In this video I fully automate the raising and lowering of my FLEXIMOUNTS GL1 overhead lift storage units! I add a motor and custom couplings to a PLC that I integrate into my shop SCADA system to create a fully remote controllable, autonomous, overhead workshop lift system!
These are my overhead workshop lifts.
They can each lift up to 350 pounds,
descend up to six feet,
and are fully controlled by my workshop automation system.
And today, I'm gonna show you how I built them.
My workshop is my sanctuary.
Home gym, music studio, wood shop, filming studio,
electronics and computer projects, 3D printing, and more.
But having so many hobbies
means I am completely out of space.
But I'm fortunate to have pretty high ceilings in my garage,
so there's a lot of unused volume over my head.
So I decided I wanted to put in overhead storage.
This is Lemaster Tech.
My audience is automation nation.
We can't just slide some bins
into a stationary overhead rack and call it a day.
So I set out to create a remote controllable,
fully automatic overhead storage system.
I started by finding a popular overhead storage system
from a company called Fleximounts,
which was their GL1 product,
which is an overhead platform
designed to be raised and lowered manually.
It's a four foot by four foot square platform,
and it says it's rated for up to 350 pounds.
And it can be raised or lowered about six feet.
I figured if a person manually turning a crankshaft
or using a power drill can raise or lower this system,
then surely I could create an automated solution for that.
A huge shout out to Fleximounts
because I reached out to them
to see if they'd be interested
in providing the hardware for this video,
and they graciously agreed to sponsor the video.
In addition to this GL1 overhead platform,
they have a ton of great garage and workshop,
wall storage, cabinet, roller,
overhead storage solutions on their website.
So huge thanks to Fleximounts for sponsoring this video,
and be sure to check out all their great products
at the links in the description below.
Now the physical install of these systems
is pretty straightforward.
You need to make absolutely certain
that you are mounting these into studs,
otherwise it's not going to be able to hold any weight.
Included template will work with joists and studs
spaced at 12, 16, or 24 inch spacing.
You basically just need to install four brackets in total.
Two are going to hold the axle
that actually spins while it's rotating,
and two are going to hold pulleys,
which is how you support the four corners of the platform.
The platform itself is wire mesh with a solid metal frame,
and it connects via these cable points to all four corners.
When you first install it, it'll be hanging low,
so you just reel it all the way up.
I found with a little bit of weight on it,
it kind of did like a self-leveling thing
and just came to a really good even spot.
Just from running it all the way up
and all the way down once.
It says two-person install required on the box,
but mama didn't raise a little bit.
All in all, these were pretty easy to install,
and even without any special automation yet,
this was a huge improvement to my storage woes.
Now that we have the platforms installed,
it was time to cook up some Lemaster Tech custom automation,
because I do not want to be standing there
holding a crankshaft or running a power drill
anytime I want to raise or lower these.
And the gearbox that comes on the axle
is actually already doing a huge amount
of torque reduction for you.
I wanted to challenge myself to design the automation
for an incredibly affordable price point as well.
I knew I wouldn't need some insanely strong motor.
So for not even 30 bucks,
I was able to get this 40 RPM motor off Amazon,
which has a worm gear off the motor
to translate its motion 90 degrees.
It also has a self-locking feature, which is really nice,
so I know this thing is not going to back off
and start creeping down when it's being held at height.
To mount that motor to the loop
coming off the gearbox on the axle,
I wanted something that would give me
a little bit of flexibility
in the way I mounted this system.
So I decided to get these U-bolts
and design a custom coupler
to go from a flanged connector on the motor
to the U-bolts that'll hook through the loop on the axle.
My 3D printer is definitely able
to make a part strong enough to hold this together,
even though it would probably be better
to have a metal component.
And if I get better CNC capabilities at home,
I'll probably start making
these sorts of components out of metal.
To afford that, I'd need the channel to get a bit bigger.
So hey, if you're enjoying the video,
consider subscribing and leave a like on it.
I'm going to mount this axle to the U-bolt,
the U-bolt to my coupling plate,
my coupling plate to my motor flange,
my motor flange to my motor,
and my motor to its bracket.
That bracket is going to mount to a 2x4,
and that 2x4 is going to mount into another 2x4
connected to the studs in the ceiling.
And before connecting it to a smart controller
to tie it into my automation system,
I'm just going to use a 24-volt power supply
and a simple rocker switch
to test it going up and down
and make sure that my mechanical linkages start working.
It is really encouraging.
My little motor and coupling system
have no problem raising and lowering this,
even with some substantial weight on there.
So now let's move on to automated control.
To get this simple motor to spin,
all we need to do is connect 24 volts to one wire
and zero volts to the other.
And as long as your motor supports bidirectional movement,
you can just flip those two wires to reverse the direction.
As I showed in great detail in my video
on how to control linear actuators
and in a few shorts on the channel,
we can use two output signals from any microcontroller
and a series of relays to use an enable
and a direction signal off of our controller
and flip-flop the state of these wires,
as well as have the ability to kill it completely
so it's not moving.
Using these relays,
two outputs from any controller system I choose
need just a few milliamps
to pull in the coils on these relays.
So we can provide dedicated power to spin the motors
on the downstream side of these relays,
and the enable signal will be getting used
to control if the motors have any power or not.
So it'll kill the power feed
to the wires going to the motor.
The direction signal will flip-flop the two relays
that we land our red and black wires from the motor on.
And now this exact setup would work fine with an Arduino
or an ESP32 or any other microcontroller,
but you would need 3.3 volt or five volt relay coils.
Because I wanna tie this into my garage automation system,
it makes more sense for me to use a PLC.
So I'm using 24 volt coil relays and an Arduino Opto,
which is a pretty cool edge device PLC
that lets me integrate it to my SCADA
or supervisory controls platform
using a software called Ignition
and a comms protocol called Modbus.
So I throw a dedicated 120 VAC to 24 volt DC power supply,
my Arduino Opto PLC,
and my relays on this little strip of DIN rail,
which is this universal mounting platform.
That's all I need for the controls hardware.
And I just need to power it up
and run an ethernet cable from that PLC back to my computer.
I write up a little bit of code
so that I can recalibrate the height of this thing,
command it up, command it down,
change the max and min height settings,
and view the status of how it's running
and where it is in space
so that I can create a cool visual HMI
or human machine interface screen.
All PLCs use special PLC programming languages
like ladder diagram or structured text,
but the Arduino Opto also supports C++
like all other Arduino microcontrollers.
So you can really program this thing any way you want.
And once I get my HMI built out on ignition,
test that the comms back and forth
between my PLC and my screens are working,
all I really need to do is load this thing up,
calibrate it, and take it for a spin.
And it works so well.
And now I can put 700 pounds on these things combined,
reclaimed roughly 100 cubic feet of storage in my workshop.
I can control this thing remotely
through my workshop automation system.
Honestly, this whole project was so much fun.
It has me scheming about all the other things
I could tie into this control system.
I hope you found this fun and useful.
Let me know in the comments
what you think the workshop needs to see next.
Thank you again to Fleximounts for sponsoring this video.
You can find links to all the hardware I needed
to make this project possible in the description as well.
Thank you so much for watching.
Don't forget to leave a like on the video
and subscribe to Lomaster Tech.
See you next time.
Thanks, bye.