What's up guys?
We've got a lot going on right now.
Thanks for joining me.
If you want to make a reflex-deflex bow, this video may be very helpful to you.
This is the last video in a tailoring course, a whole series of multiple videos you can
check below for the playlist.
And I've got some sweet things coming very soon.
So sit back, relax, enjoy this long video if you want to make a bow.
If not, I'm coming to you here real soon with what I think you'll like.
So stay shadowproof.
See you guys around.
All right, it doesn't get much more exciting than this.
We're going to start tailoring this bow.
Now this specific one has bamboo on the back with Ipe on the belly.
But any reflex-deflex bow design, whether it be fiberglass, whether it be this, whether
it be just an Osage bow, whether it be any materials, the same concepts are going to
work for tailoring.
So on the whiteboard behind me, I've got some goals and a plan.
Let's go into it.
So I'm going to walk you through kind of my exact process of tailoring and kind of how
I go about it.
The first thing here is we've got our goal.
We've got a 40-pound bow is what we're going to shoot for at a 28-inch draw.
I'm going to look for one 8-inch positive tiller, and that's going to be the starting
point.
And then in the end, when we shoot it, if that needs adjusted for smoothness of shooting,
we will.
And then finally, we've got speed.
I'm focusing on speed on this bow.
We've got thinner limbs.
We've got a really, really hard wood in the Ipe.
This type of bow, I like to focus on speed, and that's how this one's designed.
Then over here, I've got tillering revolutions.
This is just for you guys so you can see how long it takes me.
So the first section is going to be floor tillering to 6 inches of bending.
So this is from not bending at all to starting to bend.
And every time I remove wood and then go to the tillering tree will be one revolution.
From there, we've got 6 inches till the bow is strung.
And so I'm just going to mark this here.
I won't show every single time I'm removing wood, but I will show you the tiller each
time.
And then we'll keep track so you can see kind of an idea of how many times it takes.
So it may be 20, 30, 40, 50, I don't know.
We'll see how many times it takes to get to the next step.
And then from the bow being strung up till we're at 2 inches left on our bow.
So those are the three steps so you can kind of see which one takes the most time and which
one takes the most revolutions of wood removal so that you can use those numbers and be cautious
yourself to know how close maybe you are.
This reflex-deflex bow, I'm going to tiller on the tillering tree.
And then on the D-bow, I'm going to do that on the tillering stick.
So you can see how I would do both of those.
But the first thing to do is to set this up there and make sure the bow is level.
Got this block behind here, got a little play for different sizes of bows.
So I should be able to, there we go, and that's tight.
So it'll be, it'll be pushed this way.
So the limbs won't be running along the wall.
I'm going to step back and take a look at this bow and this, this side over here is
a little bit lower.
We need that up right there.
So we need to add a little wedge on this left side.
So you could use a little piece of wood like this.
I'm going to use some tape so that I can stick it down and then it won't move for the whole
time.
This is one of those things you may not think about doing in the beginning, but if you do
it, your results will be much better.
The other option there is I could have thrown this on the belt sander and sanded this end
down or it would have been this end down and it would have sat better, but a tape is a
little quicker.
There we go.
We are looking even.
And so what I'm doing is I'm looking at this line.
I know my wall is level and so I can look at that line and match it up on both ends
where it's resting because that's the reflex.
And then from there, now when I draw it down, it'll be easier to tell which limb needs to
be removed.
But if it were off, it's going to be a lot harder to see visually which limb needs to
be removed because you're not drawing it down, you'd be drawing it that way basically.
So step one, get it level.
I'm going to center the bow and then I'll draw it directly in the middle for now until
the bow is strong.
And then once the bow is strong, I can establish the top limb or the bottom limb.
If your bow layout allows you to do that, I like to do that more now because even on
a board bow, the string could lay off to one side and that's the side I'm going to
want the arrow rest on.
If you have a specific layout where you've already established the top limb, what I like
to do is always put the top limb on the right on everything I do.
That way it's consistent and I know which one's the top and which one's the bottom.
That's really important, especially when you're getting to the end of tillering and adding
in your positive tiller.
So for me, I just move my pulley around in order to get it in the right location.
Okay, so just like that, I got the pulley directly in the center and then once I get
the brace height, establish the top limb, I'll move it back over to the right because
that's where my fingers will lay on the bow.
So right now, we're hardly bending at all.
So this is where I'm going to take this to the belt sander and I'm going to hog off some
wood.
What I will do is I'll find the thinnest part on the limb, which I think is right here from
looking on it, and then I will mark a line on either side at that thickness and then
go remove down to that line on the belt sander so that I can get enough wood down that it'll
start bending, but I can still have guidance lines and I can check with a caliper so that
I don't go too quickly.
But this is a time I like to use the belt sander to hog off a decent amount of wood.
So I get thinner as I come in.
One thing, if you are measuring, just remember there are nodes and if you measure right on
the node, you're going to be like, oh that's super thick, but I would just move off of
the node about a half inch to an inch to get an accurate reading.
One of the benefits I have is I've built a lot of these bows before.
Here's a finished one.
So if you've ever built a bow before, I always encourage people to measure it and so I'm
like five and a, uh, 550 thou, I guess is how you'd say it, of an inch.
So basically we're half an inch, slightly over half an inch, and then it tapers down
to below half an inch since the limb is tapered, but what I can do is I can mark this bow and
make sure my lines are bigger than half an inch because I need to give myself play when
I'm using the scraper, but that gives me a reference to know how low to go.
And honestly that's pretty consistent throughout other bows.
So here's a 40 pound oak bow and we're at 660 thou, so we're 5 eighths of an inch-ish,
and so this one's a little bit bigger.
Generally the weaker material, the larger or thicker the wood needs to be, but it also
depends on your width.
But most bows are 3 eighths of an inch to 5 eighths of an inch thick if you're in between
a 30 and a 60 pound bow.
So you can just keep that in mind just as a reference depending upon the bow you're
making.
Alright now let's hit this up on the belt sander and hog off some material so that we
can start bending it.
Okay I removed it all on the belt sander, I cleaned it up here with a scraper, and I'm
going to go ahead and put the scale on and start now.
So I'm going to pull it down to 40 pounds and see how far we bend.
So 40's right there and I don't ever want to draw past 40.
So we stopped there and we clearly see we're bending 3 inches, maybe 2 inches.
So we've still got a lot of wood to remove, I need to do what I just did another time.
One of the benefits to doing the floor tiller is that it's really quick to see if you need
to remove more wood, which we definitely do on both of these limbs.
So before I check the bend on this bow I'm going to exercise the limbs here for a couple
minutes and I'll warm it up.
Okay we're making really good progress, I removed quite a bit more wood with the belt
sander and then we're bending about 4 inches now from it's resting state, the limbs are
bending down 4 inches.
And now we're going to head over to the scraper.
We're able to see enough bend now that we can start exercising the limbs.
You want to do this as soon as possible so I'm just pulling it down to 40 pounds and
I know the limbs are only going down 4 inches, but as soon as possible you want it to start
remembering the new memory because you have removed wood.
The primary goal right now is to keep the bottom and the top limb bending at the same
distance and an even amount of stress throughout the limbs.
We want that tiller to be as even as possible as soon as possible so that if we have a draw
length of 12 inches or 14 inches but our tiller is even, then we just have to evenly remove
wood off both sides and it makes the second half of tillering go much quicker rather than
having to correct and over correct back and forth.
So the goal right now is to measure often with calipers for me, to look at it on the
tillering tree, to check for limb twist, and to make sure we're keeping it as even
as possible.
With a reflex-deflex bow, we want the stress to be distributed evenly throughout the limb,
the same as we would with a D-bow.
The difference is the shape of the bend is going to be different.
On a D-bow we could throw those circles up there and you can see the arc in the limb
is even and that's because it's a flat bow and then we're bending it and so it's even.
But a reflex-deflex bow, it's bending backwards the other way and then part of it's bending
down because it's got a reflex and a deflex in it.
So as that limb is curved, as that limb is curved there, we want it to bend evenly from
this setting point because if we made it curve like we would a D-bow, this part right here
in the middle would have like no wood left and it would break in the middle there.
So it's kind of going to follow this shape, if that makes sense, for it to bend and as
we move along you'll be able to see the shape that I'm looking for.
It's kind of a trained-by-the-eye look, but the benefit to a reflex-deflex bow is that
if you pull it off it's a very smooth shooting bow.
So it's a fun challenge on the tillering because it is different and a key to keep you on track
is to follow the thickness of the wood and you want a slight taper from the handle down
to the limb tips.
And I know it's not much bend yet, but it's actually looking really good.
So I'm looking at both limbs, seeing if the left and the right are bending pretty equal,
which they are, and then secondly I'm looking for action, the same amount of action throughout
the limb.
So this should bend as much as this.
This, since it's curved back up, will still look a little weird because it's not going
to be, the tip's not going to be all the way down.
So mentally you can separate the limb into three parts.
You've got from here to here, so it's a pretty straight section.
And so I can focus right there and see how that's bending, and then from here to here,
which is going to be a very curved area.
So that's the difficult part, and then we've got from here to the limb tip, and so on.
And so we've got about one, two, three sections, and those three sections you want to train
your eye to look at individually, and that'll allow you to determine if that section's bending.
If you try to look at the full limb at once it can be kind of confusing, but I can check
this first eight inches and then look at the opposite side for the first eight inches and
see if there's action.
Look for action in that area.
If there is not action, then that's probably the area you want to remove.
Same thing here.
We want to look for action in the middle.
The middle could have the most action, but since there's a lot of curve right there,
it could look like when you pull it down there's no action.
So that's why you kind of really need to mentally separate the different parts of the limb.
And because it's a reflex-deflex, the gizmo's going to be pretty much useless because it's
just going to mark this middle section the whole time because we've got the curve in
the bow already.
So this isn't the tool for the job.
We're definitely going to use our eyes, and I'm going to go ahead and use a Sharpie.
I'm going to look for action in comparison on both limbs and mark where I think we need
to remove wood the most.
So I'll pull it down and hold it at that 40 pounds for about three to five seconds.
That way I have enough time to look around.
And from what I'm seeing, there's a decent amount of action here, but on this side it
doesn't match it.
So let's move into that middle section.
And the same thing with the middle section.
There's a decent amount of action here, but over here we need more.
And then near the handles they look about the same.
So from here I know where to remove wood a slight bit more off this outer edge on that
limb, and then since the limbs are bending equally, we're still going to remove wood
off of both sides, and we're going to make that equal.
But this limb, since it's bending more equally than that one, I can just remove wood equally
over the whole limb.
On this limb, I need to remove more on the outside because it's not bending as much there.
So before I check the bend on this bell, I'm going to exercise the limbs here for a couple
minutes.
And I'll warm it up, and I'll pull it to 40 pounds and hold it for a second or two.
And repeat.
I've kept the corners of the bow square so I haven't rounded them over, and I primarily
do that because that makes it easier to take readings with calipers to look for a limb
twist.
So once we do this and see where we want to remove wood, we'll go put it in the vise and
check for a limb twist real quick.
That way we can proactively take care of that if anything looks like it'll happen.
Or before anything looks like it'll happen.
We've got a really, really good start.
Again, you've kind of got to make this your own.
So I like to use these calipers to check the limb twist, but you don't need calipers.
You can absolutely pull the tape measure out, line up the bottom line of one of the inches,
and see how close you are.
And it's close enough that you can make a very, very good bow that way.
But this side is a little bit thicker.
So I'll mark the side that's thicker and then go ahead and take that off first to make these
two sides even.
And then, technically, the two ways to do this is if you can see how far off you are,
with one of your shavings, you can actually measure it with a caliper, calipers, and get
your reading.
And then from there, you can know how many scrapes you'll approximately need to get that
much wood off.
If you like going technical, you can do that.
And so for me, it's about four thousandths of it, four thou, basically, or five thou.
And so I can know that if I need to get, let's say, one tenth of an inch off, or a hundredth
thou, I need to do twenty scrapes to get that off.
That is technical, but if you like that sort of thing, it can be helpful to be precise.
And if you're not interested in going technical like that, don't at all.
Just mark with a sharpie, do some scraping, and test, and just look, and go intuitive
as you want.
There's not one method that's better than the other.
It comes down to attention to detail and practice, and the method that each individual likes
to do.
I kind of find myself in the middle, I mix both, or I mix a bunch of different methods
together, because for me, if the math checks out, if with my eyes it checks out, the more
things I can check the tiller to, the better result I have, and the quicker I generally
find a problem.
Okay, I think we should be getting close to forty pounds at six inches.
I'll exercise it a bit first, and then we'll take a look.
We still got a lot of wood to remove to get to six inches.
We are just about three and a half, four inches on the pole, so let's go again.
Alright, so I took more wood off, I'm still being fairly aggressive, and now we are pulling
five inches at forty pounds.
So we're in that four to six inch mark, and all that's going to tell me is to switch my
brain a little bit to start being just a little bit more careful, and what that is, is just
to remove less wood for the next time I check.
That way it's easier to have control.
I'm pulling it about five inches.
When I get to pulling it about ten inches is when I will string the bow up.
Ten inches at forty pounds.
So we've got five more inches to go before we can get it to brace height.
I'm going to continue as we've been doing, and I'll show you the tiller each time I come
from removing wood, and then I'll catch back up with you when we're at brace height.
And I forgot to tell you, this is where we really start using a sharpie to mark evenly
where we're going to remove wood, take the sharpie line off, and then come back.
I've been doing, I've been marking with a sharpie, but once the sharpie line's gone,
I've been continuing to remove a decent amount of wood, so we're dropping that down to just
removing the sharpie, which is going to be about ten strokes with the scraper.
Alright, I've put a tighter string on it.
What you can see when the string's running straight, it's not directly down the center,
it's running further to the left.
So I'm going to make that my side, where I'm going to have the arrow rest, dubbing this
the top limb.
So on the bow, I'm going to give myself a T on the top limb, and I'm always going to
have that to the right.
One of the really good things about putting a string on it is, yes, you can figure out
your top limb if you haven't yet, but secondly, you can line the hook up with where you shoot
the bow, so you can move it back over to the right if you need to.
But I did have to flip those sides, so I'm going to take the tape off and I need to re-level
it for it being flipped so that it's not off.
Right now you can tell it's quite off, it makes it look like the right limb's bending
much much more.
Okay, I just got a string on the bow for the first time, and you'll see that the bend is
different now than it was before the string's on, and that's because with the string on
now, it's pulling this in more, where with a loose tillering string, we're pulling down
more.
So it does change the angle a little bit, and that's why you'll want to get a string
on it as soon as possible.
Alright, this is where we're at so far.
The first step took me five times to go back and forth between removing wood and exercising
the limbs, and then after it was bending about six inches, to get it strung up, took me ten
times of removing wood, and so now we're starting here, we'll see how long it takes to get to
the finished bow.
And by the way, this has taken me like two hours so far.
Okay, what's really interesting right here is how much of that reflex snapped out of
this bow when I got it to brace height.
I wasn't expecting that, but that's looking more like a G bow compared to this one.
So that means this middle area is stronger on this one.
Alright, so here's the deal.
I was trying to figure out what to do because I screwed up a little bit, and I'm just going
to show you how I'd work my way out of this problem in case it ever happens to you.
So basically, I'm teaching a course on how to make a bow and what not to do, but it's
taking a long time because I'm filming, and so I tried to skip a few steps and jump the
process.
In other words, I was just scraping too much wood at a time, and I got it bending too far
before I put the string on it, and that's why when the string went on, I was like, what?
What's going on?
And it's like, oh yeah, you went too fast.
So hopefully you have the self-control not to do what I just did, but here the bow is,
and the top limb is bending more than the bottom limb, so we've got to just work on
the bottom limb.
First step is to make the both limbs bend evenly.
Right now, if I take the tape measure, we've got seven and seven-eighths, and we got seven
and a half on the bottom.
We want that closer to an eighth-inch difference instead of a half-inch difference, so we need
to remove and exercise these limbs, but especially off the bottom one first, so let's do that.
So my biggest concern isn't if I can get this tillered looking good, shooting well.
The biggest concern is if I can do that before we hit 40 pounds at 28 inches.
Sometimes if you remove too much wood, like I did here, you'll get to that 28 inches,
and you won't be a good tiller, and you'll already be at 40 pounds, and so you'll want
to remove more wood.
That way it doesn't create a problem over time, but you're going to end with a lighter
poundage bow, so that's what we're fighting against now.
Because the limbs are so imbalanced, I'm not going to overdraw it, so I'm only drawing
to 30 pounds right now, because that right limb is just bending too much compared to
the left, and I'm just going to exercise it at 30 pounds for this round and go remove
some more wood before I pull it back to 40 pounds again.
Now the nice thing once you have a string on it is you don't have to take the string
off to remove wood.
I'll show you how.
There's two ways I use this scraper.
The first way is just normal like this, which is totally fine.
You just don't want to nick your string.
So another way is you can turn it this way, and that's why I'm wearing gloves, because
you get this sharp angle, and you can poke yourself with the scraper.
But at that angle, you can also scrape, and then you avoid ever nicking your string.
It's a safe, and it's actually a really easy way to remove wood.
See, I've got to quit thinking about the film, and I've got to focus on this bow for a second.
Breaking all my own rules.
They're my rules to make a good bow.
You don't have to follow them.
Just helps.
As we get further along, I'll hit the corners with some sandpaper just to take that edge
off and make it nice and smooth.
I like to just do a few quick pumps to get the limbs moving again.
That's starting to even out.
I'm not sure if you can tell, but we're getting closer here.
I'm just grabbing a string from my reject pile basically, but what I would normally
do is just shorten that tillering string and keep using your tillering string until the
bow's done, and then measure that tillering string and either make or buy a string that
is that length of the tillering string.
But since I have so many leftover and old strings, I always have one that's the right
length.
Okay, this is kind of interesting because this is real time, like, what's going on here?
So what is also very interesting about this bow, there's two more things that I've went
into play.
One, is that the original reflex in this bow was very minimal.
I'll probably throw up a little bit of video here, a little shot of the beginning bow,
but it was very, very minimal, causing this to end up to tiller more like a D-bow than
I expected.
The second thing is, this is a wood bow, and I've been tillering a lot of fiberglass bows
recently, and the fiberglass doesn't set as much, it doesn't have string follow as much.
So with that being said, this one's going to be a finished different shape than this
fiberglass bow.
Even though they're both reflex-deflex bows, this one is much, much more extreme.
As you can see, it's held that curvature, and I've left this bow strung for over three
months as a torture test.
Now I shoot it often just to test it out.
This one right here that we're making right now, you can see it's much more like a D-bow
than this one because it's lost some of that reflex.
I'm going to unstring this, and I'll show you how little it's reflexed.
So there is the unstrung bow.
There's a little bit in there, but I mean, it's less than an inch going either direction.
So it's almost unfair to call this a reflex-deflex bow, so I'm going to have to do an extreme
version of a reflex-deflex bow later on, but I want to keep this in the course just so
you can see kind of the process and how I've run into problems, but I'm still going to
try to make a really good bow with this one.
So I don't want to overcomplicate tailoring, and as I go more in depth, if something's
confusing, if I say something that makes you feel like it's so complicated you don't want
to start, forget everything I say and just start.
Okay, I got the string on it now.
We got a really good brace height, actually.
I even marked the string with duct tape so I know where to put the hook each time.
So check out this bend with me.
Okay, so right there's 20 pounds at 15-inch draw, 30 pounds at a 19-inch draw, go to 30
a couple times, okay, we're going to go to 35, 35 pounds at the 21-inch draw.
That upper limb is bending great.
The left limb needs a little bit off the middle.
Right down to 40 pounds, positive tiller slightly, okay.
All right, so we're back on track.
I've got a positive tiller by one-eighth of an inch.
Still need to remove a little bit more wood here on the top.
It's a 40-pound pull right now at a 24-inch draw, I think it was.
So we've got four more, four to five more inches to draw.
So only using a pencil now, going to continue to remove wood, make very small changes because
we are so close to this being done.
Okay, so this is 40 pounds now, right there at 20, 23-inch draw.
I'm going to give this a break before I finish it out because I've been up a long time.
And I know I'm prone to make another mistake easily if I don't give it a break.
So often what I like to do is just leave the bow strung, sitting right there.
That's going to have the bow under stress and I'll leave it for 30 minutes or so.
And if it has not set into its final position, that'll definitely help it do so beyond exercising
the limbs.
Okay, it's been a day or two and I've got some fresh eyes to look at this.
So this is the reflex-deflex bow here on the right we're working on.
And here's a finished reflex-deflex bow on the left.
And you can see that they're much different in their bend, which will change the tiller
just a little bit.
So this is how tillering goes very often.
You think you're doing one thing and then you realize you need to change.
So the difference between this tiller and a debow is going to be the very middle of
the limbs just aren't going to bend quite as much.
So if we have an even tiller throughout, this section right here in the middle of the limb
shouldn't bend quite as much as it would on a debow.
So it's going to maybe look like the right and the left are bending slightly more.
In other words, if you use the tillering gizmo, it's going to mark the middle and not the
sides.
But that's okay because what we talked about earlier, you want the same action throughout
the limb.
That way it's distributing the stress evenly.
With this slight deflex down here before it comes up on the reflex, we need this middle
area just to bend a little bit less when you're pulling it.
That's what it's going to look like.
It's bending less when actually, since it is coming up, it's bending the same.
So it's just going to be slightly different.
And this is how deflexed bows work.
So deflexing coming down from the handle, that's the deflex.
The reflex is coming back up here.
The reflex is quite easy to tiller because it's at the end of the tip and you just don't
use it near as much.
It's easier to tiller, but the middle is where it's a little bit confusing.
But you can see from this bow to the fiberglass bow I was showing you an example of that I
made, you could have a reflex deflexed bow anywhere on that gradient or even further
and that's going to change how much it's bending there in the middle.
So enough talking.
Let's get back to tillering.
We're getting real close here.
I need to start fine tuning this and getting the tiller nailed in.
So I've got this marked with a pencil where I'm going to remove wood.
I just want to show you how little of wood you need to remove to make a difference.
We're at 24 inches, so we only need two more inches before we're going to call it done
and do the final sanding and shape the handle.
So when I mark the part that I want to remove with a pencil, you probably can't see it,
but it's from here to here.
When I'm removing wood, and right there that's literally at four to five scrapes,
and then just grab some sandpaper, smooth it out, and that'll change the tiller at the
end.
The closer to the end you get, that's why we go less aggressive is because there's so
much, there's such a little wood left.
It changes the tiller really quickly.
35 pounds.
Get it moving.
And then we'll go snap that.
24 inches still.
And now let's go to 40, 25 times.
All right, there's 25 times for us.
So I'll go again, pull it to 40.
The limbs are bending really good relative to each other.
Still that slight positive tiller.
So just going to remove a little bit of wood off both sides.
That way we can continue with that positive tiller.
Okay, so we're at 26 inches.
Made super good progress.
Looks great on the computer.
I like to do that near the end to double check.
My eyes aren't deceiving me.
Everything's looking good.
So now it's time to shape the handle.
Once we get the handle shaped, we can shoot it.
And if we like how we shoot it, we'll be able to do final sanding, sign it off, and have
a great bow.
I like to cut my arrow rest on a curve.
That way the arrow only touches right here at the very top.
So I just cut it with a hacksaw blade.
Any wood saw with fine teeth is great.
So I'll just cut down the arrow rest and then I'll chisel out the side for a little sight
window right here.
I went to the center, came up an inch and a quarter, and that's where I do the arrow rest.
Okay, we got the handle shape good enough to shoot it.
And the method I like to use is to check it on the tillering tree and if it looks perfectly
fine to me, then I can shoot the bow.
And if it feels fine, call it done.
Do final sanding and final shaping of the handle and you're done.
But if it doesn't feel great when you shoot it, recheck the tiller, exercise the limbs,
give it a little bit of time, and you might find the problem on why it's not shooting
good.
But I always like to shoot the bow before I officially call it done.
Okay, I shot the bow a few times and it's actually feeling really good.
So the way I like to finish it is just go to 120 grit sandpaper and then move up from
there to 340 or whatever you want to do and get it as smooth as you like it.
And the bow is finished once you get the handle shaped like you like it.
But that's all the tillering right there.
The rest of it's just making it look pretty, but it's a functional good bow right now.
So I did a total of 26 revolutions.
So we did five from floor tillering to six inches of bending, so barely bending at all.
And then it took us 10 more revolutions to get to a strong bow.
And then lastly, we did 11 up on the finish.
Now, that could be double for you on your first bow.
I guarantee I did at least 50 the first time, but I did 26 here.
And I'm going to show you real quick every single one from start to finish so that you
can see how the tiller changed over time.
Check it out.
And there you have it.
That's the method.
Those are the methods, so to speak, that I use when tillering.
If you have any questions about the Reflex Deflex Bow, let me know, and I will make a
video for you, or I'll answer you in a voice message or a text.
So just ask or comment below, and we'll get your question answered.
Thanks so much for watching.
And with that, I'll see you guys around.