I Cut & Polish Ethiopian Opal From Start To Finish.
6 Video Views·Nov 8, 2026
Join me as I take an Ethiopian opal from the rough, carving and polishing it from start to finish. The opal came from the great @PulitzerOpal and I used the Gemfish torch from @blackopaldirect during the process.
Watch the opal transform, see how the torch performs, and find out how the finished stone turns out. What do you think of the final result? Let me know in the comments!
Timestamps
00:00 Rough Ethiopian opal @PulitzerOpal
00:35 @blackopaldirect Gemfish torch
03:44 Carve and polish Ethiopian opal
08:28 Final stone and drying process
11:51 Drying stages
14:00 Thanks channel members
AI Generated·May contain errors
Hello and welcome back to the channel.
Today we are going to carve this from start to finish.
This is a Willow Opal.
In fact if you recognize this handwriting that is from the great
Pulitzer Opal. This is one of those stones
that he sent me quite a long time ago and I've been
spacing them out. This is the last one in this Ziploc bag.
So I'm very keen to get this one
done and then we can have a look at all of them together.
This one has been left last because you
As you can see, there are a few sand pockets
that are going in pretty deep.
And actually it's moments like this that make me pinch myself
because I never thought I'd say this.
This opal is from Pulitzer Opal
and then this is the pen light from Black Opal Direct.
Justin sent this one through to me.
So not only have I had an opal sent to me
by Pulitzer all the way over in the US,
I've also got the torch from Justin over at Black Opal Direct.
Two channels that I watched
for years before I even picked up my first opal.
Now what I'm going to do is I'm just going to use this to show.
That pocket there is not so bad, what I'm worried about is over here.
See how if I shine it in here on this side of the colour bar,
you don't see that side there
start glowing, which means that sand is probably all the way through,
meaning this stone is probably going to split into two.
I'll still have one nice big stone over here,
this one over here is going to fracture
and it's actually got a lot of sand in it,
which I might be able to get out but it might
also destabilise the stone and crumble a bit.
Just because it is an Ethiopian opal.
Unlucky but honestly it is fairly clean except for this
sandbar kind of cutting this into two distinct stones.
Unfortunate but expected hence why I
left this so late. Anyway like any other willow opal
of its kind this is going to be
Hydrophane and it's going to suck in all
the water as soon as I chuck it in.
I don't want that to enable any cracks to propagate
so I am going to try to pick away a lot of this
dry. I might even do a little bit of carving while it's dry.
I've actually now got an extraction
system that would allow me to do it much safer
than I normally would. In fact I'm going to be
a little bit cheeky here
and see if I can just get this to snap using my fingers. Oh super easy.
Look at that, and that is why we use a torch.
That is going to make life so much easier.
In fact we don't even have to do both parts
right now. We could always save this little one for later,
but as you can see that is what happens.
And without that torch I wouldn't have known for sure,
but because of the torch I was very
confident that there was sand splitting these two stones in half.
So don't you just love it
when a plan comes together.
Nothing feels better when you're starting out.
Then that moment in time
when you can start predicting what the rough is actually doing.
Of course having fancy torches
and stuff really helps that but even when you don't have that kind
of equipment you do get a feel for it you do get some good reads
and all of a sudden you can pick
stuff like this without even thinking.
In fact now that we have access all around here let's have a
look. Yeah so this one still has some quite deep sand especially
this sand over here on this side.
This stone will be a bit of a nightmare
and we won't end up with too much at the very end,
so we'll set him aside. This one here though, good chunk.
It's almost like a shard, it's a good spear,
almost ice cream cone shaped.
Let me just get picking away because even though my fingers
can get rid of most of it,
you can see some of it is still dug in there. Let me go get my pick,
we'll just pick at it a little bit
and then we'll spin up and we'll cut and polish.
So my favorite is still to use a flat-headed wood screw.
Nice pointy tip on it. You can
blunten the actual threads if you really want
and they're not super sharp they're not cutting
but I like having a nice solid grip.
my fingers off or anything but it works
super well great purchase you can get big chunks off
as you can see here it works really well
you can absolutely blitz through 99% of that outer crust
and if it comes off in big clumps it's
so much better but then i'm getting
the torch out again and just having a
look i just want to make sure everything is very surface level
I don't want any surprises of deep sand going
in because the water is going to soak in there
and potentially swell and split
so just got to make sure everything's on the surface.
Once that's all done we're going across sintered diamond burr time,
semi-wet I call it, so I dip the burr into the water.
I don't actually dip the stone into the
water I'm just wetting that little bit of sand on the surface just
so that doesn't kick up
dust everywhere. Keeps everything nice and clean,
keeps your lungs nice and clear.
Should always be wearing a mask and glasses anyway.
But you know what, keeping everything
under control is the best way to go.
You can see there it starts getting a bit dry,
just dip the burr again and keep drilling.
We're going to do this and we're really just going
to focus on removing any of these
little rocks, these little pebbles kind of hide amongst the sand
and of course getting rid of the
sand itself. We're not going to worry too much about chipping,
that will be removed later on
with the 600 grit and I typically don't go all
the way to something like an 80 grit for Ethiopian
opal, you can just get a little bit too much chipping.
I like to keep the impact fairly light.
and be pretty gentle with this stuff.
Now when we're carving opal a lot of the time we're doing
it and dry checking everything in between.
You don't want to dry everything out too much.
It's really hard to see issues while the stone's wet.
But even with Ethiopian opal,
you can just give it a quick little wipe over and just dry that
external surface. There's no way you should ever leave it
at this stage, but a temporary surface
dry can really help show you any kind of little chips
or fractures or any inclusions in the
surface. So just do it every now and then,
grind it all back, eventually you'll be able to get to your
high grit sintered diamond, so 600 grit,
and here we're just going to remove
Absolutely everything, just wipe across the surface,
dry it off, have a look,
make sure all the little chips and everything are gone,
then of course you do a dry surface
check at the end and it should look a very consistent,
very cloudy, foggy kind of surface.
Again never just put this down on your desk and leave it,
this is only for a few seconds
and then you want to dunk that back in the water
and start moving on to the next one
or pause there and get yourself some food.
But don't leave it out on the bench to dry.
It most likely will start cracking.
So in this case we're going to go with the resin diamond burrs.
I jumped all the way to 800. I like to jump to the 800 with Ethiopian.
And here I'm just going to show you
in real time how quick it is to go from that initial
faceted surface to something much smoother. There you go. It's already
pretty smooth and I didn't cut anything out there.
That's the main reason I skip over
a lot of those lower grits.
And then we're going to move over to the 1500.
We're just going to...
Prep the entire surface
for the final polishing just hit absolutely everything do some dry
checks if you want but really you want to make sure
this step is spot on otherwise you're going
to end up with a really strange looking surface
at the end where you'll have high parts that are
shiny and then low parts that are the opposite.
And then my favorite part cerium oxide polishing
It never gets old.
At this point once you start getting a little bit shiny
the stone is going to be like handling oil,
it's going to feel so slippery.
The more polished you get the slipperier it gets and once you've
got a really weird shaped stone like
this one it becomes an absolute nightmare to hold on to
but you get better at it and you can get a good grip.
Doping would be so much easier
but unfortunately on a lot of these freeform carvings you're
just gripping on for dear life
and you can do this for a really long time. The key is to
Make sure that you don't feel the stone getting hot.
Opal doesn't like getting hot. Ethiopian Opal
really doesn't like getting hot.
And these felt burrs, they get a really good grip. So you do
want to make sure that the heat is very minimal.
You'll actually feel it heat up and if you ever
put the burr up against your finger,
you'll know exactly how quickly you can get a local hot spot.
So that's the only thing to really be careful of.
Other than that, just chill out, have fun, and just polish away.
The end result is definitely
worth it, so let's have a look at that now.
Alright ladies and gentlemen, that is the end
of that one. I've literally just changed the water,
so gotten rid of the cerium oxide bath,
and given everything a wash, and as you can see,
currently it is still underwater. I did give it
a good dry, but I've just chucked it underwater again,
because I want to show you these steps
Steps from here, you can see this side's got a nice little bit of...
Honeycomb on it. I didn't actually see that originally.
Then you just got some broad flash.
Very typical of a side-on shot of the honeycomb. At the top
there should be a little bit of honeycomb as well
because it is the opposing side, but it's a little bit hard to see.
Of course when this stone dries we'll get
a lot more of this colour and pattern back.
Thankfully it restores itself back to normal
and that's what we're going to do now. So
now that it's all finished, out of the water.
We say goodbye to the water, don't need that anymore.
Can have a quick look of it now that it's out of the tub.
Of course I give it a good wash because
I push pretty hard and for a pretty long time with the cerium oxide.
Sometimes you get little
bits stuck here and there
but because this is such a rounded stone with no pits or anything
You don't get anything trapped in there,
you can see it is super crystal as typical of Ethiopian
Wello Opal but you can see,
actually we've got that other half of the Opal, you can see
how much of a difference it makes
while it's still wet. So this is what it'll
end up going back to,
it'll go to a bit of a crystal still but more off-white.
It'll come back to that whitish body tone,
a little bit more crystal because
this one's getting blocked,
a lot of the light is getting captured by that sand,
so it'll become an opaque crystal white opal.
Really cool, but to get there, what you're going to want to do,
some tissue, give it a dry, give it a real good dry.
You can see here, beautiful shine,
see if I can get that honeycomb to play.
Doesn't do great things with the white background
and then what we're going to do is we're going to
transfer it into a bag with desiccant.
Now normally I would actually transfer it into a sealed bag
without the desiccant, just with the tissue in it first,
but I'm very confident in the stability of
this stuff so I'm going to go straight to the desiccant.
You can see the beads are green slash
Blackish.
There's a sneaky little Ethiopian opal in there.
Those beads are actually quite old
and so I do need to replace them with some fresh ones.
They can be re-dried they'll go back orange
so I like to use the colour indicating stuff
because you just know when you've got to swap
it out. If you get the non-colour indicating stuff you've kind
of got to guess. But all that's going
to happen is in this sealed bag after I change out all
the little beads I'll be putting him
in there with the other ones that are in there.
They don't need to be in there but I've got
But I've got nowhere else to put them right now.
We're going to seal it back up
and we are going to see this transform itself back into its
uncut half. So it's going to look more like this.
Also you can look at the ones that are
in there again. It will actually be quite similar to this one but
quite a bit bigger and a little bit more blue
which is a bit of one of the rarer colors.
You'll see a lot of green, you'll see a lot of red, you won't often see
a lot of blue. Whereas this one here you'll see that there is
of course a lot of green but there's
also a little bit of blue in there.
Some of the warmer colors come through with a bit of yellow but
all in all it's going to be a very green
and blue stone. I'll get this one drying
and if it looks different enough I'll include a little snippet as I'm
editing away on the video. But we've got the other half so I'm not
too worried about, not too worried about that it's just gonna
It's going to become a bit more like this.
The colours will get crispier.
The opal will get a little bit wider, less transparent.
All in all pretty good.
Shape is a little bit weird. I was constantly tempted to cut this off
because it would have helped me grip the stone a little bit better.
I thought for a while it was going
to look a bit like a submarine and then I
thought it looked a little bit like
the flute from Zelda, if you know your
video game references. But yeah, another opal done.
Good fun. I highly recommend beginners check out
a little bit of Ethiopian Opal.
Some would say it gives you the bad habits
because it grinds away so soft, so easy,
so you can fly through your stages without
actually causing yourself too much trouble.
With harder stones you need to be careful when you go up the grits.
If you miss some scratches they can
be really hard to get out at higher grits.
Whereas Ethiopian Opal, just like this one,
I ended up skipping the 200 and 400 resins,
Just jumping straight through to 800.
Because the opal just melts away even at the 800 mark,
so much more forgiving. You can also polish
it with cerium oxide, aluminium oxide, diamond paste, it doesn't care.
All the above will work
as long as you've got the high enough grit,
diamond paste and aluminium oxide.
Cerium is by far the best though. I find it gets the best final polish.
It responds super well, Ethiopian Opal,
to being polished with Cerium Oxide.
And of course it's just a one-step process.
You don't need to go up 10 different grits of Diamond
Paste to get there. You can just use the one Cerium Oxide
and you suddenly get this glossy
look from what looked like a very rough surface of a 1500 grit burr.
That final step transformation
is super cool. And even in the time we've
been talking, I can already tell
That this opal is drying out because some
of these desiccant beads are still kicking along pretty strong.
But I'll call it here.
I hope your carving is going just as well.
That was a nice easy one for me.
Let me swap out some of this old used desiccant for some fresh stuff.
And I've got a lot of other stones to
work on so I better keep on moving.
Stay safe, have fun, good luck with your carving
and I'll see you in the next one.

