For more info contact Diamond Pacific : (760) 255-1030 or message me in the comment section of any of my videos
The Pulitzer Opal Technique Ethiopian Shewa Province Opal Stabilization The goal of treatment is to remove all of the water and replace it with epoxy resin. You must use Hxtal Epoxy. It is the world’s best epoxy and dries crystal clear and is very strong. It is used by museums to restore artifacts and art work. HXTAL IS EXPENSIVE. If you do not use it, I don’t believe that you will be successful. In order to do this, you need to replace the water with something that mixes with water, but also mixes with epoxy resin. Acetone is that “something.” 1. Never let Shewa opal dry out or it will be ruined. Acetone is the fastest drying liquid at room temperature, so be very careful. 2. Take water soaked Shewa opal, wipe off the excess water and put the stones in 100% acetone. 3. After about 12 hours at room temperature, the water in the stones be fully mixed with acetone. The acetone is then NOT 100% any more. 4. Repeat this step 3-5 more times. Remember that the goal is to reduce the amount of water in the acetone. Epoxy does not mix with water. 5. The more acetone in the container, the lower the concentration of water, so use as much acetone as your container will allow. 6. Pour out acetone out and immediately pour the Hxtal resin in. Completely cover the stones, then add about an extra inch of resin on top. 7. Heat resin to 180° F for 3-6 days. For stones thicker than one inch (2.5 cm), as much as 7-10 days may be necessary. a. I personally use a vacuum oven, but honestly, I do not believe that vacuum is not necessary. 8. Take out of oven and let cool to room temperature, preferably 65-70°F. 9. Pour out resin and wipe excess off of the stones 10. Paint thick layer of hardener on stones and place on flexible plastic sheeting (Epoxy will not adhere strongly to plastics). Zip lock plastic bags work fine. 11. Place stones in spot where they are in the 70°s for 4-6 days. The lower the temperature, the more slowly it will harden. For thick stones, I believe that a temperature of 60-65° F for up to 10-12 days may work better (I have not tested this). 12. You may wipe the excess hardener off, then place the stones in a place at 85-95° F for 3-4 days. Heating cures epoxy much faster than at room temperature 13. After curing, there will be excess hardener on the stones. It is best to wipe this off with cloth. Ethyl or Isopropyl alcohol (95-100%) may help remove the residual hardener. (Tested, but not proven.)
First time using my Dremel to polishing rocks I found at Goat Rock beach in Bodega Bay, CA. I using some sanding bits that I got from Amazon with a grit of 50 to 10,000. I used my Dremel 4000 at a speed of 10 and connected my shaft to make it easier to work with.
It took all of my willpower not to cut this agate in half! In hindsight I made the correct decision in deciding to tumble it.
Here is some info on some of the burs I like to use to polish my rock carvings and jewelry. #Jewelry #polishingrocks #dremelcarving #lapidary #rockhounding
http://www.TanzaniteJewelryDesigns.com -- Find out how to tell if your tanzanite is real or fake. Steve Moriarty discusses the tools and techniques used to find out whether a gemstone is actually natural Tanzanite. He goes through the imitations that are sometimes confused with tanzanite or unethically sold as Tanzanite. There are currently no synthetics available, so he shows you how these tools will rule out certain gems, and ultimately giving you an answer to whether a tanzanite is real or fake. You can purchase the equipment you need to decipher if your tanzanite is real or fake for $150.00! Also available to see in person at Moriarty's Gem Art Store at 126 South Main Street, Crown Point, Indiana. We're located in the hub of Northwest Indiana on the downtown Square. #Tanzanite #RealorFake #Gemstones
Growing a real opal into a cuttable gemstone!!!! Embark on a journey a year in the making as we unveil the complete process of growing opals from scratch and transforming them into breathtaking gemstones! In this captivating video, we'll guide you through every step of the mesmerizing journey, offering valuable insights and expert tips along the way. Whether you're a passionate opal enthusiast or a curious beginner, this video offers a comprehensive guide to both opal cultivation and cabbing techniques. Get ready to be inspired and amazed as we explore the captivating world of opal growth and transformation. Join us on this extraordinary journey and discover the magic of growing opals into exquisite gemstones. Don't miss out on this immersive experience – watch now and unlock the secrets of opal cultivation and cabbing! Don't Try This at home! Do not attempt this at home. This video is for entertainment purposes only. Results may vary, and we cannot guarantee your outcome will match ours. Certain parts of the opal-growing process have been intentionally omitted to protect proprietary methods. #OpalGrowth #GemstoneTransformation #OpalCultivation #OpalCabbing #LapidaryArt #OpalEnchantment #JewelryMaking #GemstoneCrafting #OpalJourney #OpalMagic #OpalLovers #GemstoneLovers #LapidaryTechniques #OpalFormation #OpalSecrets
Opal is famous for its shifting rainbows, but the science behind those colors is even stranger than the stone itself. One of the world’s most recognizable “crystals” isn’t technically a crystal at all. Opal is a hydrated mineraloid made from silica and water, and in precious opal, microscopic structures interact with visible light to create the extraordinary phenomenon known as play-of-color. In this episode of Crystals Explained, we explore the geology, optics, history, folklore, and symbolism behind opal—from Australian black opal, boulder opal, Mexican fire opal, and Ethiopian hydrophane opal to synthetic opals, doublets, triplets, and some of the most extraordinary specimens ever discovered. We also travel much farther back in time. At Lightning Ridge in Australia, fossils from the age of dinosaurs have been preserved in opal. Dinosaur remains, ancient monotremes, and other organisms can survive as objects that are simultaneously part of the fossil record and part of the gemstone world. Along the way, we explore why red play-of-color is so highly prized, how some opals can absorb water and temporarily change appearance, why fire opal doesn’t necessarily contain rainbow colors, how opal acquired its reputation for bad luck, and why Queen Victoria helped challenge that superstition. Finally, we look at opal’s place in modern metaphysical traditions, where it has become associated with creativity, intuition, emotional expression, transformation, and amplification. Across geology, optics, paleontology, history, and folklore, the same idea keeps appearing: What looks unpredictable from the outside may be governed by an extraordinary hidden order underneath. Welcome to Crystals Explained: Opal — The Stone of Hidden Order. If you enjoy exploring the science, history, folklore, and symbolism hidden inside familiar crystals, subscribe and join us for the next episode. #Opal #CrystalsExplained #Gemstones #CrystalScience #Geology #OpalJewelry #BlackOpal #AustralianOpal #CrystalCollecting #Mineralogy #Gemology #Fossils #CrystalHistory #Crystals #ScienceDocumentary
Want to learn how to tumble rocks and turn rough stones into stunning shiny gems? In this complete rock tumbling tutorial from UpRockNerds, I show you the entire step-by-step process using both a Harbor Freight rotary rock tumbler AND the Raytech Tumble-Vibe 5 vibratory tumbler. Packed with pro rock tumbling tips, hints, grit ratios, cleaning tricks, and common mistakes to avoid so you get mirror-shine results every single time! Fun Fact: Rock tumbling is a modern fast-forward of what rivers and oceans do naturally over thousands of years to create those smooth, shiny beach stones we all love to hunt for! Timestamps: 0:00 Intro 0:25 Picking Rocks For Stage 1 0:45 Stage 1 Rotary Tumbling - Weeks to Months 9:25 Starting The Vibratory Process Stage 2 - 2 Days 22:45 How to Clean The Bowl 26:00 Vibratory Tumbling Stage 3 - 3 Days 33:25 Vibratory Tumbling Stage 4 - 2 Days 37:45 The Final Burnishing Process 39:30 Final Thoughts And Conclusion Pro tips you’ll learn in this rock tumbling for beginners guide: • Exact grit amounts, water ratios, and barrel loading for both rotary and vibratory stages • Why the Tumble-Vibe 5 excels in polish stages and how to get perfect action • Cleaning tricks between stages for brighter polished rock • Time-saving shortcuts and beginner rock tumbling mistakes to avoid • And Much Much More If you’re into rockhounding, minerals, lapidary, or gem making, this is the ultimate how to tumble rocks and how to polish rocks tutorial you’ve been waiting for! UP Rock Nerds Links. We appreciate your support :) → Rock Nerd App - Your Rock Hunting Companion - http://www.RockNerd.app → Tumbler Buddy - Keep Track Of Your Tumblers Effortlessly! - http://www.TumblerBuddy.app → UP Rock nerds Website: http://www.UPRockNerds.com → Amazon Influencer Shop: https://www.amazon.com/shop/influencer-55867868?ccs_id=0098309c-6801-4a8e-8102-5dc54a6b52d8. Like if this helped your rock tumbling journey! Subscribe and hit the bell for more rock tumbling tutorials, rock tumbler tips, lapidary content, and shiny rock reveals. Drop a comment with your first tumble results or what you want to see next! #rocktumbling #rocktumbling101 #tutorial #rocktumblingforbeginners #rocktumbler #RockTumblerTips #lapidary #rockhound #VibratoryTumbler #RotaryRockTumbler #LapidaryTutorial #rockpolishing
Simply put: This is my process for drilling a small hole in a gem or cabochon. The process is the same for any material except a diamond, which, lets be honest, you should not try to drill through unless you have a laser.... which I do not. Chapters: 00:00 Intro and tools 02:55 Starting to drill the stone 05:15 Speed up video of drilling 05:42 finishing the hole 06:28 Showing the finished results 07:38 Outro Tools you'll need: A diamond coated steel twist drill bit A flex shaft or similar handpiece/drill a shallow pan of water a stone or two to practice on patience This process takes anywhere from a minute to 10 or more, depending on a lot of factors such as a stones hardness, the depth you are drilling and how much pressure you feel comfortable applying. In this demo, I am drilling through turquoise, which is softer, but can be very prone to chipping or fracturing and so I am taking it very slow. Other materials such as quartz, agate, jade and jasper are all much harder and tougher and can take a lot more pressure but may still drill slower due to their inherent hardness. Other softer materials such as opal, amber, fluorite etc... will drill much faster. I use a slight up and down motion to help clear debris from the hole and also vary my speed to help the bit to bite into the stone. Experiment to find the speed that seems to cut the fastest.
A simple video showing two methods for testing turquoise at home. Both methods are non-destructive to natural turquoise. However, both methods will leave marks to fake turquoise. Supplies List: Q Tips are great for applying the acetone to the stones: https://amzn.to/3kLMT5B Acetone: Note that this IS different than fingernail polish, so using actual acetone will make a difference in the results. You can pick this up at most hardware stores, or online here: https://amzn.to/3DLdLul Nitrile Gloves Important: Nitrile WILL degrade with acetone, so while they offer protection for a few short tests, if you are going to be working with acetone for a prolonged period, then Butyl Rubber Gloves will be a much better choice. Please note that "black nitrile" is not Butyl. The Nitrile gloves I use in my shop can be found here: https://amzn.to/3cp1SOj Butyl Rubber gloves are more expensive, but are reusable and offer a better skin protection against harsher chemicals. They can be found here: https://amzn.to/3DCX6ck Kitchen Lighter: These are handy for lighting candles, or directly heating the needle to test the turquoise. Plus, I use them all the time in my shop for various purposes such as melting ends of paracord, etc... https://amzn.to/3DrJmRo Cheers, Austin Disclosure: I am a member of the Amazon Affiliates program and Earn a commission on any sales made through the links to the products I endorse. I make a great effort to only endorse products which I myself use and enjoy.
Hello my name is Cliff and I'm a gem cutter from Australia. In this video I take a fun approach to faceting gems. You will see me facet my own design called "The Zulu's Eye" in flame fusion Ruby. Jaw's also makes a guest appearance in this video and takes full control of filming, editing and sound at the "Vintage Time Studios". Please leave comments, like and subscribe. Thank you for watching.
💧Mineral Oil: https://amzn.to/3UMJtBY) 👉 Explore ALL my tools & gear: https://linktr.ee/cacklingchick Looking to get that shiny, polished look on your rocks without spending time or money on a rock tumbler? You’re in the right place! In this video, "Polish Rocks Without a Rock Tumbler: DIY Mineral Oil Method" I’ll show you how to polish rocks to a shine without a tumbler, using an affordable, easy-to-find product—mineral oil! This quick and simple method is perfect for rockhounds and hobbyists who want to add a little sparkle to their favorite stones without all the fuss. We’ll guide you through the entire process, step-by-step, so you can start shining up your rocks right away. Whether you’re a beginner rockhound or just love collecting stones, this video will help you get professional-looking results fast. Don’t miss the pros and cons section, where we break down what you need to know about using mineral oil for polishing. Supplies You’ll Need: ● Mineral oil ● Soft cloth, cotton balls or Q-Tips ● Mild soap and water (for cleaning) ● Additional soft cloth for buffing ● Rocks ROCK ON!! 😁👍🪨⛏️ 0:00 Introduction to method 0:10 Gathering supplies 0:56 Cleaning the rocks 1:10 Applying mineral oil 2:18 Enhancing tumbled rocks 2:50 Pros and cons of method 4:07 Comparing polish methods 4:46 Final review and conclusion #rocktumbling #rocktumblingforbeginners #rocktumbler #rockpolishing #tumbledstones #lapidary
An overview to cleaning quartz, with mechanical to chemical methods, highlighting a few examples.
I have consistently seen these three products recommended over and over as a way to clean quartz crystals, let's test them all side by side and see which one will yield the best results. Thanks for watching, and be sure to check out some of our other videos if you like this kind of content. #CurrentlyRockhounding #Crystals
This is how Gemstone dopping for a dop stick of the handpiece Faceter. Hope this would give an idea for the beginners to dopping with wax (Without glue or epoxy) and balancing the gemstone.
If you have been curious as to how the new iPhone 13 Pro macro photo and video mode works for gemstones then this video is for you. I look extensively at how it performs versus an iPhone 8 Plus for photo and video with a variety of stones in a variety of lighting conditions. #iphone13pro #gemphotography #iphone13promacro 🎵 Music by epidemicsound.com Stone Cookies - Dusty Decks 🎥 Gear Used: (Please note that these are affiliate links) Video: iPhone 13 Pro Nikon Z6 https://amzn.to/3fMQ4ab Nikon Z50 (x2) with 16-50mm lens https://amzn.to/3vsgoN9 Nikkor 105mm Macro https://amzn.to/3yKHBwW Nikkor Z 24mm https://amzn.to/3fncy2f Neewer Lights: https://amzn.to/34jcFWm Audio: Rode Video Mic Pro https://amzn.to/34jcIBw Rode NT-1 (x2 for ASMR) https://amzn.to/3urx9ab Boya Lavalier Mic (x 2) https://amzn.to/2Sx7DCS PreSonus Audiobox USB 96 https://amzn.to/3fqQsfC
Are you having trouble with your rock tumbler? Trying to figure out why your rocks aren't getting shiny? I have about a dozen years of experience helping people learn to tumble rocks and troubleshooting their problems. Let me help you figure out what you might be doing wrong. There might even be a tip or two in this list for more experienced tumblers. – MERCH – Buy Michigan Rocks shirts and other merchandise here. https://michigan-rocks-shop.fourthwall.com/ – HIGHLAND PARK LAPIDARY – Highland Park makes some high quality tools at reasonable prices. They also have the best price on grit that I have found. I make a commission if you buy something through this link. It doesn't cost you extra. https://hplapidary.com/?ref=ROBERTABRAM Use promo code MICHIGANROCKS for 10% off rough rocks and accessories. – KINGSLEY NORTH – Kingsley North is a lapidary store in Michigan's U.P. They make a great cab machine and sell many other brands too. They have a huge selection of rough rock, tumblers, grit, jewelry supplies etc. at good prices. If you buy using the following link, I make a small commission. https://fas.st/t/u7uaxb5V This is the cabbing machine I use: https://fas.st/t/vCjRymKC – THE ROCK SHED – I buy a lot of lapidary supplies and rough rock from The Rock Shed. I don't make money from your purchases there, but they have good prices and good service. This is where I buy my finer grits and polish. http://rockshed.com – AMAZON STOREFRONT – I also have an Amazon storefront. This is where you can find other products you may have seen in my videos. As an Amazon Influencer, I earn from qualifying purchases. It doesn't cost you extra. http://www.amazon.com/shop/michiganrocks – NANCY'S BOOKS – My wife is an author! Her novels are available on Apple, Amazon (Kindle or paperback), Barnes and Noble, and Kobo. We would be very thankful if you read them. Slinging Bullets: https://books2read.com/slingingbullets Trial by Bullet: https://books2read.com/trialbybullet Faded Spotlight: https://books2read.com/fadedspotlight
Im cutting a piece of amethyst in this video. The material is from brazil, im using a 25 year old ultra tec v2 faceting machine with a digital angle readout. Im an american hobbyist cutter. . Here are websites with free faceting designs. www.facetingdiagrams.org www.pinterest.com www.geologyproject.com Faceting machines i recommend; www.ultratec-facet.com www.facetron.com I use these faceting/lapidary dealers for supplies: www.lapidarymart.com www.lightninglap.com www.johnsonbrotherslapidary.com www.rockpeddler.com www.gearloose.com im a member of the United states faceters guild . https://usfacetersguild.org/
My name is Cliff and I'm a gem cutter from Australia. In this video watch me facet one of the world's most spectacular gems the "Cleopatra's Eye". The is a legendary gem design, and is well known within faceting circles. The gem is rarely seen faceted, as it is a difficult design to execute. I hope one day that all gem cutters get the chance to facet this wonderful gem. Best Wishes Cliff.




















