Must See Ceramic Trimming Hack!! Attach a Coil to Create a Foot.
5 Video Views·Jun 10, 2025
Welcome back! We are going to go ahead and get a foot on this and we're not going to trim it.
We're actually going to attach it while it is in the trimming dryness or trimming consistency.
So this is the platter that we threw or bowl plate, however you want to call it, in the previous video
and so now this is ready to trim and we're going to go ahead and show a different method on how
to get a foot on this. So a few things that you guys will need. You need a needle,
your favorite trimming tools, your wads of course, a brush, and then you'll need a container of water
or slip. So I got my throw water that I've been kind of holding on to and we're going to go ahead
and center this like we are going to trim it normally. So let's go ahead and get that going
first. And so this has already popped off from another board so we're going to go ahead and flip
it over and then center like we normally do if we were going to trim it without attaching.
So tap centering. There we go. I got my wad to secure. So I don't need too much because this
is a fairly flat and wide piece. So if you wanted to use more clay to anchor,
that's up to you. Or if you have a trimming device such as a griffin grip,
that works too. So let's get this secure. So whenever you get it secure, always put your
free hand on top of the piece so it doesn't move. And then your opposite hand will be applying
downwards pressure to get it stuck. And I like four. You could do three if you want or you could
do more. Okay. Last thing is gently push the wads into the piece. Not too hard because I don't want
to dent it. And give it the wiggle test. All right. So this is good to go. And we're going to go ahead
and trim this like we normally do to start it off. So the first thing is getting rid of the
overhanging clay. Taking the trimming tool, holding it so it's perpendicular to the ground,
and then just trimming this edge to reveal a straight wall. My clay is a little dry so I'm
going to add a little water as I trim. And I'm going to get rid of a little bit of these bumps
that are on the outside. And the downside of adding water is it does get sticky so the clay
kind of sticks to itself. So right here you can see bits got stuck so it's got to clean that off.
And then from here, because I'm going to attach a foot with a coil, I need to decide where the
foot's going to go. So I want to bring this in just a tad bit so I have a little more of a rounded base.
So I'm going to trim a little more over here and I'm going to prep the bottom so that I can go
ahead and start trimming and getting the foot ready. So I'm basically revealing where I want
my foot to go. And then I can always trim more away later, but this is just the general setup.
So you basically want to remove all the unwanted clay from the outside first.
Okay, so right there looks pretty good. Now I'm going to go ahead, get a coil ready, roll it, and
then we're going to go ahead and place it on here and then line it up. So let's go ahead and roll
that coil. I always like rolling on a hard, non-porous surface. If you have a canvas table
and you're rolling that, the clay tends to dry out a little faster. So we're going to go ahead and prep
our clay. This was a little more than a pound of clay when I started kneading it and it's always
recommended to knead your clay before you transform it into anything useful to get the clay more even
in consistency. A half a pound is pretty hard to knead and you can kind of see my hands are a little
too big for it, but I do recommend kneading it first. And so I already did it on a larger piece
and I cut it in half and this is the other half. And so once you have your clay ready, we're going to
start transforming it into the coil. Now we don't want any flat ends or concave ends, so we're going
to want to tap that away. And then to get this prepped into the coil, I'm going to go ahead and
start squeezing it into a log. Now when you do this, if you have flat ends, you're going to notice that
it's going to start caving in on you. So make sure that you tap those edges away to make it pointy
like a pencil or a tip of a carrot. The same thing on the other side. And very similar to when we throw,
if the tip of your coil is flat or caving in, when you roll it, the sides will always expand
faster than the middle, causing this to divot. So you always want your ends of your coil to be
pointy like a carrot so that you don't create those divots. Okay, so now it's kind of looking like a
sweet potato. And then we're going to go ahead and then start thinning out this middle section.
So I just put on my hand, and I just squeeze and rotate. So I'm prepping it into the coil shape.
And one thing when you work with coils, you want to make sure your clay is relatively soft.
If it's too dry and you roll the coil, it's going to crack on you. So just one thing to keep in mind.
Now I want a nice round coil for the foot. So in order to fix this, I'm going to go ahead and take
the coil, tilt it, and roll it so it's taller than it is wide. Push down on the tall side so that the
width is the same height as the top. And then you go ahead and you twist it like a churro. When you
twist, you got to make sure you don't twist it too hard, or you're going to end up ripping the center
section, especially if it's drier. And then when we roll, again, light pressure and focusing the pressure
in the center, because that's where I want to thin out, because my ends are already getting a little
on the thinner side. So I don't want to get that too thin. Now as you roll, same thing. If you start
noticing it's flattening out on you, push down on that tall side, gently twist, and repeat.
And keep rolling until you get this to the thickness that you want, and the length that you
want. So ideally you want a nice even thickness, and you want it nice and round all the way through.
So once again, my end is starting to get flat, so I'm going to focus just on that side to push to
square it up, and twist, and then continue rolling. Now just remember, as soon as you start getting a
flat side, you have to fix it, or it's just going to transfer all the way through your entire piece.
All right, and then you just keep rolling, and I'm going back and forth, really focusing on the
thickness, to make sure that this coil will be perfect for my foot that I add to the bottom of
the platter. All right, last thing is the bend test. You want to make sure that this can bend
without cracking. So you take your coil, and you start forming it into the general shape that it
needs to be, and if it doesn't crack, then you're golden. If it starts to crack just a tad bit,
it's a little too dry, and if that's the case, you want to rehydrate your piece with wet newspaper.
So I'm going to go ahead and get some wet newspaper, and show you the easiest way to hydrate
this piece. So I had a sheet of newspaper, I crumpled it up, dunked it in a container of water,
and squeezed all the water on, so I don't want it dripping wet. And then I'm going to open it up,
push this to the side, and open it up gently, because I don't want this to rip.
And then you basically take your coil, put it on one side, and just like you're making a sushi,
you're just going to go ahead and roll it up. At this point you could spray a little bit of water,
and then roll. And then you can either slip this into a bag, cover it up for about five minutes,
or put a bag over it. But basically you want to keep this airtight, and then let it sit for about
five minutes, and then unwrap it after those five minutes. And the coil should be wetter and
more hydrated, that you can go ahead and bend it without cracking. If it still cracks, smooth that
crack out again, put it back, and repeat for another five minutes. Now that is the reason why
you want a coil or a piece of clay that's a little on the wetter side, because if you roll a dry one,
it's going to crack on you, and it takes more time for it to hydrate. So that's a little tidbit for
hydration for any of you hand builders that also wheel throw, and we'll probably make some more
hand building videos in the near future. So this is actually good to go, so I'm going to take this
to my pottery wheel, and go ahead and get started with the attachment. So I got my coiled rolled,
and it's a little bigger than what it needs to be. So I'm going to go ahead and position it so that
the most consistent size, which is this middle section, is where I'm going to use. So I'm just
going to place it, and it's okay if your coil is not 100% even, because it is hard to get it there,
but you just want to try your best to get as much of it as possible. So right there I'm going to use,
so that looks pretty good, and I'm going to line it up basically exactly on this edge
that I trimmed away. Okay, I don't want any of this, so I'm just going to rip that off,
and then I'm going to place this on top of itself. So from here, once I line everything up, I'm ready
to cut through this to remove the excess. So I don't recommend you cut straight down, I recommend
you cut at a 45 degree angle, or slightly more than that. Now you can use your needle to cut,
but I always use the analogy, using the needle, it's round, it's like cutting a piece of bread
with a rounded stick. So instead you should grab a x-acto knife, because it is sharper,
set your angle, and then just cut straight down through both of the coils.
Peel away the clay you don't need, and then your beveled edges should line up very nicely.
It's a little bigger on one side, but I'm going to end up adjusting it in a tad bit.
And from here, I'm just going to go ahead and line it up a little more. I'm going to take my
needle tool, I'm going to spin the wheel, I'm going to generally mark where it's going to attach,
so I know exactly where to scratch and score. So I'm going to take my coil off at this point,
put it on the side, and now I can start scratching and scoring this area.
So I can take my needle and just kind of do zigzags, and this will take a little while,
so if you do have a scratch and score tool, now's the time to bring it out,
and I'll show you what that looks like. This is a scratch and score tool that I like,
it's very similar to like a rake, and it has a bunch of little small wires, and when you scratch
and pull, you create a lot more marks than with a needle. So I like this because it just takes a
lot of the time away from scratching, and it just speeds up the entire process. So if you
are going to be making mugs or any attachments as you throw, I highly recommend you pick one of
these things up. They're only like five dollars, possibly less. Keep in mind, they do sell these
on Amazon. The ones I got on Amazon, they're not as good. The metal is a lot less rigid,
it's softer, so you probably want to pick one up at your local pottery store.
I think this specific one is a Kemper. So I scratch and score that entire area,
and so for those who haven't attached pieces of clay together, you always want to scratch and
score, which is basically this cross-hatching action. The more textured it is, the more messy
it is, the stronger the attachment will ultimately become. Now some people get away with scratching
and scoring just with this general checkerboard or hashtag. I'm not a fan of that. I've seen a
stick, so I don't really recommend scratching and scoring like that. And the next thing is
scratching and scoring the coil, and like I said, the messier it is, the more little clay particles
pop up on it, the stronger the attachment can ultimately become. And then the next thing you're
going to want to get ready is either water or slip. Now if you don't have slip, you can just
use your throw water. That's basically slip. Slip is just liquid clay, and you don't really need to
add anything in it fancy. And then, of course, scratch and score the two ends. That's where we're
going to attach these together. The next thing is applying the slip. So that's where the brush comes
in, and I don't recommend brushing on the slip, because if you brush it on, you end up smoothing
all your scratch and score marks, so it kind of takes away all the work you did. So instead,
I recommend you dab it on. So to speed up the process, I spin the wheel, and then I just dab.
And the thicker the slip, the stronger the connection can ultimately become.
Some potters, they just use water, and it works with them, but if this is the first time you're
doing this, I recommend getting the thickest part of your throw water. This is kind of watery,
but the thickest part, so it's the more, it's almost like yogurt consistency, and then it will
be a stronger connection. Okay, so I'm going to be very generous, because I definitely want this to
stick and not shift on me. If you want to see more ceramic videos, don't forget to like and
subscribe. That way, it helps grow the channel, and you'll be able to see these videos as they're
released every week. And now, I'm going to go ahead and place the coil on top, and get ready
to then blend and attach. So I'm going to start with the opposite side first. Make sure the
scratch and score marks touch, and then basically line it up and start compressing. So line up the
they're more or less exactly where you want it, then you can go ahead and start compressing.
I forgot to put slip where they attach, so I'm going to jam that in there real quick,
and get those together. You can start blending those two ends, and don't worry about the
unevenness of your coil. We're going to end up throwing this to even it out. Okay, so what I'm
doing is, I'm just compressing the clay down, and I'm just getting it nice and stuck. Next thing I'm
going to do is, actually, I'm going to start pushing the clay down here to blend it into the
clay body. So spin the wheel slowly, or you can just let it do it when it's not spinning.
I'm just going to push that edge down, and I'm going to have to go back again, because I missed
some spots. This area is a little thin, so I want to kind of push and really blend that clay together.
So the more secure and stuck this is, the easier your next step will be. So really make sure that
you push it down and compress, and the next thing is compressing the outside. So it's always good
to do both sides. Now some people get away with just plopping it on and start throwing it, but
I like to take the extra step, especially if this is your first time trying it.
Go through all the steps, and then as you do this more, you can remove steps that you feel
were not needed. Okay, so that looks pretty good. So first thing is, I'm just going to compress,
and then before I do anything, I'm just compressing and making sure that this clay is
fully blended, because I don't want to do anything to this in terms of pulling or thinning until
everything looks perfectly blended and secure. So below where I attached it, I'm going to add
a little water and ensure that it's nice and blended. And one thing to keep in mind,
my clay was a little on the drier side, and so if your clay that you're attaching, in this case the
coil, is really wet, and your clay that you're trimming is really dry, you may have some cracking
issues. So ideally, you want your leather-hard trimming piece not too dry. Okay, outside looks
decently blended, now let's blend the inside. There we go. So I'm spinning the wheel and doing
another compression now that they're really blended, and that is basically attaching your foot.
So at this stage, you can play around with it, and I'm going to thin this out just a little bit more.
This is a little too thick for me, so I'm going to go ahead and cut a little bit off of it,
and that way it'll level out. And just like when you throw your rim on a wet clay,
you're just leveling it out. Now I'm just going to throw this a little more. I'm going to really
push that clay and then thin this out, because I want a taller, thinner foot, and then I'm going
to trim it to exactly how I want it. All right, there you go. Now let's trim the outside, and
because it is wet, it's going to get a little sticky. Apologies for the helicopter, we have to
wait till it passes. It will get a little sticky, so this part does take a little more patience.
If you want, you could use a heat gun or a torch to dry the clay, but for demo purposes,
I'm just going to chug along. Okay, outside looks good. Inside, I'm going to round this a little
more, and if you wanted to trim down the inside, now would be the time to do it. So I want to take
a little bit off. This was thrown a little on the thinner side, but I just want to kind of even it
out, so there's nothing wrong with removing extra clay if you know that you have the clay to work
with. So I'm going to go ahead and work on getting this sloped to finish off the foot. There you go.
Now that's a cleaner edge. My foot looks a little more defined now. Now let's clean this up even
more, and let's get that undercut back in on the outside. Now this one's going to be really wet,
because this is the clay that I just attached. So definitely take your time. It might get a little
frustrating, but as long as you're patient, you got this thing to look amazing. Okay, I'm going to trim
away all that excess clay that got stuck, and I have a little more to touch up, but that's
basically it. Very thin. I'm going to take a little bit off of the outer edge to kind of get that slope
back, and remove all the excess trimmings I don't need. Let's clean this up, and we'll call it
pretty much a day with a sponge and final smoothing. Now like I said, trimming the inside is not
necessary, especially if you do it thin. I just wanted to adjust it to make it a little more even.
So now I'm just doing the final touch-ups, and I'm removing all the little clay bits that just
got stuck because of the moisture added to it. So just using the trimming tool as a rake to collect
all the little bits, and then I don't really recommend just trying to blend them in, because
you'll have these weird bumps in the clay, and it's much harder to smooth it out once there's bumps.
All right, lastly, last bit of smoothing, and then just kind of smooth and burnish the areas that I
want to remove any unwanted trim lines. All right, and then there we go. I have my attached foot,
and this works really well if you want a really, really tall foot. I wanted to add another
half inch to it, and so I do like this method when it comes to attaching a foot and not having to
throw a very thick bottom. It does save you clay and trimming. It does take a little more time to
attach, but I think the final outcome does look pretty awesome, and if you were to show this to
anybody, I'm pretty confident that they would not know that this was attached. One last tip,
because the clay that you attached is going to be most likely wetter than the clay that you trimmed,
I do recommend you cover this in a bag and then let it kind of equalize in dryness over the next
one to two days, and so that's the only downside is it does take a little longer for this to kind
of dry and settle. Now, if you do let it air dry and pop it off as is, most likely you'll see cracks
develop where they attached, especially on the outside and the inside, so we don't want that.
Wrap it up in a bag, and if you do that, definitely pop the wads off before you do that. Wrap it up in
a bag and then let it sit for at least a day or two before you let it air dry to get ready for
the kill, but other than that, I have my piece. I'm going to go ahead and wrap it up in a bag,
let it sit, and then we'll see how it looks in a day or so. So here's the platter that we
attached the foot to yesterday, and I didn't follow my own advice, and I forgot to wrap this
up, and it was sitting out overnight, and it did dry quite a bit, but one good thing is it did not
crack, so because I really compressed it out of water and I trimmed away the excess, it helped
reduce the chances of cracking, and I could potentially leave this out overnight again to
let it air dry completely before I could put in the kiln, and that's basically it. Thanks for watching
guys, I'll see you guys in the next video. If you want to see more ceramic videos, don't forget to
like and subscribe, that way it helps grow the channel, and you'll be able to see these videos
as they're released every week.
