One of my pet peeves about Lionel Trains O and O27 gauge lighted cabooses and passenger cars is the flickering lights. Watch as I fix this problem on my Postwar Lionel bay window caboose. While I was at at, I added LED marker lights, a rear flasher, and a custom 3D printed inteior!
**As an Amazon Associate and a member of other affiliate networks, We may receive commissions on qualifying sales generated from the links on this channel.***
Timestamps: 00:00:00 Introduction 00:09:18 Discovering The Problem 1:20:05 Inspiration! The Observation Car 1:59:10 Basic Interior Lighting - LEDs and Resistors 03:24:24 Preparing The Interior 04:58:01 Drilling For Wiring 06:44:20 Drilling For Rear Flasher 08:42:02 The Buck Converter 09:54:24 Main Power to the Buck Converter 11:05:14 Adding The Figures 11:57:15 The Lighting Bus System 14:51:21 The Quick Connections 15:41:04 Add The Bus Assembly To The Ceiling 15:52:13 Mount The Markers And Flasher 16:46:22 Wiring The Negative Feeds 18:03:26 Wiring The Positive Feeds 20:36:00 How It Works 25:53:21 My Caboose vs Traditional Lionel Demonstration 25:59:20 Summary 27:57:08 On The Layout
Toy Train Tips And Tricks is a channel devoted to the operation, repair, history, and collecting of classic 3-rail O and O27 gauge trains made by Lionel, Marx, K-Line, Menards, and other manufacturers.
Protect your rear end.
Flicker free LED lighting upgrades for Lionel cabooses
on this episode of Toy Train Tips and Tricks.
And hello again this is Mike with more Toy Train
Tips and Tricks.
So in the last video, the Tropicana Cars, I had this Lionel bay window
caboose on the end of the train
and as I was running the caboose around and taking the video
I really didn't like what I saw.
The lighting that I had added, it was flickering, and it just didn't
look right to me. So some of you will remember
when I first picked up this caboose, I believe
it was this past spring. It was at a show, and it was kind of abused.
Not all of the the smoke stack,
the detail parts were missing.
It didn't have any interior lighting, didn't have any windows,
and I believe it even had a coupler problem as well if I remember right
so I fixed those things
and the end platforms and railings were missing
so I replaced the platforms they're not on it
right now because I had it apart in pieces
but I replaced those I added some automotive type
bulbs to the interior got these detail parts going fixed the coupler
but I got to thinking
remember these three millimeter LEDs that I used for my observation car
project well it turns out
this three millimeter LED is just the perfect size
to fit in the hole where these Lionel marker lights go
so you see it's a
perfect size to fit in there
so that got me to thinking why not replace the
lighting that I had previously added
with some flicker free lighting to get
rid of that that is annoying to me
and while we're at it let's add some LED
markers, and let's add an interior.
So let's get on with the project.
Okay, so first let's start
with the lighting. Instead of having
the big lights posted here on the bottom, I'm going to
have three LEDs attached to the roof,
and that should give us pretty even lighting all the way
cross pulling out my five millimeter leds one two
yeah now i got one now in order to cut down the
brightness of these bulbs we're going to add
a resistor to the positive link of each one of
these i'm going to do that before i install them i want
these 1k resistors these half watt 1k
resistors one on the positive
which is the longer of the two legs of each led and the resistor has
no polarity doesn't matter
which side connects each one has to do that the mine might no longer
works on this after what three years four years
but it still works really good it heats up really
fast good and hot add
my heat and my solder
one two three four it's
two three white LEDs
here's our rather basic interior i'm going
to be able to see much through the windows anyway
added a quick coat of an industrial green
and yeah i didn't clean this up as well as
i could because again i don't think anybody's going
to be able to see the floor through the
windows anyway so i didn't worry about cleaning up
these little nubs let's add a little bit of
color so some of these details can be seen better let's go
with some gray that'll should pop through
doesn't have to be the best paint job in the world
and with my hands it won't be the best
paint job in the world by the way
this is deco art amish gray i don't remember if i got this at
walmart or leather king from hobby lobby
but it's that kind of cheap acrylic craft paint that you
find in the box stores the details are pretty good keep
in mind this was originally an HO scale
model that i blew up and i'm going to keep it top
but do something other than this gray crap
smart brown all right i'm gonna let that dry
then i'll come back and i'll put my figures in
okay now to finish up my interior base notice there's two holes
in the bottom of my interior
one is to let the wire from the center rail pickup come through
the second hole i am going to
put a machine screw and a washer on there
and that is going to be my contact to ground the
frame this has metal trucks
so the frame is on the ground side of the circuit so i'm going to
run a screw through that and then attach
my ground wire to that and that will also
i'll keep my interior from floating around it doesn't have
to be a huge hole but i'm going
to use that as the spot there we go
and up there i will run
that through there and then i'm going
to attach ground wire to that and lock it down
and even though i'm going to crimp it i'm going
to solder it too just to make
sure there's a tin on there
solder even right nice hot low
i guess up in the bottom so this is now attached
to the frame i have a wire going to the frame
okay so this is from the center rail
this is from the outside rails in the frame so that's our wiring
connections from the track all right
so while i have the drill out as i mentioned before i'm
using the three millimeter LEDs here on the side markers
but i also want to put a flashing strobe
on the end so i want to center it above
this door you can see in pencil i've marked an x so i know
exactly where to go and i wanted a drill bit
that is just slightly smaller slightly smaller than the
five millimeter LED so i don't know if you can tell in here
but this is tapered so the tip
is smaller than the base
so if it's a little bit smaller you can get the tip in there but
it shouldn't need to protrude all the way through
to the base you get it a little bit too big well
a little bit more of the bulb will show not a deal breaker
when it's hidden down here but i don't
want that whole bulb in there i want about
that much peeking through i'm going to line this up
with my x i'm going to slowly drill my hole
and then i'm going to erase my pencil marks
there we go all right let's come back and erase
so you can see just the tip of the LED is poking
through a hole and i'll secure it there
and that way we don't have this big massive bulb there we
just have our flashing light the three millimeter
if you look very closely right here that little
bulge that is a resistor this is already pre-wired
to handle 9 to 12 volts so i'm good because i'm
going to be using a buck converter to knock not only the AC to DC
but knock it down to guess what
9 to 12 volts so this is all set ready to go
and this one is preset this is a blinker though the
sides will be constant this one will be blinking
and we are good to go with that all right this
is the thingamabob that does the job this is an AC to DC buck converter
and the output again is
variable 9 to 12 volts right here that little screw
is the adjustment to adjust the output
so when we get it ready to go we'll test
that so basically these two if you look on the bottom
they're marked AC this is our AC inputs
and then these two this is DC negative this is DC positive
so that's all you need to remember negative
to the outside DC the inside got your capacitors
heat sink so it does have a little bit of a capacitor in it
so it will have just with this
is going to have a little bit of a non-flicker effect i'm going
to add a little bit more actually
i'm going to add a whole lot more capacitor
to it i really like that feature plus i have a huge
4700 micro farad capacitor we are just going
to attach it it doesn't matter which of these go to
which one AC AC what will matter is the output for the DC
so i'm just going to screw these up
i've got a little bit too much wire exposed
so to cinch that up i'm going to cut the tip off here
when we are down to the insulation tighten
our screw and that is one side now i'll have to do
the same thing on this side okay and we will
position that right about there i am going to use
my favorite Gorilla Poster Putty to hold this in place
and to get these wires down and out of the
way too this is non-conductive
so i don't have to worry about anything shorting on the bottom of
the board but this will hold the board in place
so it doesn't go wiggling around rattling around
on the track and i doubt you'll be able to see
that through the window great thing about this
stuff is it is totally removable you can do it again
let's push that wire there is that wire there
okay so we're good from the track to our ACN we're going
to hold off on the DC output for a moment
one more thing we could do on the interior
though is let's add some seated figures so on my railroad
it's 1977 we still have a full five-man crew
so here in the back we would have our conductor and
our rear brakeman so we got two guys here
these are these Evermodel seated figures got off the
internet. And so, you know, this guy looks kind of bored.
He's leaning on his elbow on the armrest
there. He would be a good conductor, I think.
And this guy is also just kind of staring out the
window. I don't know what's going on or whatever.
I'm going to go ahead and glue these guys in place
so they don't pop off and start rattling around
on the seat and on the seat. There we go. We're
going to set this aside. Now let's go back to our shell.
I'm going to have these three LEDs plus
three white LEDs for light all going through here
and they're all going to be wired in parallel so
to make it easier on myself i'm going to have two bus lines
a negative on one side a positive on the
other before i do that let's get two long strands
of solid wire that i'm going to use as my bus
wires and i'm going to pre-wire all of my leds to those two bus wires
and then mount the whole
system in there all at one time yeah about a long
again same length and then both of these are going
to get stripped bare and do this a
little bit at a time so by doing it
a little bit at a time it's
a little easier to pull as you can see i'll have
the resistance of that entire length of wire
pulling against the insulation it really doesn't matter
which one is which call this one positive
we're going to call this one negative with these mounted
in the roof this is not going to have very
far to travel so let's cut this short okay
and we'll call that positive and that negative and
so one's going to go here one's going to go here
so one of them will really need a short negative
and a longer positive so this one
will go like so and then this one
the opposite i need a longer
negative so roughly and then we
have our three whites this is
a positive side on each so i'm
going to trim up off of that resistor
but these are basically going
to go like so so and so so
i'm going to go ahead and pre-solder all of these connections
then i'm going to mount this into the
roof of my caboose one thing i almost forgot to connect the top
and the bottom so that i can take
the shell off of the frame
and do maintenance i want to use these quick connects a male and a
female and i only need two
of the four wires normally i would just put two of them off but
in this case for redundancy i'm going to go ahead
and bundle two and two just to make sure so that
if one of these fails i will have a secondary connection
to make sure that that works here
all my negative side connections on my negative bus
and now i will be the same with the positive
connections so now my positive side is also soldered up
so now all i have to do is to mount
this into the ceiling of my caboose
and i'm done with everything i'm going to do with the shell
that would include putting the LEDs
in their proper place i'm going
to test fit this before
i secure it down let's put these in their place
so let's start with the one in the back and i'm
going to put just a little bit
of my favorite silicone type sealant in here just to hold these
in place because my fingers
are too big to fit down
in there all right that one is in place
all right let's pop the other side all right
that's going to light up those markers really
nice. Now, just to make sure that my plane around
this doesn't knock those loose, I'm going to let
that silicone dry.
Meanwhile, while that's drying, let's move back to the base.
The negative side,
all I have to do is run from the negative here,
runs to the negative side of the capacitor,
and runs to the negative side of my lights through here.
So that's all I have to do with the negative
side, so let's do that first.
And actually, as I do this, I'm going to make one change
to what i said about my four here instead
of doubling them up i'm actually going to
split these up into four pieces
so that my positive one side is going to come right from
the buck converter one is going to come from the capacitor
so we're going to run from the negative
to the negative to my LEDs
no wire showing tie it down
so my black
and yellow tails i'm going
going to combine them here
and attach right there.
And I've got plenty.
Now on the positive side,
the DC positive coming out here,
there's actually going to be two connections. One I've already done
just coming from the DC plus of the buck converter
and it is going to my LEDs through my red wire
that goes to my quick connect to go to the LEDs.
That's one side. The other side, let's work
backwards. From the LEDs,
remember the other side of my LED positive is this white wire.
The white wire is going to connect to this diode.
This is a 1N4002 diode. You can also use a 1N4007
and notice there is a stripe on this side.
The stripe side is going to connect to the white
wire stripe side to white wire
so let's do that now stuff keep
hot slide or you trip up here
that's not going anywhere now
the other end of the diode is going
to go to our positive side
remember this was the negative side over here
to the positive side of this capacitor okay so we're
almost finished with the wiring
but again there's one component we're waiting on for the amazon
truck coming tomorrow.
So I pre-wired where that component is going to go.
So you'll notice now
there is a second wire coming from the DC positive
and it goes here and then that component will go
here and here. It's a big resistor and then it continues on.
Here's our capacitor and then this
goes up to our LED lights. Amazon came
and so I installed my resistor of unusual size. This is a
one watt 22k ohm resistor now most of my other resistors
for this are half watts so that's what
I keep in my parts bin but I needed the one watt
for the amount of current that we're drawing here
so let's go through the process of what happens
and what these components do so we get our power
from the track it comes in to our ac input runs
through here it's converted into dc and a steady
output the steady output is adjusted here now i adjusted mine using
my volt meter before i put
it here to set it for nine volts if you need
to adjust it it's this screw right here if you don't
have the volt meter or you didn't
do it beforehand what i would suggest is power it up with the
lights and turn it down to the lowest voltage
that will still activate the lights the way you
would like them the lower the voltage the longer all
these LEDs are going to last the longer the
components are going to last
so converts it in this case to nine volts DC comes out we have our
negative here we have our positive here
so what happens the positive is split one side as soon
as power goes to the track, one side goes straight to the LEDs,
turns them all on. When power is
interrupted by dirty track, turnouts, crossovers,
then power continues by feeding it from our
capacitor. The diode that we put between the capacitor
and the lights acts as a gate to control
which side the the power is coming from and to keep power
from feeding the wrong way into the
capacitor and causing a short circuit
so that was the the reason for the diode the reason for this
resistor is to slow the charging
of this big 4700 microfarad capacitor without this when you first
turn power on the capacitor is going to suck up all
of the power before the LEDs power up so one
there's going to be a delay before your lights come
on secondly it can cause arcing and sparking
which especially modern uh transformers
and their circuit breakers don't like that and so you could
pop a few circuit breakers
and in severe cases you could actually burn out our uh our
buck converter don't want to do that so that's what
this is for this is for protection it slows
down the feeding of the capacitor and so that's how it works
when power is on it goes straight
from the track when power is interrupted it comes from the capacitor
and everything is all evened
out through the circuit now i did try to paint
these wires a little bit to make them a little less
conspicuous. I don't know how much it's worked.
One thing that in putting it back together I found
that I had not considered was I forgot about these platforms
and so I had to cut off about half an
inch off of either side of the interior.
I have fixed that in the file so if you're downloading
the interior from Thingiverse it will
be the shorter version that will clear these so you
won't have to cut them off like i did
so there it is let's put it back together and let's show
you what it does okay so here's what's happened here's what happens
with a traditional lighted
caboose you see as we go the lights tend to flicker
and yeah i'm not a big fan of that
so put this one on now give it a second
to be in a good spot now not only can we see our flashing
markers here at the end whoops well
that is dirty track there we go okay so you get the lighting
effects here we've got the interior lighting
and now that the capacitor is charged it stays
lit let me change the angle a bit so you can see
the interior lights stay constant no flickering
unless except when i turn it
to where it's completely off off the rails there we go and
we'll put the two of them together you can compare
on the same dirty track so on clean track it would
be an even better effect and that i don't have
to stop it in just the right spot so there we
have it you can protect your train with lighted markers
our flashing beacon nice even interior
lights an optional interior decoration if you would like
but this takes a caboose that as i
I said, when I purchased this, the platforms were broken,
this was missing, had no interior
lighting, had no windows, and now,
with a little bit of TLC, it's the best caboose in
my fleet.
And so there it is, a fun little project,
took me a couple of evenings to put together,
spent more time waiting for Amazon, actually,
than putting the whole thing together.
I don't know if I would do the interior next time,
I don't know if the added effect of
having something behind the windows is worth
the trouble of trying to hide all the wires and I
wasn't all that successful at doing that anyway.
But if you are interested in doing the interior
it is a free download at Thingiverse.
You can find the link in the video comments and if you
would like to give the project a try
of course you could follow along with the video. All of
the parts are listed in the video description
or if you want something handier at your workbench
besides your phone.
I do have a handy PDF document available for download.
Again, you can find the
link to this in the video description.
But in addition to steps for following along, step-by-step
instructions, photos of all the components,
and even a handy troubleshooting guide at the back
in case you set yours up and it doesn't work right,
you can find out answers to common problems
without having to go online and ask.
For example, if you use a 22k ohm resistor instead of a 22 ohm
resistor, it's a common problem, your setup won't work.
Matter of fact, it's such a common problem
that my package from the manufacturer was mislabeled.
I had a little panic for a moment
when the package said 22k ohm resistors,
but they were verified as 22 ohm resistors. They just put
the wrong sticker on the back.
So as always I hope you enjoyed the project and if you did please
like, subscribe, share with your friends,
tell your friends, and tell your neighbors. As always keep
your trains running, keep your rear end protected,
and we'll catch you next time with more toy train
tips and tricks.