How to Set Up Your 60 Gallon Air Compressor

Building in Progress
145 followers
Nov 2, 2022
A vertical 60-gallon air compressor is ideal for a wide variety of jobs,
from sanding and grinding to painting and drilling. But first you need to get it safely
installed in your work area. This video will show you how to safely transport and install
the compressor. Plan to use at least three people to unload the compressor in order to
prevent damage to the unit or personal injury. This unit weighs over 250 pounds and is top heavy.
Here are the tools and supplies you will need. 9 16th inch socket and ratchet, pipe wrench,
hammer, two adjustable wrenches, phillips screwdriver, flathead screwdriver,
hammer drill and masonry bit, quarter inch nut driver, socket or wrench, work gloves,
safety glasses, tape measure, vibration pads, thread sealant tape, strain relief, regulator,
coupler, reducer bushing, compressor shutoff kit, air hose, three eighths inch by five inch
wedge anchors, two inch pipe nipple, power cord or adequate wiring. Do not use a dryer cord.
This unit requires a dedicated 220 to 240 volt 20 amp circuit with breaker. If using a power
cord it also requires a 240 volt receptacle. Check your vehicle's manual to determine if
tailgate can support the weight of the unit. Move the compressor to the edge of the tailgate.
One person should remain in the truck bed. Lift the unit out of the truck. Two or more people
should lift the unit by the skid and one person should maintain unit balance from the bed of the
truck since the unit is top heavy. Move the unit to the installation location. Use a mechanical
aid such as a pallet jack or slide the unit on a skid to the specific location. Unbolt the unit
from the shipping skid. Use a ratchet with a nine sixteenths inch socket. Remove the unit from the
skid. This requires at least two people. One person to walk the unit off the skid and one to help
maintain balance so the unit does not topple. Place the unit where you plan to install it.
It should be located at least 18 inches from any wall or surface. Place pre-drilled vibration pads
under each foot to avoid unnecessary vibration which could damage the unit. Visit chpower.com
to order vibration pads. Using the mounting holes and the holes of the vibration pads as a guide,
drill holes into concrete using a three-eighths inch masonry bit. Holes must be drilled at least
five inches into the concrete. Place nut and washer on bolt. Thread nut onto bolt until tops are flush.
Insert mounting bolts. Use three-eighths inch by five inch wedge anchors to secure the unit. Strike
bolt with hammer until nut and washer are sitting on top of the compressor foot. Tighten nut using
ratchet with a nine sixteenth inch socket until anchor is set. Use installation torque specifications
of bolt being used. Loosen nut to leave a one sixteenth inch gap for stress relief during operation.
Next, check for the breather and filter. They may already be installed. If not, you need to install
the breather and the filter after you check your pump for oil. To check for oil, remove cap on pump.
Check oil level. Note, some models are shipped with oil in the pump. If oil is needed, refer to the
specification label on the compressor pump for proper oil capacity and oil type. We recommend
using Campbell-Hossfeld air compressor oil. You can also use mobile one synthetic 10w30 for normal
weather conditions or 5w30 for colder weather. Now install breather and filter if they are not
already installed. Next, you install a shutoff valve and regulator assembly. Sealant tape should be used
on all threaded connections to prevent leaks. Attach the compressor shutoff kit to the outlet port.
Attach two-inch pipe nipple. This length will ensure the shutoff lever has enough room to move
freely. Attach regulator so that the gauge is visible and unobstructed. For proper operation,
make sure the in and out markings match the airflow direction. Insert reducer into regulator.
Attach coupler to reducer. Move the shutoff lever to the closed or off position. For information
on proper installation of an air distribution system, please visit us at chpower.com or call
Disconnect, tag, and lock out power source before attempting to install this unit.
All wiring and electrical connections should be performed by a qualified electrician.
Installation must be in accordance with local codes and national electrical codes.
Recommended wiring. Hard wire from the circuit breaker panel or use a Campbell-Hossfeld
recommended cord designed for air compressor installation. If using the power cord, you will
need to plug into a 240-volt receptacle. Either system must be a three-wire setup with two hot
wires and a ground. Visit chpower.com or call 1-800-543-6400 to order a power cord. Remove the
pressure switch cover using a Phillips screwdriver. Remove ground screw. Install strain relief on
pressure switch. Attach strain relief nut to first few threads to allow for ground wire installation.
Do not tighten strain relief on power cord until wiring is complete. Insert the bare wires black,
white, bare, or green through the strain relief. Attach bare or green ground wires first to the
ground screw on pressure switch body. Loosen the terminal screws where line wires connect.
Match the black and white line wires from power source to the motor wires inside the
pressure switch. Match black to black and white to white. Tighten terminal screws. Tighten strain
relief nut. Place a flathead screwdriver into raised notch and tap screwdriver with a hammer
until tight. Tighten strain relief screws to hold power cord securely. Replace the pressure switch
cover. Knob must be in the auto position to sit correctly in place. Tighten the pressure switch
screw with Phillips screwdriver. Turn switch to off position. Restore power from main. Turn
pressure switch to auto on position. Compressor is ready for use. Follow break-in procedure from
owner's manual. If four wires are present from power source, cap off the neutral white wire with
a wire nut at the junction box. The neutral white wire is not used. Remove the pressure switch cover
using a Phillips screwdriver. Remove ground screw. Install strain relief on pressure switch.
Attach strain relief nut to first few threads to allow for ground wire installation.
Do not tighten strain relief on power cord until wiring is complete. Insert the bare wires, black,
red, bare, or green through the strain relief and attach ground wire first to ground screw on
pressure switch body. Loosen the terminal screws where line wires connect. Match the other line
wires of the power source to the motor wires inside the pressure switch. Match black to black
and red to white. Tighten terminal screws. Tighten strain relief nut. Place a flat head screwdriver
into raised notch and tap screwdriver with hammer until tight. Tighten strain relief screws to hold
flexible conduit. Replace the pressure switch cover. Knob must be in the auto position to sit
correctly in place. Tighten the pressure switch screw with Phillips screwdriver. Turn switch to
the off position. Restore power from main. Turn pressure switch to the auto on position.
Compressor is ready for use. Follow break-in procedure from owner's manual.
We hope this video is helpful as you prepare to transport and install your 60-gallon air compressor.
If you have any questions, please contact Campbell-Hausfeld customer service
at 1-800-543-6400 or visit us at chpower.com.
