A large syringe type water toy as a basis for storing potential energy was successfully used to drive a small cart across the floor for about 200 feet. By pulling the plunger out on the toy syringe, a vacuum is formed in the empty chamber and atmospheric pressure trying to equalize the pressure inside the tube drives the plunger back in again with a force of approximately 11.5 pounds or 51 newtons. As the first prototype to test the concept, the cart was made rather large and heavier than needed but still managed to combine drive and coast for the length of our school hallways and gym floor. Minor efforts were tested at changing the mechanical advantage of the drive but still needs to be refined further for improving distance or speed of the cart.
Hello, I'm Bruce Shaney, and today in Homemade Science, I thought I would share with you
my latest project.
In this case, I'm trying to build a car that's powered using energy stored from atmospheric
pressure.
Now, originally I saw this idea from Tom Stanton on his YouTube channel, and in his case, he
used syringes.
Now, in our case, instead of using syringes, I'm going to go a bit large and use these
water squirters.
Now, these actually work fairly well.
You simply draw the water in, and then give it a good push, and it shoots at a pretty
good distance.
In this case, we're going to seal the one end and pull back on that plunger, and it
feels like I'm pulling back on a gigantic spring.
The first step is to lock the tube onto the car itself using these blocks, and then before
I use it, I'm going to wrap a second layer of plastic around it to keep atmospheric pressure
from collapsing the tube wall.
All right, I think I'm ready to run some trials.
Now, the first thing I need to do is seal the front end of this tube.
To do that, I put in this little plastic plug and hopefully get a good seal.
Next, I'll pull the plunger out slightly and attach the string to the back axle.
It takes about 14 turns to get that plunger fully extended.
Our first runs look very promising, about 125 to 150 feet before we had to stop it.
Trying it in the gymnasium gave us about 170 feet before we'd have to stop it.
When I first started testing these, I was quite surprised by how much energy I thought
I could store by simply pulling back that plunger.
Of course, the length of it would require that the car I made would be fairly large.
It's also a bit heavy.
It weighs in at about 7.5 pounds, or about 3.5 kilograms.
The potential energy to drive the car is actually the result of creating a vacuum or empty space
inside that tube when I pull back the plunger.
The atmosphere tries to push that plunger back in again, with a pressure equal to about
14.7 pounds per square inch.
The plunger is slightly smaller than a square inch, so the exerted force is somewhere around
11.5 pounds, or 51.2 newtons.
This force then applies a torque to the axle, which powers the car for about 32 feet.
After that, it's coasting until we run out of room.
Of course, some runs were better than others.
Once in a while, the car thinks it's a rollback toy.
Ready?
Yep.
And this is what happens if we don't have a good seal at the front of that tube.
Now, with a good seal, it does take quite a bit of effort to pull this plunger out,
and that force should be consistent for the length of this whole tube.
We can test that using a simple spring scale.
We checked the force at various distances and found it matched our calculations of a
little bit over 51 newtons.
So the force being consistent for the full range gives us a nice, smooth acceleration.
So far, we've been running this car with the string wrapped directly around the axle.
Now I want to try a slight change to it.
Currently, the axle has a diameter of 5 sixteenths.
I'm going to add a sleeve on it, which is going to increase it to 10 sixteenths.
We were looking at changing the mechanical advantage and wanted to see if this would
improve its performance.
The additional torque was enough that it caused the wooden wheels to spin on the gymnasium
floor.
A problem that we could easily resolve by adding rubber bands to the rear wheels, and
that gave us enough traction.
We found it did make the car slightly faster, but also broke the rear axle after a few runs
due to the added stress.
We also found that it slowed down faster.
Up to this point, the car's been running in a straight line, but the front wheels are
adjustable, so I thought I'd turn them and see if I can get the car to go in one giant
circle.
Looks like it just made it.
Well, for the first prototype, I think we had some pretty good runs with it.
Now it's time for some improvements, and if you have any ideas, I'd love to hear them
down in the comments below.
I will keep you updated on the progress of this, and as always, I want to thank you for
watching and come back and see me again.
Okay, bye!