Simply put: This is my process for drilling a small hole in a gem or cabochon. The process is the same for any material except a diamond, which, lets be honest, you should not try to drill through unless you have a laser.... which I do not. Chapters:
00:00 Intro and tools 02:55 Starting to drill the stone 05:15 Speed up video of drilling 05:42 finishing the hole 06:28 Showing the finished results 07:38 Outro
Tools you'll need: A diamond coated steel twist drill bit A flex shaft or similar handpiece/drill a shallow pan of water a stone or two to practice on patience
This process takes anywhere from a minute to 10 or more, depending on a lot of factors such as a stones hardness, the depth you are drilling and how much pressure you feel comfortable applying.
In this demo, I am drilling through turquoise, which is softer, but can be very prone to chipping or fracturing and so I am taking it very slow.
Other materials such as quartz, agate, jade and jasper are all much harder and tougher and can take a lot more pressure but may still drill slower due to their inherent hardness. Other softer materials such as opal, amber, fluorite etc... will drill much faster.
I use a slight up and down motion to help clear debris from the hole and also vary my speed to help the bit to bite into the stone. Experiment to find the speed that seems to cut the fastest.
AI Generated·May contain errors
Video Summary
AI Generated
This tutorial demonstrates the proper technique for drilling clean holes in gemstones, specifically turquoise, for jewelry making. The author emphasizes the importance of using high-quality tools, maintaining low pressure, and drilling underwater to ensure a professional finish without damaging the stone.
Hey, today we're going to be drilling a hole in a gemstone.
So I'm making a pair of turquoise earrings.
Here I've already drilled a hole in this one, and this technique will allow you.
To get a hole.
It is nice and clean, both front and back, without any blowout.
So I've got my other stone here.
For this, you're going to need, of course, your stone.
Shallow container of water.
This one here has a kind of a rubbery bottom on it.
Keeps the stone from skidding around while you're doing it.
And you'll need a drill of some kind. I recommend using.
A flex shaft. This is a Fordham.
You can also use a Dremel if you like, as long as it has variable speed,
because you're going to want to go slow.
And I recommend not using a household drill or a construction drill.
Problem with that is they're too heavy and cumbersome,
and you lose a lot of the sensitivity and control.
That you have with a finer piece like with this, I can feel.
Feedback coming through the drill.
The last thing you're going to need is the drill bit itself.
There's a couple of different types, and let me show you what they are here.
Ever done any carving or looked for these on eBay? You've probably seen.
Something like this online. These are just cheap, coated diamond.
Burs here.
And these are used for gemstone carving.
They're not really meant for drilling holes.
So, what I have here.
Is an actual diamond, twist drill. So this is a.
Coated drill here, and.
This particular one is stainless steel.
And it's a high grade drill bit. I think this bit alone was like fifteen dollars.
So, uh, but it's worth the investment to get something.
That is of high quality.
The biggest problem you have with lower quality ones is that the diamond
layer either isn't very thick or isn't adhered to the metal very well.
And if it's not stuck on that metal,
which is usually from the electroplating, it will come off very quickly. So.
And if you ruin your stone, then well,
the fifteen dollars pays for itself by not breaking your stone.
Or drilling a terrible hole, so.
Let's go ahead and just do this real fast.
It's it's pretty simple, although can take a few minutes to do.
To start with, I've just placed a small mark on the stone here.
And so I'm going to put this down in the water, and it is completely submerged.
See if we can zoom in on that a little bit.
So, I'm just going to be applying very light pressure here.
The uh, you can probably see this is a the base of this has some flex to it.
So I know if I push too hard, it touches the table below.
And then I'm pushing too hard. So, anyways, just gonna push lightly.
Not too fast.
I'm just doing it nice and slow here. You can see.
Particles coming off here.
And kind of using some variable speed. I'm not doing very much pressure here.
Just letting the weight of my hand and the drill.
Push under the stand.
And this whole thing's underwater right now.
And the time it takes is going to depend a lot on the stone you're doing.
I drilled another piece of turquoise earlier.
And it was significantly softer than this one.
And I was able to drill through a half-inch thick chunk in about a minute.
This turquoise is a lot denser.
It's probably stabilized, but either way, it's a much better quality.
It's not nearly jockey.
And it's going to take a few minutes to get through this piece,
which is only about an eighth of an inch thick.
So what I'm listening for at some point, the sound of the drill will change.
And I'll know.
That I've gotten, the point of it through the backside, which hasn't happened yet.
So I'm gonna just gonna keep drilling.
I'm gonna speed up the video a little bit here,
so you don't have to spend 10 minutes watching me drill through this.
And then I'll slow back down again when I get to the point where I'm almost done.
Okay, so I just heard the sound of the drill change. Maybe you heard it too.
Pay very close attention. You can hear it starting to change sound.
More chatter sounds a bit rougher. You can see here. There's a tiny hole.
On the backside, so to prevent this from blowing out as I drill from the front side,
I'm going to flip it over.
Use that hole to center my drill.
And drill from this side.
Hingo, so here's those two uh stones with the holes drilled.
See a little tiny piece broke off, there, but that's gonna be hidden.
Uh, when I put the setting over the top of that.
Overall, it took probably about ten minutes to drill through a stone.
Uh, you might be able to go faster with different stones,
or slower with other stones.
But I wanted to take it nice and slow. I'm also going to briefly mention that the.
The reason why we use the water, there's submarines one.
Is to prevent the bit from overheating because if the bit overheats.
It's a lot more likely, to.
Lose its diamond coating. The second.
Is to keep the stone cool because if stones heat up, they're more likely to break,
and some stones can also have other problems when they heat up.
And the last reason is to protect your lungs because the water captures.
All of the dust and silicate particles that are coming off of the stone.
And you don't want to be breathing that in.
So hope you found that helpful. Just remember, key is.
Quality drill bit, water, and take your time.
Till next time. Thanks for watching.