Look What I Did To My Friends Car Ultimate DIY Camping Conversion

And More
49 followers
18 Video Views·Oct 19, 2022
This video was sponsored by Skillshare.
In a world with cars, one boy set out to become a man by transforming his car from a wagon
normally driven by a middle-aged female into an awesome camping mobile. That boy was...
my friend Nathan. You want me to make this look cool? It's a Subaru Outback.
I gotta level with you. I've never done anything like this before in my life.
It's way out of my wheelhouse. Pun intended. Thankfully, Nathan had full confidence in my
abilities. He knew I'd get it done one way or another. Don't need that. The first thing we
had to do was get his car inside my shop. Unfortunately, my shop's not really set up
to get a car inside, so it was a little trickier than you might think. But Nathan is an extremely
experienced driver, so we got it done in the end. Once it was in the shop, he was a little concerned
about his bodywork. I was more concerned with the interior of this thing. Like I said, I've never
done anything like this before. Cars are just a foreign subject to me, so I didn't really know
where to start. But I figured making some templates so that we could get a flat surface to build off
was probably a good jumping off point. Luckily, there were these detachable pieces we could use
as templates towards the back of the car, but I still had to figure out the front section.
So I just grabbed some brown craft paper, and my plan was to just kind of bend it roughly
into the right position, and then use a pencil to draw my line. I knew this wasn't going to be
perfect, but I thought if I could get it close, well, at least it would give me some place to
work off of. So after making my first initial cuts, it was pretty close, but it still needed
a little work. So I trimmed a little down here or there, and before too long, I had it fitting
actually surprisingly nice. Next, I wanted to take that front template and the back template and put
them together in one giant template on something a little more rigid that I could be just a tad more
confident in. So I transferred those shapes onto a piece of rigid cardboard, just with a sharpie
marker, and then I cut it out with a razor blade. This would also probably be a good time to calm
your nerves about that spare tire. You saw me chuck it aside. Don't worry, that will be mounted
conveniently on the roof, so we won't have to worry about accessing it once we're all done.
With my template cut out, I took it back over to the car just to double check and make sure that
it fit like I wanted it to. And it did! Almost perfect. I said almost. There are a few little
gaps, but I just took some blue painter's tape and taped them right onto the template to fill in
those gaps, and then my tape will essentially become part of my new template that I can use
to trace out my final shape. Ooh la la, I'm practically a car guy now. Then before I started
actually cutting pieces out of plywood, I wanted to double check and make sure that it was identical
on the opposite side. I don't know, could be different. Who am I to just assume that both
sides of the car are the same? But it was. Next, I had to figure out how wide we wanted to make
this thing. One side was going to be cabinets, the other side a sleeping area. But how wide do you
make a sleeping area? Well, I guess it kind of depends on the person. There's got to be somewhere
I can get measurements from. That's when I snuck up to Nathan while he was looking at his smartphone
and got measurements right from the source. That's right, I measured Nathan's backside,
added a few inches to it, and that's how I determined the measurements for our sleeping
area. Turned out to be about 25 inches. That's right ladies, 25 inches. Finally, with our template
done and our measurements secured, I took the template over to a piece of three-quarter inch
birch plywood and I traced the shape of the template onto the edge of the piece of plywood.
Then I ran the plywood through the table saw to get the width that I was looking for,
and finally I cut out my template shape nice and easy with the jigsaw. This actually wasn't nice
and easy. It was kind of a pain, so I was really hoping this thing would fit the way it was supposed
to. So after finishing my cuts, I took the piece back over to the car and inserted it in wooden
it fit perfect, until I realized a huge horrible mistake. Now I knew from the beginning that we
were going to have to prop this back end up to make the whole surface level, but what I didn't
think about was as soon as I propped it up, it's going to throw that scribed side completely out
of whack. So we thought about it for a little bit, pondered, and then I quickly realized the
only thing to do was to prop it up, redo the template, and re-cut another piece. Gosh,
what a moron. So much for being a car guy. So I quickly threw together another template,
I traced it out on some more cardboard, I cut it out with a razor blade, and it was back to
cutting it down off of a new piece of plywood. This part was actually kind of a pain, so I
really hope it fits. Man, I feel like I'm having deja vu or something. But as my father always said,
why measure twice and cut once when you can measure once and cut twice? But he wasn't a
woodworker, so probably why that doesn't make much sense. Luckily, our second attempt fit
very nicely. Next, we had to determine the exact center of the car so that we could get a nice
square cut along the edge of our plywood. I didn't know how to do this, because nothing
in this car seemed square. We're dealing with all curved and rounded angles. But I figured
that little ring at the back of the car was smack in the middle. So I tied a string around that,
and then I had Nathan hold the other end of the string on the very center of the shifter knob.
I assumed that was also in the center of the car. And then I cut that line with the track saw,
just praying that this was all gonna turn out okay. Then I measured the space we had left,
which was that 25 inch rear end space I allotted for before. And I thought it was high time Nathan
start doing something, so I made him carry this piece of plywood over to the table saw for me.
Get going, man. This guy. Then, confident that the other side would be identical,
I used my original piece as the new template, and I traced it onto our new piece of ply.
And then I did the exact same thing I did on the other piece, just on the reverse side. I cut it
down to length, I trimmed the whole thing out with the jigsaw, and boom goes the dynamite.
I think you're gonna see me doing a lot of things in this video and wondering,
where the heck is Nathan, and why isn't he helping? But that's okay. I've gotten very
good at working all by myself. By the grace of God, the next piece fit in perfect, and our
squaring method on that seam seemed to have been accomplished flawlessly. I should probably stop
and tell you about some of the components going in the car. A yacht battery, a roof-mounted solar
panel, we've got this thing, and this thing, ooh, and of course, a refrigerator. That's right,
all that will get in here at some point. With our plywood base cut to the right size,
I could now start fitting it a little better. Now, I knew I had to lift it up on the back,
so I had to figure out some way to make a tapered base that would keep it level and give us a sturdy
surface to build off of. So, I took some pieces of plywood over the table saw, and just using my
nice and simple tapering jig, I cut them down at a taper that would perfectly match the underside
of those base plates and sit flush against the car. Kind of like this, giving us a nice level
surface to build off of, as well as some additional space on the bottom to add a bit more storage.
But, we'll get to that here in a little bit. First, I wanted to trim down the back side of
both of our base plates to have a nice straight edge to work off of. Next, I had to figure out
a way to integrate our tapered brace pieces into our top base plate. So, I cut down some little
connecting brace pieces just out of three-quarter inch plywood, and I used them to connect those
brace pieces together along the bottom. Kind of the same way you would if you were building a
ramp for you to jump your BMX bike off of. Oh, this brings back memories. And once again, Nathan was
diligently working hard while I got everything put together. Because this is going to be on the
bottom side and you're not going to see it, and also because it's going in the back of a Subaru Outback,
so who really cares, I just glued and screwed everything together to make it quick and easy
and super sturdy. Then, once it was all hooked together, I flipped it over, applied a little
quick and thick glue to each of the top surfaces of those brace pieces, and I laid the template
smack down on top. And then, because I'm a fine woodworker, I just screwed it right down to the
brace pieces through the top of the ply. I did use trim head screws though, so they're not that
noticeable. And then, I carried it over to the car and slid it in place to see how it fit. Hey, hey look,
Nathan's helping. Man, I'm gonna make a woodworker out of him by the end of this video, I swear
on my life. Maybe not my life, that's pushing it. Anyways, after getting one side done, I did the exact
same thing to the other side. I secured the base with those brace pieces, added some glue, and screwed
down the top. Then, I carried that over just to make sure we were still going to be able to slide this
whole thing into place. It was a little bit of a struggle, but we got it in. It was also our first
attempt. We'll get better, just trust me. We're unseasoned at this point. So, with our two base plates
leveled out and fitting nicely in the back of the car, it was time to start working on the upper
cabinet storage. Now, the idea was to do one long drawer that would pull out the back with built-in
cabinets on top of that. So, I started just quickly making a frame for that drawer. I simply took some
3 quarter inch plywood, added some pocket holes, glued it onto the top, and secured it in place.
Nice and simple. Remember, this is going in the back of a Subaru Outback, people. No need to get
too fancy here. After getting one side on, I glued and screwed in place the back piece, making sure
that it was nice and square to that first side. And then, after I got that securely fastened,
I added my other side, gluing and screwing that in place using this little spacer block as I worked
my way towards the front to ensure that everything stayed nice and square. That will make installing
the drawer much, much easier. This video was sponsored by Skillshare. Skillshare is an online
learning community with thousands of inspiring classes for creative and curious people.
Explore new skills, deepen existing passions, and get lost in creativity. I just took a very
helpful class on video for Instagram taught by Hallease Nerveas. Hi, I'm Hallease, a digital
storyteller and YouTuber, and ever since I bought my first camcorder at 12, I've been making videos.
Whether you want to say a lot or little, filmmaking is a really strong... With every class I take, I'm
learning something new, and there are so many great topics to choose from, everywhere from
animation to photography to productivity. Hey everybody, my name is Thomas Frank. I am what you
might describe as a productivity nerd, and in today's class we are going to be building what
I like to call a productivity system. Even if you say productivity funny, Skillshare has something
for you. It's curated specifically for learning, meaning there's no ads, and they're always
launching new premium classes. To top it all off, it is less than $10 a month with an annual
subscription. The first thousand of my subscribers to click the link in the description will get a
free trial of premium membership, so you can explore your creativity. With a frame of our
lower drawer basically constructed, I decided to set that aside and start working on our upper
cabinet boxes. Now these cabinet boxes will be made as quick and simple as you could possibly imagine.
Back of the car, people. So I cut down all my pieces on the table saw and took them over to my workbench
to start hooking them together. And how did I hook said pieces together? Just with glue and a 16 gauge
pin nailer. That's right. Fancy, fancy, fancy. In order to save space on these cabinets, the bottom of the
cabinet will be the top of the drawer, and the top of the cabinet, well, will just be a thin piece of
quarter inch ply I will put on later. I made a nice compartment for the fridge, a little shelving
unit, and then that far section will be a cabinet door. While I finished up on the cabinets, I
convinced Nathan to do a little work and start drilling a zillion holes into the... Stop dancing,
Nathan. This isn't your video. Into the sleeping section of the compartment. After drilling the
holes, I had him hit each hole with a little roundover bit. You know, just to get rid of any
splinters. Don't want him to get splinters in that 25 inch backside of his, if you know what I mean.
By the time he was finished drilling holes, I was ready to hook the cabinet together. So I had him
hold it in place while I just glued and tacked everything down. I tacked the top of the lower
drawer to the bottom of the cabinet unit, and we will put that in place after we secure our drawer
slides. I wanted to leave the top of that drawer open so we could easily access those slides.
But before we do that, I had to build a drawer. So I quickly threw together a very oversized drawer
just out of Baltic birch plywood. Now this drawer is going to be a little special. It's super long,
so it's going to pull out creating a table slash cooktop work area. So one section is going to have
a Coleman camping stove, and then the other section will just be more storage. But we needed a
tabletop. It had to be flat so you could work on it if you didn't want it just to be an open drawer.
So while I figured out how I was going to make that happen, Nathan got to work on the electrical
setup for the solar panel and yacht battery. To make my tabletop drawer, I just took a quarter
inch rabbeting bit, and I added a rabbeted groove to the inside of each one of our drawer sections.
This kind of was a dusty job, but what are you going to do? With my lip rabbeted on the interior
of each drawer space, I took this little corner radius marker thingamabob I had laying in a drawer,
and I traced out the radius of each corner onto the piece of quarter inch plywood. Then I took
it over to my oscillating spindle sander, and I just knocked it down right to the line. I drilled
out a couple holes in each panel so you could stick your finger inside and pull the panel up
if you needed to access the drawer. And I took them over to see how they would fit in the top
of the drawer. And wouldn't you know, they fit perfect on the very first try. Sometimes you just
get lucky. Or maybe sometimes you fit them off camera first and don't show your viewers. But
we won't get into that right now. With our drawer built, it was time to install our drawer slides.
Now these are these crazy heavy duty industrial side mount drawer slides that supposedly will
up to 300 pounds. And to be honest, I don't doubt it. They almost weigh 300 pounds. So after securing
them inside my drawer carcass, I slid my drawer in place so that I could securely attach the slides
to the drawer itself. Now I wanted to raise the drawer up off the base a little bit, so I just set
an eighth inch little spacer block under the drawer. And I slowly pulled it out as I secured
the slides to the side of the drawer. And of course you want to make sure that the drawer's
not too tall, because we do have to put a top on this thing. After I got my last screw in place,
I tested and wouldn't you know, the drawer slid in nice and easy. And we were ready to close it in
with our upper cabinet. And then I just secured it to our drawer carcass with a few more trim head
screws right through the top. Sure you're going to see them, but big whoop. It was about this time
that I just started hating this corner that was going to make up the box to hold the fridge.
So I decided trimming off one corner of it would make it look a little nicer. And you know what?
It did. It really did. Then finally I wanted to add a few little strips to the front to keep the
fridge from sliding out, as well as keep anything tucked inside those little shelves from sliding
out while Nathan drives around on bumpy roads. Or more accurately in his case, down the rough streets
of Portland, Oregon. Then we tested to make sure the fridge fit in nicely, which it did. Probably
because we measured to make sure that it would. And then again in an effort to save on room,
I just added a thin piece of quarter inch as a top to our cabinet box. Then finally I cut
a little three-quarter inch square to act as a cabinet door. And I secured it in place and added
a nice black little pull. Because Nathan deserves the best. I love that guy. And the very last step
was to add a drawer face to this long pull-out drawer. I just made one quick and simple out of
a piece of five-eighths baltic birch. Then we carried the whole monstrosity over to the car
to make sure that it wasn't too tall. That would be a huge bummer. We would never ever make a mistake
like that in our lives, would we? I was really building it up there to make you think that it
actually was going to be too tall, but don't worry. I took very strict measurements after our first
template debacle and it fit perfect. Then we grabbed our other base piece and slid that just
to make sure we could once again slide it in now that it was much taller with those cabinets. And
we're getting a lot better at this. It popped right into place just as it should. Look at that drawer.
Pulls all the way out, creating a nice tabletop surface with a little storage. Speaking of storage,
I thought it was high time we put something in these holes we created when we leveled out those
base plates. Now I used side mounts on that long drawer, but I just couldn't bring myself to do it
again. I had to get some blum undermount drawer slides in here somewhere, and 15-inch slides fit
perfectly in these little holes. So I installed the slides. I threw together a few more drawers
just with five-eighths baltic birch. I installed my little orange clippy things, rammed them in place
to mark out where that little clip on the back needs to go. I drilled my corresponding holes, and
I slid the drawer in place. Click, and just like that, two more storage spaces for Nathan to store
his socks, or underwear, hatchets, or whatever else you need to go camping. All they needed now was
some drawer faces. This was a little more complicated because the back of the car curves in
on the corners, but I just slid a piece of ply against that curve, and then using a pencil as a
scribe right along the edge, I just scribed out the exact shape of that little corner radius, took it
over to my bandsaw, and trimmed it down. Almost like I knew what I was doing. Then I cleaned it up
once again on the oscillating spindle sander. Now here's a little trick for installing drawer faces
in any application. If you know what hardware is going to go on the front, you trace out exactly
where you want that hardware to land, and then once you get your drawer face lined up,
you just send some screws right through those markings of where your cabinet hardware is going
to be. Then the drawer face is securely attached. You open the drawer up, you screw it in from the
inside with a few screws, and then you just pull out those screws you used to attach the drawer
face originally, and you pop on your hardware. No one will be the wiser, and you don't have to
fumble around with any clamps or double-sided tape or anything like that. I don't use this
in every application, but it comes in handy when you need it. So I did the exact same thing to the
other side, and boy, we lucked out with this hardware. When the back is shut, that hardware
is about an eighth of an inch from the back, which ensures that those drawers will stay closed
while you're driving down the road. Unfortunately, the same could not be said for this long pullout
drawer, so I decided to install a little clip lock thing. This actually is supposed to go on the
bottom of a table to hold the leafs together, but I thought it would work great to hold this drawer
securely. I mounted it on the side, so you can just flip it, open the drawer, and lock it in place.
Hey, if it works, it works. Oh yeah, I also forgot to mention at some point we installed a
bottle opener, because duh. Because I know I'm going to get a hundred questions from people
asking how long does it take to put this in and pull it out, I thought I would just show you in
real time how stinking quick you can take this out and put it back in. Now, I wanted to do a
fancy countdown clock in the corner, but I don't know how to video edit very well, so this dumb
little clipart graphic is the best I could come up with. But rest assured, I am keeping a timer,
and I will show you the total time here in just a second. Wait for it, wait for it, wait for it,
and it's out. 37 seconds to take the whole thing out of your car. And how long to put it back in?
Well, we can do that too. Let's go. Little clipart clock, do your thing. Now remember, we are very
practiced at this point, because we've been pulling this in and taking it out. It is a little heavy,
but with two people, it's really not bad at all. It's not screwed in or clamped in. It's just held
in place by the pressure between those two separate pieces. So once you get your left side
cabinet piece in place, you just grab your little sleeping base plate thing, and you slide that
right in. Then while somebody holds the front, you just do this, do that, wiggle here, wiggle there,
shimmy, shimmy, shimmy, shake, shake, shake, and boom, it's in. Okay, stop the timer already.
Hello? 53 seconds. It's a little less. My timer skills aren't that great, but you get the idea.
Under two minutes to take it out and put it back in. Can I get a boom? Although I wasn't involved
in this process too much, I thought I would show you the simple components that make this whole
setup a little more functional. There's this solar panel on the roof. Now eventually, Nathan's going
get a roof rack, so we didn't want to permanently hook this on, so I just used zip ties. But
basically, you've got a positive and negative cord coming off of the solar panel to a controller. The
controller runs down to the yacht battery, and then the yacht battery runs back up to the inverter,
which changes it from DC power to AC power. And that gives you power for your refrigerator,
as well as a little plug in the back in case you want to plug in an electric kettle or
charge your phone or do whatever you weirdos do with power when you're camping. I've never had
much use for it myself. And then the cord from the solar panel just gets shut right inside the door
like that. And last, we added a few of these little battery-powered touch LED lights in a few
handy places. One in the back above the pullout table, one inside the sleeping area that you can
turn on while you're reading or I don't know what else. And they're on a remote and surprisingly
bright, so you can turn them on from anywhere you want. They also have a party function in case you
want to get groovy up in here and set the mood lighting. Seems kind of weird, but hey, some
people like it. And with that, there was only one thing left to do. Take it outside and see how she
handles. So with drinks in hand and my good buddy Nathan by my side, we enjoyed the great outdoors.
At long last, my wagon-loving boy had become a man. I knew we should have made it bigger than 25
inches. This is ridiculous. I'm not going to say it again. Get your feet out of my face.
I can't do this again. Get a bigger car.
