I Found This Broken Bolt in the Crankcase of my Cheap Range Rover’s Engine! [Part 3].

Drive Time
10 followers
5 Video Views·Oct 22, 2022
This is my 2011 Range Rover that I purchased at a Copart auction with mechanical damage.
You see where it says enhanced vehicles? That's code for the vehicle doesn't run.
You see these 5 liter Jaguar V8s are notorious for having timing issues which can lead to
catastrophic engine failure. My name is Waldo and previously in this series I got the engine
running but I detected the telltale sound of an engine that's suffering from serious timing issues.
I'm determined to fix this issue though it's not going to be easy.
The factory service manual says this is a 12.2 hour job requiring quite a few special tools.
I've ordered all the parts including revised parts to fix the timing issue permanently.
Now luckily when it comes to mechanics I'm YouTube certified so hopefully there shouldn't be
any issues there. As for special tools one of my viewers Joe was nice enough to lend me his set of
Let's start by getting the budget Range Rover into the budget shop.
Well this work isn't going to do itself so let's get to it.
The first thing I really need to do is just remove a bunch of stuff to gain access.
I'm at the first point where I need to stop and use a special tool this slide hammer here
in order to get the fuel injectors out. Now I've heard that these can be pretty difficult to remove
so that's why I opted to do this first while the engine is still warm. My thought process
is that while the cylinder head is hot the holes are larger and then these should come out easily
and look at the results. One of the fuel injectors actually came out with the fuel rail and it also
happens to be the one all the way in the back there that's the hardest to get to so that's a win.
So how this works is I stick this collet over the fuel injector,
lock it, and then I can pull it out with the slide hammer. Look at that great success.
All right I got all eight injectors out and I did end up having to remove the cabin air intake
that goes right around here in order to get access to the back injectors. All right so next
I need to drain the radiator in order to remove it and a bunch of other stuff on the front here
to make room and this is pretty much guaranteed to make a huge mess. Oh no take a look at this.
See all those copper flakes at the bottom of this? That's really bad news. So I did a little bit of
research to confirm my suspicions and I found that there are a number of radiator coolant
stop leak products that contain copper colored flakes like what we found in the coolant over
there. Those stop leak products are also advertised as solving head gasket issues
and that really makes me wonder if that's what we're dealing with here. Now this brings me back
to part one of the video series where we found the half empty bottles of coolant in the boot and
well I also found the business card of the previous owner and called him up and when I asked
him about those he told me that those were from when he had the water pump replaced I believe
and he never mentioned anything about the vehicle overheating or having a head gasket issue.
I assumed that he was just using them to top it off because maybe the water pump was leaking but
I wonder now if maybe the water pump was leaking so much that the coolant ran out in the vehicle
or got very low and overheated causing a head gasket issue. Now there is one other piece of
evidence support a possible head gasket issue and that is there is a lot of water vapor coming from
the exhaust when the engine is running. Now I was kind of hoping that this is normal or maybe it
would go away or something like that but it's kind of the elephant in the room at this point
and I don't think I can ignore it any longer. On the other hand we tested the compression and the
compression results were pretty decent so if there is a head gasket leak at least it's not very bad.
The problem is with the plans that I'm considering for this vehicle even a small coolant leak is
unacceptable. I'm kind of thinking at this point my best bet is to pull the cylinder heads off so
that I can take a look at the head gasket. I can also measure the heads and the block mating surface
for flatness to see if it's warped at all from overheating. It certainly would be interesting to
see a bunch of that copper colored gunk sealing up part of the head gasket which would tell me
immediately that's what the problem is. As for the amount of extra work that it would be to pull the
cylinder heads off at this point I don't think it would be that bad because I need to do most of the
work that it would take anyway to access the timing components. This project has been a little
bit of a roller coaster ride so far with this part definitely being a negative downturn but I am not
giving up. Other YouTubers have tried to get cheap Range Rovers before and failed and I certainly
don't want to add myself to that list. While I have this thing up on the lift I removed the starter
and that brings us to special tool number two. This thing's job is to hold the flywheel in place
while I remove the crankshaft pulley when I get to that part. With the tool bolted in place the
repair manual says to inspect it to make sure the tool is correctly locked in between the flywheel
teeth. Who'd have thunk a lighted inspection mirror would come in so handy. I'll go ahead and put a
link in the description. Now I can lower the vehicle and start removing parts at the front
of the engine. All right special tool number three. This thing bolts onto the crankshaft pulley
and holds it in place while you use this special socket which fits in the middle to loosen up the
crankshaft pulley bolt which is very tight. So I'm loosening these bolts on the crankshaft pulley and
look what I just noticed. There's a hole in the timing cover. I don't think that is supposed to
be there. Now I'm really interested to take a look inside to see what's going on. I guess that
explains all of the oil that is soaking the front of this engine. It kind of looked like it was
coming from the oil filter housing so I assumed that maybe someone did an oil change and didn't
put it back on right but it might be coming from that hole. Anyway I have the tool installed here
and I have this end of it held up by a two by six that's going to keep this thing from turning.
I'm going to use a big three quarter inch drive ratchet for this part
and a pipe. Notice I'm turning this clockwise. That's because this is a left hand thread bolt.
Special tool number four. This screws in where the crankshaft pulley bolt was and then this part
screws to the pulley itself and then as I tighten this up it pulls the pulley right off.
All right so let's take a look in here and look at this. The very first thing I see
that I mean that looks like it's probably a piece of the tensioner guide. That's no bueno.
Take a look at this. It looks like the timing chain guide bolt broke off and then moved around
in the tensioner wallowing out this hole and also wearing a hole in the timing cover. At some point
the bolt probably hit the crankshaft pulley causing it to break the timing chain guide.
This would have caused oil to leak out of the engine eventually causing the knocking noise
that we initially heard. As for the timing chain noise the broken guide definitely could be a
factor but I also noticed that the tensioners are the old design so this engine may never have had
the timing fixed. Once we get the tensioner guides off we'll be able to tell for sure by inspecting
them. In order to do that I first have to remove the valve covers followed by the upper timing
covers. The first thing we do is take out these tensioners. You can see what they look like.
Definitely the old style tensioner. It still does have some spring pressure there which is good.
It is of course hydraulically controlled to give it its full pressure but it seems like it's still
in decent shape. Well this one seemed fine until I pressed in too many times and now it's stuck
so I'm not sure if this one is okay. I don't know. Either way of course I'm replacing these.
And now for the part I'm really excited about. Tensioner. Oh yeah that is definitely the old
design of tensioner and it is very worn out. I think it's very likely that this is the issue
or at least one of the issues. If we compare the old and new guides you can see that the old design
has a soft aluminum surface where it's contacted by the tensioner. Over time it wears out causing
reduced chain tension. The revised design has a hardened contact point to eliminate this issue.
All right so take a look at this guide here. One bolt, two bolts, three bolts. Now let's take a
look at the broken guide. So there's a bolt right there. There's supposed to be a bolt right there
in the middle and then the last one is supposed to be right there as well. And look look at how
much this thing moves around. How loose it is. That is absolutely crazy. No wonder this thing
was having issues. The one on the other side it's a little bit loose but not too bad. Yeah so this
middle bolt here must have come loose and fallen down there. That could have been absolutely
catastrophic if that fell into some moving parts so I guess this is really lucky that it didn't.
I wonder if it's at the bottom of the oil pan right now. Ah okay we can actually see that that
bolt broke off as well. Well that is really weird but once again inspection mirror for the win.
Oh there it is down there. Can you see that? So this thing obviously has some serious timing
issues and I could reassemble it right now with the new timing components that I bought and it
should fix the timing permanently. However don't forget that I suspect this thing also has some
head gasket issues. So the next steps would be to remove the cylinder heads so that I can replace
the head gaskets and of course inspect the cylinder heads themselves to make sure they
haven't warped from overheating. Now removing the cylinder heads is certainly doable with the
engine in the vehicle itself however it is easier to do with the engine out of the vehicle and that
brings me to the next point which is I'm sort of considering doing a full engine rebuild. With all
of the time and effort that I'm putting into this and considering how stripped down the engine is
going to be, how much work would it really be at this point to do a rebuild? Don't forget that we
discovered in part one that there is cylinder scoring on the left bank of cylinders and
eventually that is going to turn into piston slap at which point the engine is going to need to be
rebuilt or replaced. Now I don't know how long it'll take before it gets to that point but it's
probably somewhere in the tens of thousands of miles. I know I had said in part one that I did
not want to do a rebuild on this but here I am at the end of part three and I'm thinking about doing
an engine rebuild. What I would do is have the cylinders bored out and honed, throw some
oversized pistons and rings in there, throw some new bearings in there while I'm at it and the
result would be an engine that is basically brand new and should last 150-200,000 miles.
Wouldn't it be pretty cool to have perhaps the first Range Rover ever to hit 300,000 maybe 350,000
miles? In any case let me know what you guys think about this. Should I rebuild the engine? Should I
just pull the heads off and replace the head gaskets? Also let me know down in the comments if
you know where I can get any oversized pistons because I've done a little bit of searching and
I haven't found anything yet. If I do decide to rebuild the engine at least I will end up with a
really nice car considering how good the physical condition of the body and the interior is. Thank
you guys so much for watching and we will see you in part four. Aspen up, good girl. Aspen off,
good girl.
