4WD Diff Breather Kit Install - Protect Your Drive Line #ShedSessions

Traveling on Wheels
7 followers
6 Video Views·Oct 23, 2022
So, you want to put your car through some puddles.
You want to do some river crossings.
You want to submerge your vehicle.
I get it. It's exciting stuff.
Everybody wants to do a river crossing at some point and test out their rig.
Normally, it's a bad decision that is fueled by a mate that's in the passenger seat,
who normally doesn't own a four-wheel drive,
sits there and says,
It'll be fine. What's the worst that could happen?
You've got a tough rig, mate.
You've done all the mods to this thing.
Just go through the water.
What are you, a bloody chicken?
You sit there and you go,
I've lifted my car.
I've put bigger tyres on it.
It's a four-wheel drive and it's in four-wheel drive.
I'm just going to send it.
What's the worst that can happen?
Welcome back to JPC.
Another Shed Sessions video for you guys at home watching this video.
I do it for you.
Now, if you guys want some merchandise,
JPC merchandise, Shed Sessions merchandise,
click on the link below in the description.
Hold on a second.
I need merch in order to sell merch.
I need to have merch on the description link below.
If you guys think that I should have some JPC and Shed Sessions merchandise,
let me know in the comments below.
I'll make it happen.
I honestly just didn't want to be another one of those people that have the merch,
but I've had a few people message me asking me about it.
Anyway, another installation video for you guys today.
This is a cracker.
An absolute must for anyone,
anyone who has a four-wheel drive and takes it off-road, overlanding.
You need to have this on your rig.
Very easy installation, guys.
Something definitely needs to be done.
If you've already got one on your car, you're an absolute legend,
but keep watching the video now because it's really cool.
What you can do to your vehicle to prevent there from being some serious implications
to the drivetrain from doing water crossings is a few things.
It's a simple checklist, but it's something that you should definitely do
to make sure that you don't have issues with your rig.
Number one is a snorkel.
You need to put an engine straw on your rig, guys.
This is going to prevent water ingress into the intake and into the engine,
which is catastrophic.
We all know that.
That is the main one, and we've already done it on the build series, guys.
You can check out that video.
I'll put a link to it at the end of this video.
The other thing which commonly gets overlooked is breather kits.
Your transmission, your transfer case, and your front and rear diffs
need to have breathers on them
because when you are driving around through the hills,
four-wheel drive tracks, normal driving,
all of your drivetrain is warm.
Teal it up, guys.
It's being used.
You know, the oil's hot.
The metal's hot.
Everything's warm.
So what happens is you go up to a water crossing, you hit that water,
and just like when you jump in the water, your body temperature changes,
your drivetrain temperature changes.
And this causes a vacuum.
So what happens then is water or air,
and most likely water if you're doing a water crossing,
gets sucked in to your drivetrain bits and pieces.
And this is going to mix with oil.
Now, you might be thinking,
I haven't done a diff service or a transmission service in a while.
My oil levels are a bit low.
Chuck a bit of water in there.
Top her up.
She'll be sweet.
But no, that's not the case.
Water and oil does not mix.
And installing a diff breather kit and a transmission breather kit
is a very cheap investment in the more expensive components of your vehicle.
Now, this is a Blackhawk product.
It's manufactured by RoadSafe,
and it's distributed by the 4Wheel Driveshed.
So, I'll chuck a link in the description below, guys,
for where you can purchase this one,
a link to the 4Wheel Driveshed,
if you're interested in getting this kit for your ride.
Now, let's get started with the unboxing of the product.
First and foremost, to check out what you get for the money that you spend on this kit.
And then, let's get stuck into installation on the car, guys.
Super exciting stuff.
Let's do it.
So, first thing on the top of the box there,
we've got some pneumatic air line.
Different sizes, I'm guessing, there.
And another big bundle of pneumatic air line right there, guys.
That's fantastic there.
They're giving you heaps of pneumatic line there to work with.
So, perfect.
Got some cable ties, bag of cable ties,
and there is plenty in there.
That's going to be more than enough to get the job done.
So, now that I've used a fistful,
enough to sink the Titanic of zip ties,
pretty much everything that came in that bag, I used.
And then, we've got another bag here filled with some other goodies.
Inside this bubble wrap is the actual manifold itself.
So, that is a machined, billet machined,
aluminium manifold.
So, high quality.
And you can see there that it's been machined in the back housing,
where the actual breathers,
the breathers go into here and they're recessed.
So, they keep out of the way of all the dirt and stuff
that's probably going to be traveling around inside the engine bay
and give it more chance of those filters keeping clean.
And we've got a wide variety of pneumatic fittings here.
We've got some metal push lock fittings here.
Okay, then we've got some straight push lock pneumatic fittings there.
We've got some 90 degree fittings in that bag.
We've got a reducer block there.
And then, we've got a two into one pneumatic fitting.
Alrighty.
And that looks like that we've got our mounting screw
for the actual manifold itself.
We've got some blanking grub screws there.
And the actual breathers.
They're the brass breathers which screw into the manifold block.
Alrighty, now we've got all of the bling
laid out on the bench from the Blackhawk breather kit.
Looks really good.
This is some high quality gear, guys.
I'm stoked.
Now, this is something you can do at home.
You don't need a hoist.
This is a non-hoist certified installation.
The only reason I'm using a hoist is because
I can get better camera angles underneath the car
to show you guys how to do the install.
It's so much easier than having the camera on my chest
trying to do all the things underneath the car
and get all these shaky angles.
We are now in the engine bay, guys.
And I have found a spot for my manifold.
After scanning the whole engine bay
and trying to figure out where the highest point was going to be,
but also somewhere that this thing can mount
and I can get all the cables run to it neatly.
And I've found the perfect position.
And there you have it.
It's going to bolt straight onto there.
I'll have my 90 degree fittings coming off the back
and all of the hose can continue to run up
these hard brake lines behind here
up into the block itself, the manifold block.
The hose will all come from the back,
be nice and neat and all join into the middle.
So, that is going to be my position for the manifold, guys.
Again, you can choose to put it wherever you want to put it,
but this is probably the best spot in the engine bay to put it there.
So, before you put your manifold into your chosen position on the vehicle,
you'll need to make sure that you put your breathers on
and you can even go ahead and put the other fittings on as well.
Now, you've also got these grub screws here as part of the kit,
which are basically blanking caps.
So, if there's any fittings or locations that you're not going to use,
just put a blanking cap in there.
Otherwise, it will get water or dirt ingressing through there
and it completely defeats the purpose of it.
So, make sure you block all the holes with at least a fitting,
a breather or a grub screw.
And like all other threads, just make sure that you start them by hand first.
Get the thread started and you can grab yourself a 12mm socket
and you can go around and do them up.
Don't need to be overly tight.
Once you've got them sort of seated flush like I'm doing here,
you can grab your ratchet or whatever tool you're using to do them up.
That's about it there.
It starts getting tight about there and I just go a little bit further.
Okay, so we are at the back of the vehicle.
We're at the rear differential.
Now, that is the breather line, that one right there.
It runs up into the chassis.
So, it doesn't actually go into a breather block
or a breather fitting or anything like that.
Basically, that's it there.
Runs up along here, up through there and straight into there.
So, I'm tipping if we...
Oh, well, yeah, there we go.
If we pull on that, the hose comes out and there's nothing on there.
We literally just ran into that fitting in the chassis in there.
So, guys, therein lies the problem.
If the water is up to your chassis height,
you're going to run into troubles
because there is nothing on the other end of that.
Focus, focus.
There's nothing on the other end of that that is stopping water ingress
when the diff wants to suck air in.
So, once you've taken your rubber hose off the breather barb in the diff housing,
grab yourself a 12 mil
and you need to undo this breather barb out of the diff housing
and we're going to replace that with a push lock fitting.
One of the pneumatic ones that are supplied in the kit.
We've got some big life decisions to make, guys.
So, these are two types of fittings.
They've got the straight fitting there or the 90 degree fitting.
Now, both of them are the correct thread size.
So, you could use either one in your Nissan diff housing
but they're going to be different.
So, one of them is obviously going to kick the pneumatic airline straight up
and the other one's going to kick it out on a 90 degree angle.
Now, this is completely dependent on how you're going to run
your pneumatic airline to the front of the vehicle.
I have an idea on how I'm going to do mine
and I'll show you in a second.
I'm going to be using a straight fitting.
Okay, so we've got our pneumatic push lock fitting here.
Now, no need to use any thread tape on the fitting itself.
It's already got a thread compound on there ready to go.
You will just need to grab yourself a 14 millimeter spanner,
socket, whatever you want to use to put it into the diff.
So, go ahead and do that now.
Now, when you're doing up these fittings,
there is no need to go overly tight with them, guys.
Just when they start getting firm, just go a little nip up more than that.
Don't go too much more.
You don't want to strip the thread or break the fitting off in the housing even worse.
So, because it's got that thread compound on there,
you don't have to go up overly tight.
It's going to get a good seal no matter what.
So, now you've got your push lock pneumatic fitting installed into your diff housing.
What you need to do is grab your pneumatic airline,
the big roll of it.
This is perfect for the rear diff because you've got a lot of length in the line.
And we're just going to leave it the length that it comes in the kit.
Don't trim it down unless you're 100% certain of the length hose that you need.
I'm going to leave it as long as it comes and basically just feed this
from the pneumatic fitting, from the diff housing,
all the way up to the diff breather kit in the engine bay.
So, I'll trim it up once it's up in the engine bay.
I'll know exactly then how much I need it.
All you need to do is grab one end of it
and press it into the push lock fitting you've installed on your diff.
It's just a press fit, guys.
And it will clip into place as soon as you press down on it
and it locks it in with jaws inside the fitting.
Alrighty, that's done.
So, that's pressed into the fitting now and it's not coming back out.
I've made sure it's got a good clamp by pulling back on it
and it's definitely not going anywhere.
I've got the other end of the hose here ready to take up the front of the vehicle.
But first, what we need to do is make sure that we can get this hose
from the diff to the chassis safely without having it too short.
So, when the diff flexes up and down, it's not going to stretch the cable and break it.
So, call me crazy,
but these brake lines are an extended braided brake line set that I've installed on the vehicle.
Now, I know that those lines is long enough for when the diff flexes all the way down,
it's got enough length in it that it's not going to break.
So, if I jump this cable from the breather fitting over onto the brake line
and just cable tie it up along this brake line to the chassis,
I know that if it's the same length as that,
it's going to have enough length in it to flex with the diff.
So, that's exactly what I'm going to do.
There we have it, guys.
The rear diff breather line routed up along the brake line there,
up to the chassis and up along the hard brake lines.
Then it goes up there over the top of the fuel tank.
Now, I've come on the outside here.
Up in there, there's actually a factory bracket right there which houses the brake line.
So, I've just undone the 10mm bolt on the outside,
put a little bit of conduit around the breather line there, as you can see,
and just pinched it into a spot which was actually spare on that bracket.
So, that worked out really well.
Then I've come down here, tucked down onto the inside of the chassis rail
and then continued to run along those brake lines there, the hard lines,
cable tying it along the way, dropping down there, up here and over the chassis rail.
And then I've just put the rest of the line up in the engine bay up there for now.
Now, a few tips.
No matter which way that you route the cable up to the front of the vehicle,
you need to make sure that it isn't going to rub through.
So, make sure it's not somewhere where it's going to have a moving part
that might rub against it and cause it to break through this.
Even though it's got a really thick quality wall on it,
eventually, you still could have some dramas.
And the main thing, the main thing, keep away from heat.
Okay, so that's the rear differential breather fitting location.
Nice and easy to show you guys, heaps of space.
The other three breathers though are a little bit harder to get camera angles of.
So, I'm going to overlay some images now and explain them in more detail.
So, this is a manual transfer case bolted to a manual transmission
and you can see the breather location there,
the hose going onto the fitting up the back of the transfer case.
So, that's much the same on the auto transfer case as you can see here,
the line going onto the breather fitting just behind the mating surface.
So, the breather lines on the manual transmission themselves are located right there,
the top hose going into a fitting,
the bottom hose is the one coming from the transfer case.
They both run up to a fitting block on the bell housing,
which is bolted on normally but hanging down there at the moment
because there's no bolt in it.
So, the automatic transmission is very easy to see,
clearly visible the fitting location up the top there with the breather line going into it
and the bottom hose is the one coming from the transfer case.
And those breather lines run up to a block on the front of the bell housing
much like the manual would have,
those pipes right there are the breathers for them.
Okay, now this one here is the front differential
and exploded diagram of your front diff in your MP300
and you can see right there that is the breather fitting guys.
So, straight into the side of the housing on the passenger side of the vehicle,
nice and easy to get to.
So, that's pretty much the breather locations,
the fitting locations of the other three spots on the vehicle.
So, the transfer case, transmission and front diff.
Now, what I'll do guys, I'll just cut back to the vehicle
and I'll show you exactly how I'm going to put the breather line up to those fittings.
We need to get some breather lines onto the transmission and transfer case.
Now, those images that I just overlaid for you
and explained the fitting locations on both the automatic
and manual transmission and transfer case,
that at least shows you now where the fittings are.
So, this is one of the rubber lines off my transmission.
I've pulled it off to show you guys what you can do
as an option.
So, you can actually grab your pneumatic hose.
It's supplied in the Blackhawk kit and your factory rubber line
and you can just push the pneumatic hose inside the rubber line.
It's actually a really snug fit
and you can even put a clamp around this after you're done if you like
to make sure that it's nice and tight around the pneumatic hose.
But, that's it pushed in there.
It's a really good fit and I actually can't get that off.
I did a test before and I could pull it apart but it took a lot of force.
So, as you can see, that is a pretty snug fit, guys.
Not a bad option.
But, me being OCD, I need to have everything nice and neat in one piece.
So, what I'm actually going to do,
and I've done this before and I know it works,
is you've got your pneumatic hose.
I'm going to take a heat gun to the end of the pneumatic hose
and I'm going to heat it up so that it's a little bit malleable
and it will form.
So, then what I'll do is I'll push it over the fitting,
the factory fittings on the transmission and transfer case
and as this pneumatic hose cools down when it's pressed onto the fitting,
it will actually form to the fitting and create a shrink fit.
I've done a test for you guys here to try and show you what I'm talking about.
So, this is that breather block off the front of the bell housing
which I've removed because I was going to try and use it,
but you can't because it's brazed together on the end here.
So, I've just heated up the pneumatic hose,
pressed it over the other end of the fitting
and as you can see, that is not going anywhere.
It is just so tight on there, guys.
So, that is what I'm going to do.
That way, I can get rid of the factory rubber hoses
which, in my opinion, are a little bit too loose on the fittings now
and I don't trust them.
I'd probably put clamps on them if I was to leave them on there.
So, I'm just going to delete them and get rid of them all together
and then I'll just run this up from the transfer case
and the transmission up into the engine bay through the front.
So, up to the bell housing and then up into the engine bay from there.
It takes a lot less pneumatic hose to do that.
The transfer case fitting is there.
That's just coming off the transfer case up into that P-clip
and then there's another P-clip a little bit forward from that one just there
which houses both the transmission and the transfer case line.
So, they start to sort of jump in together there.
You can see the transfer case one coming from the back
and the transmission just looping over from the other side there into that P-clip
and then just runs over to the front of the bell housing
and then there's some electrical cable there with some conduit around it.
So, I've just basically cable tied the pneumatic, two pneumatic lines to that
and then from there I leave the cable.
I leave the conduited cable just there and I jump across over
onto the same spot that the other lines are running to
and then just up into the top of the engine bay.
If you're keeping things simple
and you're connecting the pneumatic line up to the rubber line
you can connect it up to this rubber line in the engine bay from the front diff
like you did on the transfer case and the transmission.
That's it right there guys, right next to the battery tray.
Probably the only diff breather that Nissan actually got right
because it's right up in the engine bay.
Although it's not the highest point it is still up in the engine bay
and it basically runs down there.
So, that's it there which runs down to the front diff all the way down there.
If you're heating things up though
you can grab your pneumatic airline that you have left over
from all the other ones we've already run.
Grab your heat gun and heat that bad boy up.
Press it onto the barb, run it up into the engine bay
and then all we need to do is connect those pneumatic lines up to the manifold
and it is done.
Now the good thing about the front diff in our vehicles guys
in the MP300s and other IFS vehicles
independent front suspension
is the diff center is solid mounted to the chassis
which means that it doesn't move.
So, we don't have to have a heap of slack in this line
we can probably use the standard guides that this rubber hose runs through
up into the engine bay.
We can use those and then run it up to the manifold block.
You can essentially do that however you want
but that's probably what I'll end up doing and I'll show you once I'm done.
So, I was a little bit unsure as to what this coiled pneumatic line was for
but after reading the instruction manual guys
this is actually a diff dropper coiled line.
It doesn't really work for my application
but maybe for you guys that have like Nissan Patrols, Toyota Land Cruisers
this might work actually quite well.
So, it's basically a sprung pneumatic line
so when the diff drops down it opens up and coils back together
after the diff returns to its factory height.
So, good to use but not for my application.
I just thought I'd let you guys know what it is and why it's in the kit.
Nice and squishy.
So, there we have it on the front differential housing
on the passenger side just up the top there guys
that is the pneumatic airline pressed onto the fitting on the factory housing
and that just runs straight up into the engine bay
kind of following the path of the original rubber line.
So, if you follow that up into the engine bay
and then up to the breather block itself
you won't have any dramas guys.
Nice and simple.
Again, just applying a little bit of heat to that pneumatic line
and then pressing it on
and it's a form fitment now after it's cooled down
went on nice and easily.
So, we're up in the engine bay guys
and this is the manifold block right here that we fitted up before.
We've got the four ports on top, the pneumatic fittings
and I've got two hoses over this side
the two pneumatic hoses that are already plumbed in.
That is for the front and rear diff
so I've chopped them down, trimmed them down to size
and pushed them into the pneumatic fittings right there.
So, they're done.
Now, I've got the two lines here.
This is for the transfer case and the transmissions.
So, I just have to trim these guys down
chop them about there
and then push them into the pneumatic fittings
and maybe just a couple more zip ties in the engine bay here
holding all these hoses together and things like that
and that will then complete the installation of the breather kit.
The breather kit is now on the vehicle.
Pretty easy install guys.
I don't think there was anything really there that was too difficult.
Maybe getting some of those pneumatic lines
squeezed onto the factory fittings on the transfer case and transmission
may have been a little bit of a stretch with the old arm
trying to get up in there and push it on
but once they were on it was really satisfying
to know that I wasn't using any of that factory rubber line
which was loose on those fittings
and probably not working anyway.
So, I can now safely put my MP300 through some puddles
without risking intake of water into my drivetrain.
So, the install itself was pretty darn straightforward guys.
Definitely something that you need to do to your four-wheel drive
if you're going to go four-wheel driving
and put it through some water.
Even if you don't think you're going to, you may.
So, it's best just to get one on the car.
They're really inexpensive guys.
If you want to grab one for your car
you can jump on the four-wheel drive shed's website
or give them a call in the office.
The guys over there will help you out with anything
four-wheel drive related.
They are on top of it guys.
They will get you sorted with everything that you need.
Just a side note on this as well
it doesn't negate the fact for general servicing
on your diffs and transmission and things like that
mainly your diff housings.
Now, that wraps up this video guys
but if you want to see more of this content
don't forget to hit that subscribe button
it helps me make more of this content for you guys
and if you haven't already
if you enjoyed this video drop it a thumbs up guys.
If you have any questions for me about this video
you can drop it in the comment section below
and if there's any videos that you want to see me do
that I haven't done yet
and it's something that you really want to see me do
on this channel
drop it also in the comment section below guys
and I'll see what I can do.
Maybe I can make it happen, maybe I can't
but if I can, I will.
Anyway guys, this has been another
JPC Shed Sessions installation video.
I'll catch you guys in the next one.
Bye.
