These aircraft masquerade as enemy Shahed-136 drones during U.S. military war games

Military Aviation Technology
4 followers
3 Video Views·Feb 3, 2026
KestrelX flies both the KX-1 microjet and now the KX-2 propeller-driven aircraft to mimic enemy cruise missiles and long-range one-way attack drones. TWZ was the first media outlet to fly with them as they gave USAF 4th and 5th generation fighters a major drone threat problem to solve during the Sentry Savanna air warfare exercise. Here is a tour of KX-2
I'm Dan Holmes, I'm the Director of Operations at Kestrel-X,
and this is the KX-2, which is a modified Rizin 916
superveloce, so made by Porto Aviation and modified by us.
So we're just going to do a quick walk around
and talk about the airplane and why we use it for
UAS replication. So our objective at Kestrel-X is to provide
simulations of unmanned aerial vehicles, so things like the one-way track drones
that are being used in Ukraine and against Israel, as well as
against shipping lanes in the Med. So we use this airplane because we can
make it as small on radar as those drones that are attacking
Ukraine and also the shipping lanes in Israel, so the CAS-4 and the
Shahid-136. So this airplane has a Rotax 916, 160
horsepower engine in it. It's been modified to make it narrower,
so it's very aerodynamic as well as reduces
the radar cross-section. We've modified the canopy,
we've used radar absorbent materials on leading edges
out there, and then it also can carry payloads
such as things that simulate the uplink and downlink of a UAV
that's out there, as well as emitter pods, and we can carry pods on the
wings. We have hardpoints that we put on it as well as that.
So it's a full two-place cockpit. It's got a full Garmin
avionics suite in it, so it's capable of flying
in IFR or in the clouds in IMC conditions
via GPS. We primarily navigate via GPS.
We comply with all FAA airworthiness requirements. This aircraft is certified
experimental exhibition and we fly it to demonstrate those low
observable properties in it. Just doing a quick walk around, here's
the cockpit with the two-place thing with
luggage in back. The wings, the entire airplane is a
monocoque carbon fiber structure to that. We have two different
configurations of our airplanes. Some carry 46 gallons, some carry 52
gallons of fuel in the wings through both a
main tank and a tip tank to do that.
We have our materials out here. You can see the antennas on the top
and the bottom. We use those. We have both UHF and VHF radio capability
as well as that is where the antennas we use to do our
UAS emission simulations. If we look under here along the wing
of the other airplane, out there you'll see a bracket hanging
down. That is a hardpoint mount for carrying a pod.
So this airplane just doesn't have it here right now.
Retractable landing gear. It's important that we make the airplane as skinny as
possible. This landing gear is very well sealed to the
fuselage and makes the airplane very fast.
We can go as fast as 240 knots but typically UAVs don't fly that fast
so we will fly as slow as the UAV flies down to about 60 knots.
GPS antenna on the top. Why VTAIL? Well, fewer flight control surfaces. The
airplane is slicker and faster. It also is less observable to radar when
you don't have as many forward-facing surfaces. So
that's why we use a VTAIL configuration and you'll see all the
RISNs have the same configuration. So the airplane was
the best we could find for doing this job.
Coming around the flaps out there. Fowler flaps.
So they actually have four positions that allow us to get to a very slow air
speed. The airplane basically stalls below 40
knots and can fly as fast as 240 true which is kind of what we already
discussed. And then the left side looks a lot like the right side.
So bringing us back up to to the cockpit
with the center stick. This particular airplane has a
automatically controlled propeller out there. Other ones have a manually
controlled propeller. And then Rotax is a fuel injected engine
so we don't need a mixture control for that.
