Pole barn house wall with window header! House build #12

The Kelley's Country Life
18 followers
Welcome back everybody my name is Andrew and I'm Tiffany and we are the Kellys and you're watching
the Kellys Country Life. So today as you can see we're set up back in front of the pole barn house
and this is going to be episode two for framing. So I explained in the last video that I was going
to keep it short and not go over many details. When I got to editing that video it was over 30
minutes long by the time I got done with it and I still had stuff that I cut out that I wanted to
So I asked at the end of that video if you made it that far and I'm asking now what kind of videos
would y'all like to see moving forward? Do you just want me to jump straight into building or
do you like for me to go over the details? A lot of people have requested that but I'm always open
ears and willing to listen to what y'all would like to watch. Sadly if I'm going to go over a
lot of details and plans and things as I go along that eats up a lot of time and these videos will
get longer. So again I would love to hear if you like the longer videos more details involved or
just want me to jump straight into building as we move forward with this house. There is a lot to
cover over the next many many months here so I would like to make the content that y'all want
to watch. So speaking of that being that I haven't heard from you just yet we're going to go over
some detailed stuff today because I promised that in the last video. I'm going to show y'all some
things in the plans, how I went out and purchased some things I need, how I read some of the stuff
in the plans because again a lot of y'all have reached out to me and you are building pole barn
houses or getting very close to so maybe some of this stuff will be helpful to you. So let's get
started. All right it is extremely bright and I'm about to show you white paper so hopefully the
camera picks this up and doesn't blind you. Where do we begin? Not on that one. Yeah this is the one
I want to show y'all right here. This is our set of house plans. All right so if y'all watched the
last episode where I raised this wall right here I explained at the beginning of it I had the hardest
time in the world finding some of the most basic things that the plans required to build this house.
So I'm going to go over some of that right now. Okay so here is our set of plans. It's kind of
just a basic layout of how we want the wall set up. I'm not going to go through every bit of this
but I'm going to show you some of the things I read and why I purchased some of the things that I did.
So for example if you look at the base plate of the house of all the walls it's requiring what
are half inch titan bolts and it says at the corners and 36 inches on center. So every 36 inches
it wants a titan bolt and as you've seen in the last episode we put some of those down.
So this is a titan anchor. These are designed to go down and bite into the concrete. They're very
highly rated, work very well. They also require a base plate washer or commonly just called a
plate washer to spread that load out once it goes through that base plate. That way the washer
or the bolt itself the bolt head can't pull through that wood should there ever be such
crazy uplift. So that's some of the stuff that I had to go try to find. You see it gives the layouts
of the studs 16 inches on center. We covered that in the last episode on how we built the wall.
Some other stuff that I kind of had to go after to try to find as far as OSB that it calls for,
the nails, how you nail it etc. Also on the nails as you can see in some spots it calls for 8D
nails. I believe that's a two and a half inch nail if I remember correctly. Quite common
for sheathing. We'll get into those a little bit later and then you'll see in some of the other
ones it calls for 16D nails which is you can see them in the three and a quarter or three and a
half inch nail but most common is a 16 penny nail is a three and a half inch nail and that's for
some of the plates that we have to tie together. Also what I struggled with was all window and
door headers to jack studs. We're going to build one of those today. I'm going to show you require
these straps right here. So this is a light duty that's what the L stands for strap. So LSTA21
means 21 inches. That is this type of strap right here however I could not find those.
This is a M so MSTA medium duty and it's 24 inches. So this is much heavier duty than what
the plans call for because I could not find these straps anywhere. I had to wind up paying about
twice the money for the longer thicker strap but it is what it is at this point. Also I talked about
in the last episode how we had in the plans that we want to lag the walls or the two by six studs
into the six by six post. It says use three inch lags 24 inch on center. I went with a little bit
bigger lag it doesn't hurt didn't cost much more money and that's what we wind up putting that two
by six over there into the six by six with. I always want to throw a washer on that as well.
So that was some of the basic stuff the nails the bolts the plate washers and straps that's what I
need to kind of carry along here. As we start getting into sheathing and other things I'll
come back to the plans and show y'all some of the stuff that's required here. But this it was an
absolute struggle just to find some of these most basic things right here and the hardest thing to
find was the framing nails for the nail gun. Now we just built this wall right here. It was the
easiest one to start with right there no headers no nothing. So today we will be building a header
we're doing some strapping and I'll show you how we'll put that together. So we'll have to read the
measurements off the plan to get exact dead center of that window. So as you can see we have 11 foot
eight inches to this wall right here plus another five foot eight. We'll add those two together to
get dead center of that window right there. All right so here's where things get a little
interesting. If you watch the last episode we can't just strictly lay timbers out 16 inches
on center because we have six by six post constantly breaking the wall up throwing us
off. We're not just making a long run of wall to where we can just 16 inch on center lay everything
out and raise it up. Plus we've got to make sure I decided we've got to make sure the sheathing
lines up and butts up on a stud because I do not want to have to rip down a whole bunch of sheathing.
So we've got to go do some measuring on the last wall before we can lay this wall out. All right so
if you watched the last episode I stated that I really want to start my sheathing on the outside
edge of the six by six post for a couple of reasons but the most critical is I want the sheathing to
act as a hurricane strap to the wall as well. It's already bolted nailed in but I want to make it
all one piece as much as I can. Sheathing will help do that that way if these posts ever do
rot or give me a problem they're supported greatly by the interior walls as well as the
sheathing locking everything together. So if I start the sheathing out here but I start this
wall 16 inch on center it's not going to match up. I have to do 16 inch on center from the outside edge
of this post right here so whenever that four foot sheathing stops it stops on this stud right here.
When the next four foot sheathing stops it's on this stud right here and I can continue to go.
Now that I'm about to build another wall down here I need that sheathing to stop on this same
stud at the end of the other piece of sheathing and continue so I have to figure out where four
foot from the center of this stud will be to the center of a stud down here. Hopefully that makes
sense. I'm trying to avoid ripping a bunch of sheathing and sadly I can't build one long wall
and perfectly line everything up and raise it. This is one of the aggravating parts about a
barn house build and I have to do some odd measuring for these exterior walls.
All right so I know my sheathing is going to stop on this stud because I marked that
whenever I built this wall in that last episode. So I'm going to hook on the outside edge of this
and try to grab some quick measurements. All right so I just made a mark on the concrete
at 48 and three quarters inches because I want to find the center of that stud since I hooked
on the outside edge and they're one and a half inches thick. Now I can come to the inside of
this stud to that mark and I know I need a stud at 18 and a half inches on that other piece over
there. So we know we'll have a stud right here at the end. Always will. I'll come to my 18 and a
half inch mark and I'll make sure that I have one right there ready to nail that sheathing into.
Planning this ahead now is going to save me a lot of headache later when it comes time to put that
sheathing up and go. All right so where that 18 and a half inch mark was I made I went 16 inch on
center from that mark all the way on down. That way I know I can continue to carry my four foot
wide sheathing and always hit on that mark. Now you still have to comply with 16 inch on center code
so if there's anywhere in between like right beside this 18 and a half inch that I need a stud
I'm gonna have to double two up right here. Looks like this wall is only going to require one extra
piece of lumber which is perfectly fine. I bought extra to do that. It'll make the wall stronger,
comply with code, but I'm still putting the studs where I need them and I have to do all
that ripping down of the sheathing. All right just like in the last video it's at this point
that I'll take my big framing square put on those lines and go ahead and transfer the lines to my
top plate. That way whenever I have bottom and top plate and go to nail my stud in I know I'm putting
them perfectly square with each other. Now if we didn't have to put a window or door in this wall
right here we go ahead and start cutting our studs putting them in there raising the wall just like
we did that last one but while this bottom plate is down here and top plate we have to go ahead
and set up where our window jack studs cripples and a few other pieces have to go plus we still
have to build our window header. Now according to the plans the window dead center was at 16 feet
four inches so I just measured that entire wall post included and then I'm going to add that length
plus what I need on this particular bottom plate to find all the way from this end down there to
16 feet four inches so we can start laying our window out. So before you cut your window opening
this is the best time to either already have your windows or know the rough opening size.
I did go to Lowe's where I'm most likely going to buy my windows and took some pictures the other
day of several different types of windows including the tag on the side that called for the rough
opening. Now it's quite common that I'm reading the rough opening you can add a half inch to either
side to that so up to an inch so to give you a little bit of wiggle room and kind of level the
window out in there we are going to add a little extra there because the windows do have a big
enough lip around the outside that you can still nail them in with the rough opening big and a
little bigger than what's called for. So it just so happens the windows that I looked up calls for a
36 by 48 rough opening so really we can make that 37 by 49 37 wide 49 tall and now we have to lay
that out on our bottom plate. So I have found the dead center of the window right my measurements
down here for the opening that we want so this is dead center again the plans called for this
to be 16 feet four inches dead center of the window from the furthest corner of the wall.
I measured all the way down found that mark all right now we're going to take the 37 wide opening
that I'm looking for split it in half so that would be 18 and a half inches. I know that I can
go that wide down here and make a mark down here because on the outsides of these marks we are
going to actually have to put some support studs. I made a mark all the way from here over to here
everything in between would technically be the cutout opening for our window this will make more
sense in a minute whenever I put everything up. I know on the inside edge of that we're going to
support a window header and it's done with what's called a jack stud so we will have a jack stud on
this side supporting that header for the opening as well as over here there's different marks in
the industry for this but I just write a J it's very simple. Now on the other side of that we
will have to do what's called a king stud so I'll put a K for over there and make my marks as well.
You always have to have an outside stud supporting a jack stud so king stud jack stud then everything
in between because we're now we're going to have a cutout and window seal these are going to be
called cripples they're short studs that are going to support the window seal. Also while we have the
bottom plate down I have to go ahead and drill out my holes for the base plate bolts now's the time
to do that so you don't drill through this later with a wood borne bit hit concrete and damage your
bit and the plans call for these to be 36 inches on center. All right now it's time to go carry my
top and bottom plate inside and set them down and it's critical that I take them off of the
saw horses and put them in there the same way they're laid out right now since I have such
odd measurements and we're not just raising a full interior wall.
All right so now it's time to make the window header this is what's actually going to support
the wall above it since we're taking out an open section of studs here so headers are critical
especially on load bearing walls. So on a two by four wall you would normally do two two by material
inch and a half inch and a half and sandwich a piece of half inch ply or OSB in between to get
three and a half inches. On a two by six it's actually five and a half inches so you'll take
three pieces of two by material in this case two by sixes and you actually have to sandwich some
half inch material between both of them because as you can see if this was the wall stud right there
we still have a huge gap to fill about a one inch gap so two half inch pieces apply in between
this lumber will get us the spacing and header size that we need to sit on one of these two
by six studs. Now I don't know the national code it's for you to look up but I know in my area if
you have a span over four feet eleven inches you have to go up to two by eight material anything
smaller than that you can use two by six for a header material and we will have some windows
in the house that will go up all up to two by ten headers for the big window openings
down on the balloon frame wall at the other end it'll be quite a while before we get to that
but you'll see anywhere from four feet nine to four feet eleven inches anything wider than that
step up in size to two by eight material for your header. So I've got my three pieces cut at 40 inches
that I need for my header now I have to cut two pieces of this half inch ply to go in between
them the same exact size. All right now it's time to assemble our header I don't even know if wood
glue is required but since we're already over building this why not. All right so these two
studs that I just call are cut right here called the header jacks basically kind of jack and hold
up the header. I cut these at 81 inches because I want them to match up on the top of the windows
to match up the tops of the doors that way I can keep it consistent throughout the house
that's kind of industry standard to do that so it catches your eyes the top of all the windows
uh top of the header jack should be about 81 inches cut these boards plus an inch and a half
a bottom plate down there puts it about 82 and a half inches. Also while I was in Lowe's I took
pictures of interior doors exterior doors and took pictures of the side sticker that called for the
rough cut opening all those were around 82 to 82 and a half inches so I am trying to match my window
openings tops of the windows with the doors it'll just look better to the eye as you look across the
room. So there is our door header installed we've got our jacks we'll go ahead and start getting
everything nailed in and then we'll have to put some more pieces up top that are called cripples
top and bottom plus our window seal. All right now that we have removed the wall stud supports here
that's what we built the header for but we have got to put these small pieces called cripples in
here to support this top plate from this header if we were to put weight up here right now with
nothing in between it causes header to sag so all we're doing is just reinforcing. Now if I were
thinking I wouldn't put this top plate on until I nailed down into these so now I'm about to kind
of toe nail everything. So now I have cut my cripples that are going to support the window seal
and then there is our window seal. Now it's a good thing Tiffany was out here with me today
because we changed our mind on the window size in the plans we just stuck in long 30 by 50 inch
rough opening windows and we got to thinking in a bedroom we don't really want a long window like
that those are more for living rooms but the other reason we don't want a long window that would have
came down to here is if we decide to ever move the bed over to this window and have a big headboard
or this side of the room excuse me that window would be in the way. We're also going to put a
unit in this I know I know what you're thinking a windy unit in a new house trust me we don't care
anymore when we finally put one in on our last house and you can run the bedroom at 60 something
degrees but still leave the rest of the house up at 80 there's no point in cooling down the rest of
the house when you're sleeping in the bedroom all night we like to make that much colder and it
saved huge on our electricity bill plus not to mention anytime we have to run the generator and
we're you know out without power for days say a hurricane or something those generators can run a
windy unit but the ones that we have won't run a big central ac so we can sleep at night with ac
it's extremely important to us to have that so that got us thinking we had a big window down
to here like was in plan and had a windy unit in it and we ever put the bed over toward that side
it would completely block it so we decided to go with a 36 by 36 window which is very common size
right here so i did my opening 37 by 37 to give me some leeway so we did change that and i think
for good reason all right so the last thing to put in is these windowsill they're called cripples
so we'll put these in they still keep us going with that 16 inch on center which is critical
because one of these is going to be where my sheathing stops and i need to butt to it
all right moment of truth we're going to try to raise this heavy thing and hopefully it fits
yeah you know i have to do that by myself
after a little bit of trimming got it to fit i am definitely guilty of making things too tight
there's about an eighth inch too much on the top all right so tiffany wants to try her hand
at the old dewalt impact keep going till that washer pulls in the wood a little more
all right now you ain't doing good for the camera you're blocking everything we can't see what you're
doing all right so if the bedroom wall ever blows in it's your fault
all right so tiffany's trying the old hammer drill all right now keep running it and pull it up
all the way out so it'll clear itself yeah easy it's got power
now go all the way back down one more time okay all right that should do it
well the last thing left to do according to plans before we can call this wall
officially framed is it says to tie these headers with these straps to the jack studs
so all i can figure i'm going to do is everywhere there's a nail hole
strap this header to this stud i don't know what the heck i'm doing i forgot i bought this thing
thanks to one of y'all recommending it it's going to be a lifesaver for these straps
and these gigantic 16 penny nails all right to those of y'all that do have experience in
construction i'm seeing some conflicting stuff online here my plan specifically states to tie
all door and window headers to the jack studs with a strap it doesn't say anything about top
plate or any other stuff jack stud and headers all it says so i'm seeing online people saying
no the headers got to go all the way to the top plates it's got to go all over the place
it's too late to call my inspector it's the weekend so i'm curious to see what y'all have
to say about that because according to the plans this is exactly right so let me know what you uh
what you think i also read online from a lot of forums that you'll put the straps on the interior
not the exterior so i'm gonna wait to do the exterior until i hear from some of y'all
all right well here we are enjoying our bedroom window view so beautiful right
yeah it is what it is all right well hopefully y'all enjoyed it uh yes it's another one wall
day i'm glad she was here to see that it ain't just as quick as it looks on tv took quite a
to build out all this header and get everything figured out but it was just like the other wall
now i know measurements have a good general idea of the flow of things and it should go quicker
and quicker as we move on down we've only got one more normal size wall the eight footers here
before we have to go into a half wall half eight foot to twelve and we start going out into the uh
you know full 12 foot height for the living room so that's going to be a little interesting
that will be coming up thank y'all so much for watching hopefully enjoyed us trying to figure
out how to build our house we'll take all constructive criticism if you've got some
negative comments they will get deleted but constructive criticism we will gladly take
we are not home builders we're doing our best to read the plans codes and try to figure this
thing out and we would love any help or information that y'all may give us you know you want to say
well let's just keep plugging along yeah let's keep plugging along as in getting my dad gum
house done is what she's trying to say all right well thank y'all for watching we'll catch you on
the next video
