The Basket Weave Cutting Board

D.E. Jaeger Woodworking
97 followers
17 Video Views·Jul 23, 2025
This pair of basketweave style cutting boards is created from exotic padauk and purpleheart and domestic walnut and maple.
Backing Tracks...
"Stinson" by Reed Mathis
"Communicator" by Reed Mathis
Hello and welcome back to Deager
Woodworking. Today we take these four
different types of hardwood stock from
this to this. A deep rich colored
cutting board with a weave type pattern
that is sure to attract some attention
from your guests. So, let's head back
into the shop and see how to create this
beautiful board.
Down
here
[Music]
down.
[Music]
I'm starting this board with 24 pieces
of stock, six each of Paduk, purple
heart, hard maple, and walnut. Each
piece is 16 in long by 2 in wide by 3/4
of an inch thick. But I'm going to cut
each of these pieces lengthwise in half.
They're really too thin to safely cut on
the table saw. So, we head over to the
band saw.
I set my bandsaw fence so that when
passing each piece of stock through the
blade, I'll get roughly two equal width
pieces. Here's a view of one of each of
the pieces, but I'll do this for all 24
pieces of stock.
[Music]
[Music]
[Music]
[Music]
Now that I've passed all wood through
the band saw, I have a total of 48
pieces somewhat equal in length, width,
and thickness. However, right now I have
essentially a smooth side and rough side
to each of these pieces. This is the
first process to undertake in refining
each piece so that it is more uniform in
thickness. I'll do this with the drum
sander.
I run each piece of stock with the rough
side up and the smooth side against the
belt. This will remove the small grooves
caused by the flexing of the bandsaw
blade as they were passed through.
The other thing I'm trying to achieve
when sanding the thickness of each piece
is to get each piece to a nominal
thickness of a little less than a/4 of
an inch. You'll see where that comes
into play when I begin assembling the
pieces together.
[Music]
[Music]
[Music]
Now that all pieces have been sanded to
thickness, you can see from this graphic
how I plan to assemble each piece.
Starting at the bottom, I'll take a
piece of maple, then a piece of purple
heart, a piece of paduk, and then a
piece of walnut, and repeat that until I
have doubled that layering pattern.
[Music]
[Music]
Now it's time to glue up this layered
pattern with eight total pieces in each
assembly, two of each type of wood.
[Music]
[Music]
[Music]
I'm using some parchment paper between
each assembly so that I only have to
perform Perform one glue up.
[Music]
[Music]
[Music]
[Music]
[Music]
[Music]
[Music]
With a few extra clamps in place, I'll
leave this to dry overnight. Although,
I'll come back in about an hour to
remove some of the partially dried glue
that was squeezed out during the
clamping process.
[Music]
After an overnight drying time, I
unclamp the assemblies and get them
ready to send through the drum sander.
[Music]
One side of each assembly has more
residual glue, so I'll make sure to
place them face up through the sander.
Once I'm happy with the trressess of the
surface, I'll send the opposite side of
each piece face up through the sander.
I'll do this until I have four equal
length sides
with each assembly. Now at a squareness
of a little less than 2 in on each side,
I'm going to alternate each piece in
this next glue up. This will begin to
establish the pattern of the cutting
board.
[Music]
[Music]
As I finalize this glue up, I really
want to make sure to remove as much glue
squeeze out as possible so that it
doesn't harden. and create an uneven
surface. I don't want to remove any more
material than necessary when sending
this through the drum sander tomorrow or
I'll risk losing the pattern.
[Music]
As I begin to send the assembly through
the drum sander, I'll take very shallow
passes. I only want to remove the dried
glue and as little of the wood surface
as possible.
[Music]
Once one side is done, I'll flip it over
and remove any glue on the opposite
side. Again, making as shallow passes as
possible.
[Music]
It's now time to section this board into
equal width pieces. For this, I'll use
my table saw sled.
After squaring up one edge, I'll set the
width marker of 1 and 1/4 in and begin
crosscutting the assembly to get as many
pieces as it will yield.
[Music]
[Music]
When I get close to the end, I'll switch
back to my saw fence and make the final
cut. It's safer and much more accurate.
I never want to make a cut that I don't
feel safe making.
[Music]
It's now time to reveal the pattern for
this cutting board. First, I'll lay each
piece down flat, and then I'll take
every other piece and turn it 180°.
After pondering the number of pieces and
size, I think I'll make a smaller
matching board to go with the larger
one.
[Music]
We've reached the final glue up stage,
and I'll need to take special care when
aligning each piece to retain the
pattern. I'll lay down a piece of MDF
with a piece of parchment paper to
prevent the glue up from sticking.
[Music]
[Music]
[Music]
[Music]
[Music]
After I've check the alignment across
the board, I'll slowly begin to apply
clamping pressure.
[Music]
And as before, it's necessary to remove
any glue squeeze out to reduce the
amount of sanding required.
[Music]
Lastly, I'll need to apply some downward
force to prevent any vertical shifting
when the clamping pressure is applied.
[Music]
It's good to see that I finally found a
use for those weights.
[Music]
Oh yeah, don't forget about the smaller
board. We've got to perform a glue up on
it as well.
[Music]
One last trip through the drum sander to
true the surfaces of these boards and
then it's on to hand sanding.
[Music]
For this board, I decided to add a 45°
chamfer on all edges so that the board
was easier to grip when laying flat on a
table.
[Music]
I can see now that some sharpening or
replacement router bits are in order.
[Music]
It's time for sanding. For most cutting
boards, my process is to use 120, 180,
240, and 320 grit sandpapers.
Before each grit, I like to scribble
lines across the board so that I can
easily determine that I've covered the
entire surface of the board during the
sanding process.
Bring
[Music]
it down.
[Music]
I need to make sure that I hit those
chamfers with the sander as well.
[Music]
[Music]
After the entire board has been sanded
with one grit, the process is pretty
much a rinse and repeat with each
subsequent grit.
Before beginning the sanding process
with the 320 grit paper, I like to raise
the grain of the wood by lightly
spraying all sides with water.
[Music]
[Music]
[Music]
When the water has completely dried, I
proceed with the final 320 grit sanding.
Hey,
[Music]
[Music]
[Music]
Before proceeding to the treatment
phase, I'll run both boards through my
laser. to engrave my traditional
finishing logo.
[Music]
It's into the bath we go. Food safe
mineral oil bath, that is. I'll let both
boards get a good 15minute soak and then
place them on the drip dry rack
overnight.
[Music]
[Music]
It's the final day for these cutting
boards. I'll apply a foods safe cutting
board conditioner to all sides of both
boards and then wipe them down with a
clean paper towel.
[Music]
[Music]
[Music]
Hey,
[Music]
hey, hey.
[Music]
[Music]
I have to say I am amazed at the depth
of color that the different wood types
produced. The Paduk is a deep red rather
than the orange color it boasts and the
purple heart has a deep blue hue. Along
with the richness of the walnut and the
contrast of the maple, this board turned
out very impressive. And I'm really
happy with the large and smaller
accompanying board arrangement.
[Music]
I really hope you enjoyed this video as
much as I did making it. If you did,
please give this video a like. If you
have questions, please leave me a
comment below. I will try to answer all
comments as soon as possible. Feel free
to subscribe and turn on notifications
as I have some future videos in the
works. As always, thanks for watching.
[Music]
