Chair Rail Video (Part 2 of 2)

Building in Progress
145 followers
4 Video Views·Nov 2, 2022
Now let's get started. Now that the compressor is ready and your nailer is loaded,
it is time to gather the other items for your project and create a project plan sketch.
Let's review the tools and supplies you will need. Campbell Hossfeld trim kit, extra fasteners,
dual bevel compound miter saw, tape measure, level, pencil, wood putty,
paintable caulk, scratch paper, masking tape, stud finder, chair rail molding,
we suggest purchasing extra to make sure you have enough, 360 degree protractor angle finder,
only necessary if you suspect that you do not have 90 degree walls, finishing materials,
sanding block, paint and stain. Note, you may need a friend to help depending on the size of
your room. Now we're going to walk through some planning steps. A bit of preparation can really
help your project go smoothly. For example, it helps to draw out your room, labeling each corner.
Label corner 1 with C1 and corner 2 with C2 and so on around your room. Next label your inside
and outside corners. IL is short for inside left. IR is short for inside right. OL is short for
outside left. OR is short for outside right. You can also take note of the measurements of each wall.
Taking accurate wall measurements will ensure you purchase the right amount of molding for
your project. Remember, you will want to purchase more material than you need for practice cuts
and butt joints. You always measure twice and cut once. Along with preparation goes safety.
Always follow, read and understand the manuals and safety procedures of the tools you're going to use.
Always wear safety equipment. If setting up a cut feels awkward and unsafe, it probably is. Stop what
you're doing. Reset the cut. It is better to be safe than sorry. Next, let's talk about the cuts
you will be making for your chair rail. In our room, our corners are very close to having 90 degree
corners. We will fill any gaps with putty and caulk as a final step. If your walls are not close to 90
degrees, we suggest using a 360 degree protractor angle finder to determine your angles. Chair rail
basically involves making 45 degree cuts for two types of corners, inside corners and outside
corners. We recommend labeling your saw in order to make it easier to remember these corners and
angles. First, label the left and right side of your saw with L and R. Then, label the miter adjustment
on your saw. This controls the miter setting of your saw. We will refer to these labels as we go
through each cut. Now that we have labeled the saw, it is time to go over the miter setting chart.
Understanding this chart and knowing how to use it is necessary for setting your miter saw correctly
for each cut. Now, let's do some practice cuts. It helps to make practice cuts for all your corners
and label them. This step will also let you know how far your walls are off from 90 degrees.
For an inside left corner, refer to the first row in the chart. This shows that you need to set the
miter saw to the left 45 degrees. You also know from the chart that you need to place the wood
on the left side of the saw. Notice that the miter adjustment of the saw is towards the left label on
the saw and the wood is on the left side of the saw. Next, precisely align the saw blade so that the
blade is just right of your measured mark. Note, if you do not align your blade correctly to your
measured line, your board will be off the width of your blade, which is about an eighth of an inch.
This seems like a small step, but that small amount adds up quickly and creates unsightly gaps
in your joints. If this is the first time you have ever used a miter saw, or if you have not used a
miter saw in a while, you will want to practice your accuracy of aligning your measured mark with
the saw blade. Once your saw blade is correctly aligned to your mark, make your cut and label your
piece IL. Continue with an inside right corner. Referring to the chart and the label on your saw,
set your miter at 45 degrees right and place your wood on the right side of the saw.
This time, when aligning your saw blade, you will align it just left of your measured mark.
Make your cut and mark your piece with an IR. You have just made two left and right inside
practice corner pieces. These two halves will make your inside corner. Take a moment and see
how well you did and fit them together in a corner. If your walls are close to 90 degrees
and you cut the pieces correctly, they will tightly align in an inside corner. For an outside left
corner, set your miter at 45 degrees right and place your wood on the left side of the saw.
Notice when doing an outside corner that your miter is to the right, even though your corner
is to the left. When aligning your saw blade for an outside left corner, you want to line up your
blade just to the right of your line. Make your cut and mark your piece OL. Now, finish up with an
outside right corner, setting your miter at 45 degrees left and placing your wood on the right
side of the saw. Align your saw blade just to the left of your line. Make your cut and mark
your piece with an OR. Now you have the two outside corner pieces. Take a moment and see
how well you did. Fit them together in a corner. If made correctly, they align on an outside corner.
The other type of angle cut you may have to make is a butt joint. When a piece of molding is not
long enough to run the whole length of a wall, you will need to splice two pieces of molding
together. This is referred to as a butt joint. A butt joint consists of butting two 22.5 degree
angle cuts together to form a seamless run of molding. You want to plan ahead and splice your
butt joints together so they meet along a stud. Refer to the chart for specific right and left
joint cuts. Now that you have your practice cuts completed, it's time to measure and mark. First,
decide the height of your molding. Traditionally, chair rail is installed 32 inches from the floor.
We will be installing our chair rail 40 inches from the floor. Measure 40 inches from the ground
every two to three feet. Now that you have your line established, it is time to find your stud.
Using a stud finder, create a mark above your line where every stud is located.
Studs typically are 16 inches apart on center. Next, you want to measure your first wall and
mark your board in preparation for making cuts. Now you are ready to cut your first board. Follow
the method used with your practice cuts. Use the labels on your saw and refer to the chart to select
your miter setting and the proper placement of your wood in the saw. Take time to correctly align
your saw blade for the perfect cut. Now you are ready to fasten your board. Fit this first piece
of molding to its proper place on the wall, aligning it tightly in the corners, and with your 40 inch
mark on the wall, use your nailer to secure the first nail. Next, place the level on top of the
chair rail to make sure it is level. Keeping the board level, fasten the board to the wall at every
stud. Continue measuring, cutting, and fastening until you have come full circle in your room.
If you have walls that are especially long and cannot be completely fitted with a single length
of molding on a stud, join two pieces together with 22 and a half degree angle as shown.
This will prevent gapping from occurring. Use wood putty and caulk to fill gaps.
As a final step, you will want to sand anywhere you have used wood putty. Finish your molding to
fit your decor, either with touch-up painting or staining. There you have it! Beautiful chair rail,
like a designer room in your home. Thank you for purchasing a Campbell Hausfeld kit.
Visit our website, chpower.com, for additional information and for more project ideas.
