything else on eBay.
You're going to end up spending way too much money.
I definitely recommend doing what I did, which is get a donor car.
But yeah, without further ado, let's just go ahead and install these buckles and then
I'm going to give you guys a quick cinematic.
And guys, about a few days later, we're just sitting here.
We're honestly just chilling because I'm genuinely thinking about putting on this front suspension
and putting in the engine and transmission pretty soon here.
Like I'm thinking either this video or next video.
But just because of how long this video is, I think I'm going to go ahead and conclude
this video as of right now.
We didn't finish the wiring in the rear trunk area, but we did finish all the wiring for
pretty much the fuel tank, the rear buckles, this little rear section here, everything
in the front.
Literally it's all situated.
I'm going to leave it kind of bare looking for a little bit because I do want to retrofit
keyless entry.
I think it's going to be really dope.
I think it's going to be really cool.
So the next thing I'm going to go ahead and do is just install the engine and transmission,
put on that front suspension so we can kind of just get the weight of the car kind of
balanced out.
Because right now I'm literally using a cherry picker on the rear.
I have some tires right back here to make sure it doesn't fall back.
Literally all the weight on this car is on the rear and I just want it to be evened out.
We can actually sit this thing on the ground and be so much easier to work with once it's
on the ground.
So yeah, guys, I'm just going to have to conclude this video.
I hope in the next video we're going to try to get the engine transmission in and then
try to fully service that engine.
So if you guys are excited for that, make sure to smash the like button.
But without further ado, guys, I love you all so much.
Remember to stay humble.
I'll see you on the next one.
Peace out.
