Origami Rabbit -Inflatable (Robert Neale)
Sep 19, 2023
In this video we're going to make an inflatable rabbit.
Visit our website OrigamiSpirit.com
to see our related blog posts
and for more creative ideas on how to use origami.
This is Leyla Torres of OrigamiSpirit.com
This is 6 x 6 inch paper, 15 x 15 cm.
If we want the rabbit to be white,
we begin with the white side facing up.
If we want the color, we begin with the color side facing up.
We fold in half side to side, bringing the edges together.
Book fold, open and repeat.
Unfold, turn it over.
We are going to create folds from the center to the center
on two adjacent sides.
We are going to rotate slightly
and we are going to create a fold horizontal
from the folded edge to the corner.
We can bring this flap down.
Match here and this corner is folded in half.
Unfold and now we create a valley fold vertically.
Bring this edge to this corner.
This match and the point is divided in half.
We're going to rotate it slightly so that it looks like a house
and place our fingers behind, bring it forward and collapse.
On this side we have a preliminary base that is double
and on this side we have a waterbomb base.
With this section we are going to do a petal fold.
We create a fold from the lower corner center
to the folded edge here and here.
We bring this edge to the vertical center.
Unfold and we are going to make another fold
from this point to this point where the creases meet the edge.
It's a horizontal valley fold.
Unfold.
Now we're going to place our fingers underneath.
This is going to be like a hinge.
We press up and we're going to reverse two folds that we have there.
We have this as valley fold and valley fold will become mountain folds.
We can press from the side.
The folds that we have underneath are already in the right direction.
Valley folds.
Inside the upper flap we reverse those from mountain to valley.
Patiently we just help the paper to reverse that fold.
Outside here it should be now a mountain fold.
Making a nice sharp point.
Now we're going to slightly open this center area here
to pull out some paper from inside.
Open a little bit and then identify a layer there.
A single layer.
We are going to bring it out.
Whatever is a mountain fold here is going to turn into a valley fold.
We're going to repeat here.
Identify the little flap there.
Softly bring it out.
Turn this into a valley fold.
We are going to fold along the center, corner to corner.
This is a valley fold.
We are hiding the color.
We have a folded edge here.
We are going to make a valley fold right along that edge.
Same here.
We make a diagonal fold here, about there,
by bringing this flap down, starting at the corner.
The guideline is that this line will be parallel to the center.
Press.
Same here.
These will be tabs.
We are going to look for a pocket inside here.
We are going to bring this in.
Tuck it in.
Repeat here.
This is what we have.
Turn it over.
We are going to make a valley fold from this corner down to the raw edge,
aligning the folded edge with the vertical crease.
Repeat here.
We will make a fold from this corner up to this edge.
The guideline is that when we bring the flap up,
it's at a 90 degree angle here.
This edge is parallel to what we see underneath.
Repeat here.
We locate the center at the bottom here
and create a valley fold from that center to that corner
and from that center to this corner.
Valley fold.
These are the ears.
We are going to bring that layer of the ears,
the right layer to the left,
and the left layer to the right.
There is a little hole right there at the point.
We are going to blow on it.
Actually, we can hold from one side and the other as we blow
so that these don't come apart.

