An Even BETTER Outdoor Sink!

DirtFarmerJay
310 followers
13 Video Views·Oct 23, 2018
It's been several seasons since our episode showing you how to construct an outdoor warm weather sink. After using it for several seasons, we've added a upgrade, as well as an alternative less expensive plumbing approach - but there's a catch!
Hey, Dirt Farmer Jay here from DirtFarmerJay.com.
Several seasons ago, we showed you how to do your own outdoor sink.
Well, since then, we've learned a couple lessons.
One, how to get it to drain better.
And number two, an alternative way to plummet that's a little bit more economical.
But there's a trade-off.
Stay tuned.
Having an outdoor sink like this is a great addition to your yardscape.
It's handy for washing vegetables, a splash of cold water in the face after a session of
weed pulling, or even a drink of water.
So there's a couple things that we've learned over the seasons that we've had this that I
think will be helpful to you.
The drainage system that we have on this is a short piece of discharge tubing that's normally
used for high-pressure pumps.
This depends entirely on pressure being put into it, and it's a little bit problematic
in use in this setting because the drain is gravity-fed only.
Generally speaking at work, if I turn this on and I adjust this around, I can get water
to come out of it okay.
But the slightest kink, and it'll tend to develop kinks over a period of time, results
in this.
Then you end up having to mess around with it and try to get it to drain correctly.
So a better approach to get it to drain dependably every time is to use a rigid hose like this
one.
Now you may recognize this.
This is vacuum hose that comes in a kit.
And we simply bought this kit like that.
And at the time of this filming, it's around $17 or $18 for a length of this hose.
Now the nice thing about this hose is it's not going to collapse.
When you buy it, it's going to have ends that are on it like this on both ends.
And what we did is we just took a utility knife and cut it off and got rid of those
and ended up with this piece of hose.
Now what we're going to do is we're going to replace this limp discharge hose here with
this rigid hose here.
So here we go.
So as you can see, that slides right over the tailpiece, no problems at all.
And you probably don't need a clamp on it.
If you do want another clamp, you can go and buy one and cinch that down.
But it stays in place.
So let's see how it works.
We're going to turn that water on and see if we get any backup.
Well, no.
Take a look there what's happening.
All right.
Now that we've told you about an enhancement on the drain side, there's an alternative
way to plumb this that is a little bit more economical.
But there's a trade-off I'll tell you about in a moment.
If you recall from our earlier video, the way this is plumbed is this is attached to
both stems of the valve up here.
These are standard 1 1⁄2 inch pipe thread.
And it takes an adapter, which you can see right there, to change it to hose thread.
This is a standard Y adapter that's used commonly in laundry settings.
Now, we can do a direct to one side of this and cap the other side.
The disadvantage is that only one valve will work.
But if that's all you need and you want to save a little bit of money, that's just fine.
Now, there's one other thing I'll show you right now.
Notice when I have water going on both sides here that when I turn on one valve up here,
I have a nice stream of water.
I also get more when I turn on the other valve.
So if volume is important to you, you want to invest a little bit more
and do the Y connector as in the original video.
If that's enough water for you, then I'll show you the other way to do it.
Watch this.
So what you see right here is the adapter.
This is female thread, standard plumbing thread for pipe.
The other side is male hose bib adapter, which allows the hose to be screwed directly onto it.
We've also learned to use this kind of laundry hose.
This has a stainless steel braided jacket on it that protects it from UV rays,
keeps the hose stronger and supple much longer.
There's a washer inside at the base of this, so I don't need to put pipe dope on it.
All right, now that we've got that set up, let's see how it works.
Well, if I turn on this valve, nothing happens.
It's inactivated.
However, when I turn this one on, you've got a pretty good volume of water.
You've saved the price of the Y adapter and the stem adapter that goes on the faucet.
It's up to you to determine if this is a sufficient volume of water for the sink.
And you'll have to remember which valve works and which doesn't.
But you get some great economics.
Hey, if you missed the first video and you want to watch it, visit the link right here
and you can take a look at how we constructed this.
If you found this video to be helpful to you, why don't you like it?
Better yet, subscribe to our channel.
Until the next time, this is Dirt Farmer Jay from DirtFarmerJay.com.
