Honda Accord Hybrid Mechanical Review | The Failed Hybrid

The Auto Geek
46 followers
70 Video Views·Oct 18, 2022
Today we're going to be reviewing the Honda Accord Hybrid. Not like other reviewers that
would blast hybrids for their sluggish driving performance, yet praise them for their fuel
economy, we're going to be taking a look under the hood and underneath this Accord to see what's
inside and how it works and what Honda has done to transform their regular Accord with very
primitive technology into a hybrid. Now we're going to start under the hood where we have Honda's
J30 V6 engine. Now this is very similar to the engine used in the regular Honda Accord,
although the engine heads are different because it uses their i-VTEC system for cylinder deactivation.
Now sandwiching between the engine and the transmission on the driver's side is a thin
electric motor and you can see that high voltage orange cable that will run to power it and then
underneath the driver's side airbox we have a slimmed down version of the automatic transmission
and that's because this entire thing is packaged in the same packaging as the regular Accord.
And that's probably the reason why the Accord Hybrid didn't succeed as well,
is because they chose their V6 engine paired with an electric motor to boost power, so this is more
of a power hybrid. It doesn't run on the electric motor exclusively as opposed to using a fuel
sipping four-cylinder with a CVT like the Camry or Altima hybrids of the mid-2000s. Now taking a
look at some of the components under the hood here, the engine is situated transversely for
front wheel drive. We've got a washer reservoir here and the ABS motor. Over in the corner there
we have the master cylinder, fuse box, air box and the battery as well as the coolant reservoir at
the front. Now we're going to start by taking a look at the air intake system of the Accord.
Hot air from the engine bay is drawn down into this tube here. It'll go down into a reservoir
underneath the battery and then back up through this air box to get filtered out, then pass the
mass airflow sensor and then into a drive-by wire throttle body and into a rather large air intake
plenum bowl here where it'll then get distributed to each head at the front and the back. Now
surprisingly for an older car, accessing the air filter on these is a little cumbersome. You do have
to use tools to loosen off these eight millimeter bolts and then disconnect the mass airflow sensor
and then once that's done we have to lift off the air box and because of this accordion here things
are going to get pretty difficult to remove. Yeah this thing is super cumbersome. Then you've also
got a hard line that ties into here. Now these accordions are known to break. You can see this
one actually looks like it's been replaced before. Pull it off from the throttle body, maybe that
will give me enough room to finally take out that air box and then I can access the air filter. Now
once the air box is removed you have clear access to this drive-by wire throttle body. Now once the
air makes it into this air intake plenum it does have this motor here that's going to control a
flap on the inside here and that's either going to adjust for higher airflow or better mixing at
lower rpms. Now taking a look across the top of the engine here we do have metal valve covers
on the front and the rear. We've got this oil dipstick here and this does take 5w20 weight oil.
Now taking a look underneath the accord hybrid things are generally pretty flat. There's no real
attempt at smoothing things out for aerodynamics. As a result everything is exposed and because
it's exposed it's going to start to rust as you can see here. A lot of older Hondas had problems
with rusting. This one is no exception. It's definitely a victim of too many Canadian winters.
Over on the passenger side here we've got this oil pan and the oil drain plug. Surprisingly this
oil pan is actually made of aluminum. Now like on most V6 Hondas the oil filter is located inside
this little cavity here for the control arm on the passenger side just beside the wheel here.
It's kind of open and exposed to a lot of debris hitting it which I don't like but it is a spin
on style filter which is going to make for pretty quick and easy oil changes. Now changing spark
plugs on this is pretty straightforward. You have three ignition coils over here to access the three
front ones. Now accessing the three spark plugs at the back are pretty straightforward. Unlike
Nissan or Toyota where you have a big intake that scoops over the rear that you have to remove.
This one the intake is nice and flat and so that means you can easily access the rear spark plugs
once you remove this high voltage wire. Now on the passenger side of the engine underneath this
cover here we do have a timing belt which means that you will have to service it every 90 or 100,000
miles to replace it. Honda still uses timing belts and their V6 is up to today. Anyways the water
pump is also buried down powered off of the timing belt inside of there so when you do service this
timing belt you should probably change that water pump out as preventative maintenance. Now working
inside of here is pretty tight you've got a lot of components right up against you here to work
against especially down at the back here where the rear camshaft is. You will have to remove this
engine mount and some of the clutter around here just to try and work but it's a pretty tight job.
Now if you're familiar with other V6 Hondas you'll notice that there's a couple of accessories that
are missing from the front half of this engine. Usually in this cavity over here you'd have your
power steering pump and somewhere up here you'd have the alternator but those two are missing on
this hybrid model that's because it uses electric power steering and there's no alternator because
you have an electric motor that'll do the job of recharging that 12 volt battery. However if you do
look further down there is a serpentine belt connects to the crankshaft to this AC compressor.
Now this AC compressor is a unique one because it's powered off of the belt when the engine is
running but when your IMA system kicks in and you're at idle stop your engine is no longer
running but you still need AC in the car so it's going to supplement it with an electric motor
that's going to turn that AC compressor so you can continue to get AC in your car when you're
stuck in traffic and that's why you've also got this high voltage wire that goes down to the AC
compressor and is powered by the battery pack. Now this on the Honda Odyssey was one of the very
first implementations of variable cylinder management which means that you could run on
these three front cylinders and completely shut off the rear three cylinders so that you could
save fuel especially if you're just cruising on the highway or slowing down to a stop. Now while
the V6 engine is somewhat balanced while driving along driving around on three cylinders alone is
going to cause a lot of vibration and noise. Now to counteract those vibrations Honda is using
electric active engine mounts so you'll notice that there's one engine mount down at the bottom
here and there is actually a plug off to the side which you can turn on and off to change
its damping frequency according to what mode the engine is in. Now in addition to the front mount
there's also a mount down at the rear inside of here that connects to the subframe then you've
got a mount on the side here that connects to the body as well as underneath the airbox and battery
that connect the transmission to the body. And here's a look at one of the active engine mounts
from underneath this one mounts to the subframe you can see the plug located for it over here and
the other engine mount is located at the back of the subframe over here. Over here on the driver's
side you can see the transmission mount to the subframe. Now variable cylinder management was
the cause of a lot of engine failures on newer Honda Accords that have VCM technology so later
we're going to be tearing this engine down so we can see how that works and what's causing those
problems. Now when you pair off variable cylinder management with Honda's regular VTEC system which
I've got another video on how that works linked below, Honda calls it their intelligent VTEC
system. Now in addition to active engine mounts Honda also included active noise cancellation
especially when VCM is enabled and that used the stereo head unit to pump sound through the stereo
speakers in order to cancel out certain frequencies and noises that you don't like to hear. Now
sometimes those noise cancellation modules did fail and then you'd be pumping out random noises
from your dashboard and that's pretty annoying. Now the PCV valve is located right next to the oil
dipstick on the front of the engine. Now since these engines don't have variable valve timing
Honda's still using an EGR system as a pollution control device it's basically going to take exhaust
gases from the front half of the head here and bring them back around to the intake side so it
kind of goes through the engine once more again. Now this is a weak spot on some Hondas when they
do get clogged up you can get a lot of surging. Now the fuel system on the Accords engine is
tail port injected even though this is the hybrid model. You get the fuel line that's going to come
in here and split off to two fuel rails that are going to feed each bank of cylinders. And if you
look closely you can see one of the fuel injectors here where it's going to inject fuel into this
lower intake plenum before going down into the engine head. And now we'll have a listen to the
start of sound. Now taking a look at the hybrid drive system here we've got a three phase synchronous
permanent magnet electric motor sandwiched in between here. You can see the three different
wires here coming in for the three phases. It'll then go through this shielded wire all the way
out behind the seat where the battery and inverter is located. Now this is a mild hybrid which means
that you can't exclusively drive off of electric power alone the way you could in modern hybrid
vehicles. It was mostly made to help with the idle start stop system as well as increase the
power output from this engine while still maintaining about the same fuel economy as
the regular V6 Accord. All throughout the vehicle from the back to the front we have this orange
cable that basically highlights that this is a very high voltage cable and you could get shocked
if you try to trouble it or it gets damaged. Now with the rear seats removed this is where the rest
of the hybrid system lives. Over on this half here is where all the computers are the ECU that
governs the hybrid system as well as the power inverters and voltage regulators. Over on this
half here is the battery it's rather small because it only takes up this half but then again this is
not a battery electric vehicle this is just used for power boost. Now unlike newer battery systems
which are water cooled this one is just air cooled it's got a fan inside of here with a
ducting system that'll blow the air through these vents. I found some non-oem duct tape here so I'm
pretty sure someone's been here before. Now unlike a German car which would use weird security bits
and triple square heads Honda is actually using regular torques as their security fastener for
this battery pack. I like how Honda threats you that you will be killed or hurt. Now with that
cover removed you can see all of the electronics in and behind here. At the top here we've got our
motor driver which is responsible for taking all that power and controlling it into the three-phase
power that the motor needs. You can see that's the line that'll run down underneath the car
with its three phases. Over here we've got the line that'll come in for our 12 volts to charge
our 12 volt battery at the front because this car doesn't have an alternator. Of course you've got
your control unit here to control the hybrid system and your connections here for your high
voltage battery. Now the battery itself consists of 120 cells they look like d batteries each are
1.2 volts and they're the nickel metal hydride type. Now here's your main power switch that'll
turn the entire hybrid system off because we're going to be taking apart this entire thing to see
what's inside and how it works in a future video. Now looking at the trunk of the Accord Hybrid you'll
see that some of the space is taken up in terms of the length and you can no longer fold the seats
but overall you still do have a generous amount of trunk space considering where the battery pack is.
Next up we'll take a look at the Accord's transmission. Now there is an electric motor
that's about 68 millimeters wide that has to be sandwiched between the flywheel and the torque
converter on this hybrid model. As a result they've had to slim down the transmission quite a bit
and kind of push it underneath the battery and the airbox and they had to get rid of the automatic
transmission fluid pump from inside. As a result they use an electric fluid pump to circulate fluid
in the transmission. Now the dipstick is easily accessible from the top here which is going to be
good so you can check your transmission fluid and change it accordingly. Now if you're old enough to
remember a lot of V6 automatic Hondas used to suffer from automatic transmission failure due to
a defect in the design causing the second gear to overheat. Luckily though this one's from 2005
where Honda started to address those issues and getting less and less failures but if you had
anything older than this you were pretty much down for a transmission replacement at some point in
the car's lifetime. Now this car will use the electric motor sandwiched between here as a
starter motor when you're in idle stop mode to restart the engine. However if that system does
fail they do have a backup starter motor which is a traditional style mounted right at the front
of the transmission here. Now looking over here towards the driver's side you can see just where
the engine ends we've got this little piece here which is the electric motor. That's right the
electric motor is only this thick here 68 millimeters and then that'll bolt up to this
slimmer down transmission on this side. Now this is a five-speed automatic transmission similar to
what you would find in a regular Honda Accord. Over here we have the drain plug for the mandatory
fluid changes especially if you don't want these transmissions to burn out. Now this transmission
has a cooler that's built into the radiator itself. You've got one line that brings in ATF over here
and then it comes back out through this line over here. Of course newer vehicles do the opposite
and circulate coolant through the transmission itself where there's a heat exchanger. Now once
the automatic is done changing its gear ratios inside of here it's then going to send power out
to this rear differential which will then go out to the two axles on either side. One thing with
these Honda axles is that they actually bolt into this shaft over here because there's a carrier
bearing and then that shaft is then going to go to the transmission so it's actually not all one
piece. Now what I've seen in a lot of Hondas is that these axles tend to snap right at the location
of this counterweight over here. You see what happens is a lot of water and crud is going to
build up and start corrosion underneath this piece itself and then when VTEC kicks in and gives you
all that torque that you don't really have it's just going to cause this axle to snap. Now taking
a look at the Accord Hybrid steering setup this is an electric power steering which is one of
Honda Accord's first implementations of electric steering. We've got this shaft that's going to
come out of the firewall here to the rack which sits down over here. Now the assist motor sits
over here on the rack itself just above the subframe it's a little difficult to see. Now
looking in from the right side tire rod you can see the connector that goes to the electric power
steering motor which is mounted to the steering rack. Next we'll take a look at the Accord Hybrid's
braking system. Now because this is a mild hybrid and the engine is always on we just have a
traditional master brake cylinder here with a brake booster mounted on the firewall powered
off of this vacuum line from the intake manifold. Now of course if you had a traditional hybrid you'd
probably want to power that with a vacuum pump because the engine isn't always running with the
car. Now the brake lines are going to come from the master cylinder across the firewall over here
to the ABS actuator and then out to the wheels. This will be responsible for anti-lock brakes and
traction control. Of course this is long before stability control was mandated much less any
autonomous braking features. Now taking a look at the front brakes in the Accord things are very
traditional here with just a single piston floating caliper with a disc rotor. Doing a brake job on
this is pretty straightforward with the only exception being these stupid rotor screws that
Honda tends to use. They always tend to strip out leaving the rotor stuck on there and you got to
drill them out. Now taking a look at the rear brakes on the Honda Accord you've got a typical
floating caliper with a disc rotor. Now you'd think that the parking brake assembly is actually
buried in here but instead it's on the caliper. Here you can see where the parking brake cable is
clamped down on the spring-loaded mechanism to squeeze the disc rotors. There's no electric
motors here like in newer vehicles. Next we'll take a look at the exhaust system on the Accord
Hybrid. It's basically the same thing as the regular V6 Accords. You've got a 2-way catalytic
converter at the front here for these banks. The exhaust manifold is integrated into the head
and there's another one at the back here which is a little difficult to see. Here's a look at the
front catalytic converter from underneath. You see the exhaust is then going to come down to this
Y-pipe over here and join from the exhaust coming from the other catalytic converter for the rear
bank up over here and then flow through this flex pipe into another catalytic converter out the back.
Now that exhaust is then going to travel through one silencer then a second silencer and then out
to the back to the muffler. Now that exhaust is then going to come to the back here where it's
going to split off into a dual muffler setup straight out the back of the car. There's no
fake exhaust tips even though this is a hybrid. I'm actually quite intrigued how the front half
of this exhaust system hasn't rotten out yet. It looks like it's either been replaced or
just really lasted a long time. Now we'll have a listen to the exhaust.
Now taking a look at the front suspension on the Honda Accord just like the regular Honda Accord
TSX and TL of this era, this uses a double wishbone front suspension which is actually
pretty advanced especially for a family sedan from back in the day. Even nowadays family sedans are
going with the much cheaper McPherson strut design option. Now the top here we've got this
upper control arm that has this ball joint that ties this long and slender steel steering knuckle
over here. You've got the strut located here mounted to the body at the top and it's mounted
down to this fork at the bottom here which ties into the lower control arm. This fork is here to
go around the axle because this is a front wheel drive. Just like all little Hondas this one's
going to need ball joints soon. Now what I find interesting is the front lower control arm. Now
the back here we've got the small bushing which is responsible for turning or handling and at the
front here we have the large bushing which is responsible for comfort. Usually they're flipped
backwards so that the comfort bushing is at the back and the handling bushings at the front but
instead Honda's chosen to go a little backward with this design. Now looking from the backside
here we've got our inner and our outer tire rods as well as the stabilizer link and the sway bar.
Now I've got an entire video on how to rebuild this suspension including the lower control arm,
sway bar links, inner and outer tire rods and the upper control arm as well as ball joints so make
sure you check those videos out in the description below. Now the bottom here we've got the lower
ball joint which is pressed into the knuckle itself and then we've got the lower control arm
that just ties in with the taper over here. Now because this is a double wishbone design there's
a shock that is mounted over here which means that all the weight of the vehicle has to be
transferred through this ball joint which is going to increase its wear. Eventually these are going
to have to be replaced. Now if you've seen my lower ball joint replacement video it's not an
easy task to get to this ball joint because you pretty much have to remove the knuckle, get the
brakes off, get this lower control arm off and remove the axle in order to be able to press this
out. This is definitely going to be a high maintenance item because it's going to wear out
pretty fast and you should definitely get it taken care of because it's a loaded ball joint
and if it fails it could cause catastrophic failure because it takes the whole weight of
the vehicle. Now unfortunately the wheel bearing inside of here is also a pressed in design so you
can't just unbolt it and remove it. You will have to take the whole thing apart and take it to a
shop press to get it pressed out. Now overall I think having a double wishbone front suspension
on a family sedan is actually pretty cool because that's what gave this vehicle a competitive edge
in handling for its time especially if you compare it to say a Camry or an Altima that had a McPherson
design. The only downside is you've got a lot of extra moving parts here that are load bearing
which is going to mean that you're going to have to pay a lot more on maintenance to replace these
components and a typical family sedan owner might tend to neglect this. I think cost and
maintenance was ultimately what caused the Accord to lose this double wishbone design and competitive
handling edge when it went to the 9th generation redesign. Okay so I'm trying to jack up the rear
and the entire rear rocker panel is so crunchy and rusty. Now the back of the Honda Accord
suspension you'll find a five link suspension which is actually quite unique for a family sedan.
We got our front upper control arms and rear upper control arms here. We've got the rear lateral
link over here there's another lateral link buried underneath here at the bottom and then we've got
our trailing arm over here. Now just like the front having a five link design is going to be good for
handling and that's why these cars handle so well it's just too bad that you don't really see too
many family sedans with a five link suspension at the back here as complicated as this. Of course
the downside to this is each one of these links here has a wear point at the end of it whether
it's a spherical bushing a rubber bushing or an upper ball joint like this and those have to be
replaced at some point. Now unlike the front we do have an aluminum knuckle with a bolted on rear
bearing here so it's pretty easy to swap out the whole hub assembly. Now the shock itself bolts up
with just one bolt up at the top there and then another bolt down at the bottom over here. I've
got a video on how to replace that so make sure you check it out. And here's a look at that rear
suspension from underneath here you can see they've all got different tie points on this subframe over
here and up at the top there and these ones do have adjustable bolts for camber however a common
problem with anything that ages is that these bolts are going to get stuck and seize in the
bushings when you have to replace these arms and good luck trying to get that out. Now one thing
that differs from the regular Accord is that the rear knuckles are made of aluminum instead of steel
which is going to lighten things up a little bit back here just kind of stands out that this is
new tech versus everything else that's rusting out. Now at the back here this piece of rust is
the sway bar this tiny little dinky thing one of the common things is to upgrade this to the one
from the Acura TL just a couple of bolts here at the bushing on either side and the end link where
it joins up over here to that shock mount. Next we'll take a look at the Accord's cooling system
now things are fairly straightforward it's got a simple radiator up at the front here with your
radiator fans surprisingly the radiator fan shrouds are made of metal still we've got our coolant
reservoir over here as well as our upper and lower radiator hoses. Now if you follow those two hoses
we've got our coolant temperature sensor over here as well as a thermostat located over here
which is fairly easy to access just below the throttle body. I guess the most difficult part of
the cooling system to access is the water pump which is located inside of the front half of the
engine driven off of the timing belt. Now here's a look at the cooling system from underneath we do
have a petcog valve here to drain the radiator unlike newer cars where you actually have to
remove the radiator hose to drain it. Now the back here underneath all this rust of what is the rear
subframe is where the fuel tank is located luckily it's made of plastic so it's not going to rust as
fast as everything around it down here. Now the evap canister is located just in front of that gas
tank underneath this plastic shield here. Now while many cars you access the fuel pump from underneath
the back seat since the tank is pushed back quite a bit in the Accord you access it from inside the
trunk through this panel over here. Now overall without a doubt the seventh generation Honda
Accord was pretty well engineered overall they did last quite a long time you can see this one
got over 400,000 kilometers and it starts up and runs really smooth
oh that sounds sick however I think Honda really lost out on its implementation of this primitive
hybrid technology just using an electric motor in between the engine and transmission with a
battery pack just to boost the power of an already powerful engine doesn't really make
sense in terms of the extra four thousand dollars you have to spend on this compared to the regular
V6 Accord especially if you consider you didn't really get much of a fuel savings over the regular
V6 and that it can't really run on its electric battery alone the point of buying a hybrid is
really to save fuel and that's just going to be eaten up in the cost of replacing the battery
especially if you want to own this thing long term. So I give kudos to Honda for making a
really good family sedan for what it is that handles well due to a nice suspension design
a really sturdy V6 engine and hopefully the transmission. Now I'm going to be completely
taking apart this car so we can take a closer look at all the components in the powertrain
and the hybrid system to see how it works. Make sure you follow me on Instagram for more
behind the scenes footage and subscribe for more videos just like this one.
