Today, on Workshop Edits, I'm building an end grain cutting board that has a coffee pour over station included, inspired in part by Ben at Homemade-Modern, all made from scrap pieces of African Mahogony. Hope you like!
➤ Check me out on SOCIAL MEDIA! FACEBOOK: facebook.com/thecuttingbored INSTAGRAM: instagram.com/thecuttingbored
Thanks for watching! Zach aka TheCuttingBored
What is going on guys?
Welcome to another episode of The Cutting Board.
Today I have a few scrap pieces of African mahogany wood
that I think I want to convert into some sort
of portable breakfast station,
which would include a end grain cutting board section
as well as a coffee pour over station.
Now this design is not exactly my own.
A guy named Ben over at Homemade Modern
built one of these a long time ago.
However, his was a lot more simple in nature
just given the design of his channel.
He's often using simple materials
that you can get at your local hardwood dealer
like Home Depot as well as a select set of tools
that are readily available to the average DIYer.
However, I've never done an end grain project before
and I think I have the perfect amount of materials
to actually do that.
So I'm really excited to get this started.
I think it's gonna be awesome.
So let's get to it.
So to start off, I cut all of my strips along the grain
to 1 3 8 inches.
And if you want any more details
about any of my cuts or measurements,
make sure you check out the written article
that I will link in the description.
Now this can also be done on a table saw.
I just don't have one currently
and since my pieces were only nine inches long,
doing repeat cuts on my miter saw worked just great.
Next up, I laminated my pieces together
in increments of six.
And looking back, I might have done seven or eight strips
just to make my final cutting board wider.
Now for this project, I am using Titebond II glue
which is an FDA approved food safe glue
as well as waterproof.
Now you can also use Titebond III
if you have that laying around.
And before tightening everything up,
I just went in and squared up the sides as much as I could
as well as double checked everything
was as flat as it could be.
Scrap pieces in a mallet work great for this.
Also, I didn't have enough clamps long enough
for this glue up, but using two pipe clamps connected
actually worked out super great for this part.
The next day, I planed all of my pieces down
along the grain.
Now I know the manual says don't plane
anything under 12 inches, but the real goal
is just not to plane anything down shorter
than the distance between the two rollers of your planer.
Otherwise, the wood can get stuck
and cause all sorts of issues.
I took light passes on my pieces
and everything planed down just fine.
I then went back to my miter saw
and cut all of my pieces to one and a half inches
giving me 25 total strips.
I then laid out all my pieces rearranging a few
to help mix up the grain and then rotated them 90 degrees
so that when I glued them up, everything would be end grain.
Now, cutting boards are not the place
to be stingy about glue, so make sure you use
a liberal amount and spread it out well enough
to cover all of your surfaces.
Now, once again, do your best to keep things flat
and straight so that when you go to clean up
your final piece, it's much easier.
And you can actually go back and wipe off
some of that excess glue after a few minutes
with a damp cloth.
That makes cleanup easier as well.
So these things finished drying
and I'm a little disappointed with how flat they came out.
You guys probably can't tell from this angle.
And I think things just slipped
while I was tightening them up.
I'm actually, look now, it's not too bad.
But it definitely could be flatter
and it'd be easier for finishing.
So I think what I'll do next time probably
is just test out the method where you clamp
a piece of wood on the top and bottom
so that as you tighten things from the side,
the pieces can't move up and down.
I can definitely fix it.
It'll just take a little bit longer
than I think I expected.
But I guess you live and you learn.
Now there is a lot of controversy
in the woodworking community about planing and grain.
Now being my first project,
I didn't want to risk destroying everything.
So instead, I went ahead and cleaned up everything
on my stationary belt sander.
And as Johnny from Crafted Workshop puts it,
do whatever you feel safe doing.
I am not responsible for your woodworking decisions.
Just be safe in your craft.
I can also clean up all of my sides
as well as round over the edges lightly.
Now a router will work really well for this
if you're looking for a specific type of edge,
like a chamfered edge, for example.
But since I wanted just a rounded edge,
doing this on the sander worked fine.
I then could finish out the board
with my orbital sander at 120 grit
and then final hand sanding at 220, 320, and 400 grit,
including a wet sanding at 220,
which I did in order to raise the grain.
That way, when this cutting board got wet down the road,
the grain wouldn't raise and become rough again.
Then it was time for oil,
and I'm using a food-safe mineral oil for this project.
And this is clearly the best part
about making a cutting board.
Last up, I could construct and assemble my pour-over station
and I used black pipe for one set
and galvanized pipe for another.
And my design only actually requires these five pieces,
which I think cost me about 14 bucks at Home Depot.
I then could lay out, mark up, and attach the pipe
to do one end of the cutting board.
I pre-drilled everything, screwed it in,
and then gave everything one last hand tightening
before screwing in the pipe.
And then I was done.
Well, this thing came out great.
I'm really, really excited with how awesome this came out,
especially as a first end grain project.
So I still need to get a funnel to put in this
because you put the funnel in,
then you'll put the coffee filter in,
and then you'll put the coffee grounds,
and then in goes the water,
and out comes the coffee underneath here.
I'll put a link in the description
to the one that I cooked.
It's the same one that Ben from Homemade Modern had for his.
It's like 10 bucks on Amazon, it's perfect.
But other than that, as a first end grain project,
I'm pretty happy with this.
I think my miter saw blade is crooked,
maybe by like one or two degrees.
There's like just an ever so slight slant,
ever so slight slant,
in my cuts now that I'm noticing it up close
now that it's finished.
I'm gonna have to look into that.
I feel like I need to end this video
with me doing some sort of epic Alex Steel
cutting montage after I created something awesome.
I'm gonna go check and see if I have any fruit to cut.
Okay, bad news.
I don't have any fruit to cut,
so instead of ending the video
with me going on a crazy cutting spree,
I'm just gonna say thank you for watching the video.
If you enjoyed it, please subscribe to the channel,
and I will see you guys next time on the cutting board.