How To Make Captain America's Shield From The Falcon and The Winter Soldier

Shielded Dynasty Network
2 followers
Mar 17, 2026
Hey guys, welcome to my channel. Today we're going to be making Captain America's shield from the Falcon and the Winter Soldier.
This one.
Yeah, let's just get straight into that.
Okay, so, like, fat disclaimer, this video is going to be really long, so I'll put timestamps in the description, but
you're going to want to get a foam board, that's what I'm using to make the shield,
and I'm just measuring the, I'm measuring out how big I want it to be, and, like, the size that I want the circles to be and everything,
and then I'm just writing that down. I'll link in the description how I, or the article that I used to figure out the circle sizes
for a 25 inch shield. So yeah, then I'm just drawing that on, putting a screw in there and having a piece of EVA foam
to draw it on with. That's a good technique to use.
So now I just start cutting out those circles with an exacto knife, and I'm just using a self-healing mat on the ground,
and then I start taping them together.
Yeah, then I just take it off so I can cut out all the rest, and then I'm just piling them up there in,
just, like, on the ground there, and now I'm curving them, just, like, folding them and then just taping them
so that they get that curved domed shape that you're going to want for the Captain America shield.
For this middle circle, what I'm doing right here is I'm just cutting it smaller to try and fit it in.
This isn't actually how I got the circle to fit in, because the way that I did it, I actually got it to be domed.
I'll show you guys later in the video, but now I'm just bending all of that and taping that all together.
And I put the middle seam where it curves a little bad, so here you can see I'm fixing it so that that middle seam,
where each little circle ends up, is, like, opposite.
And then I'm just gluing that, taping on the outside, and then just gluing on the inside.
And then I grabbed the homemade compass I made just to draw some of the detailed lines in there,
and then I'll come back to those later.
But here you can see I'm just, I kind of burned my hot glue stick, so I'm taking those out.
But now what I did was I got the foam board, I cut out the circle, and it was a little bit bigger than what fit in there.
And so I just took off one of the papers, since it's paper, and then some foam, and then a paper on top.
So I took off the bottom paper, and then I just stuck it in there and put tape so it would stay down and it actually domed itself.
And yeah, that's how I got that to stick there.
And then I'm figuring out what I'm going to do to cover the part that I took the paper off of.
I end up just sticking a piece of BVA foam in there, as you can see here.
I'm gluing that on, and I'm just cutting off the excess, and then I take the tape off here.
It was a bad idea because it wasn't actually stuck down, and I have to put it right back in there, as you can see there.
And then I just hot glue that middle circle right in there to make sure that it stays.
And yeah, you're just going to want to use some really strong glue, and just be careful with that.
Wipe off the glue so it's kind of smooth on the inside.
But yeah, I'm just fixing that EVA foam to there to make sure that it just stays.
So now what you're going to want to do is get a screw and a piece of EVA foam, and you're just going to want to cut that out and measure that.
Because I'm going to draw the line that goes on the red.
If you've seen the actual shield, you know what I'm talking about.
But now I start to cut out those detail lines that I made, the silver one and the red one now.
I know they're not colored, so it's kind of hard to see, but now I cover that all in Elmer's glue to protect that,
so that I can actually paint it and put masking tape off, and the paper won't rip up, if you know what I mean.
But yeah, I'm just covering that.
Just get a really big paintbrush so that it'll be a lot faster.
And I'm breaking out my Dremel that I bought a couple days ago.
I'm just sanding down the whole thing.
Just some of the spots were a little rough and stuff, so I'm just sanding that smooth, polishing it all and stuff.
And then that dome shape, some of it was kind of coming out like the middle circle of the dome.
And so I'm just sanding that off, and I'm sanding off some of the hot glue and some stuff on the top.
But yeah, I'll link the Dremel in the description for you guys if you'd like to buy it yourself.
But I just keep sanding that whole thing down on the top circle and everything.
Just really get that sanded down good, because you want it to look smooth.
You want it to look smooth, you know.
And yeah, that's pretty much what I'm doing here.
So now I start to put away that Dremel, and now I'm adding a second coat of that Elmer's glue.
Just to really make sure that the paint and the masking tape does not mess up that foam core.
And it really, it honestly works. You could use Mod Podge or glue.
Yeah, I'll link some in the description too.
Now I'm just coating that EVA foam piece on the bottom of the shield, the back I guess you could call it, with glue.
Just because it will not paint if you don't coat it with a little paint, but it'll absorb a bunch of the paint.
It really doesn't work.
And then I'm trying to give the whole back a coat of glue, but there really wasn't enough.
Make sure you buy enough glue to do this, and at least give it two coats.
I gave it like half of one because I didn't have enough glue, but yeah.
That's alright.
And yeah, I just keep trying to get that glue out and just adding more glue.
You're going to want to add a lot to that EVA foam because it absorbs literally everything.
And you're going to want to be careful because it does leave brush strokes on that EVA foam.
I learned the hard way that it does that.
But I just continue to coat that shield, the foam board, with more Elmer's glue.
Yeah, just about enough as my bottle has.
And now I've painted the silver on the front, and now I'm just masking it off so I can go ahead and paint that red.
And I don't want to put masking tape all over the whole thing, so I put it right on the edges, and then I put paper in the middle, as you can see here.
And that's just because if you put a bunch of masking tape, it could actually rip up your foam board, but it's also a waste of tape.
Because you're going to need a lot of it.
So I just like to use paper, and I'm just using scrap paper or just a bunch of paper that I found.
But yeah, you just rip that up and put that in the shape of it.
And yeah, I'm going to go paint it.
Okay, I've painted it now.
I've painted those red sections.
Now it's my favorite part, removing the masking tape.
But yeah, now you're just going to want to get your X-Acto knife and rescore in those detail lines.
Because after two coats of Elmer's glue and a coat of paint, they'll be pretty closed up.
You're just going to want to reopen those with your X-Acto knife like I'm doing here.
I'll link an X-Acto knife in the description for you guys if you don't have one, or if you want one, or whatever.
I'll link that for you guys.
And I'm just scoring, rescoring in that red detail line.
If you've seen the actual shield, like in the show Falcon and the Winter Soldier, you'll know that there's actually two detail lines.
And now I'm just designing the little band that goes on the bottom.
It's just a band that goes through the bottom.
You'll see once I flip the shield over and actually glue some of it on.
And that's a detail that's been on the shield for all the movies.
You're just going to need like four of those.
And yeah, you just trace the bottom of the shield and then just guesstimate how much you're going to need.
I felt like maybe two centimeters or like one, one centimeter probably, I don't know.
I didn't really measure it again, just guesstimate that.
I cut out a paper template for the piece that holds the strap, like the little metal piece that holds the strap.
So I cut that out.
And the way that I did that is I just like put a paper on the strap bracer thing.
And then I just got the corner and then I just cut out two rectangle holes and then folded one side up.
And I then start cutting it out of the one millimeter EVA foam that I used for everything else.
But it was a little too thin.
So I tried to cut it out of foam core, but that didn't work because it doesn't fold very well.
So then came back to the EVA foam.
And what I did was I cut out three of them and glued them together.
And then the piece that folds up, that holds the strap, I cut that one off and then I hot glued it on.
I hot glued those on after, so yeah.
I keep trying to cut out the foam core, but it doesn't work.
It just starts falling apart because like it just doesn't fold very well.
So that's the issue that I had with that, but yeah.
So I then go right back to the EVA foam and I decided that I'm just going to do three layers.
If you have three millimeter EVA foam, this would probably end up working like a lot better.
But like I said before, I just did the three layers and hot glued it together.
And it honestly worked out quite fine.
And then I just cut off the piece that holds the actual strap.
And then I glued those three together and the other three that just sit there and hold the other decorative piece.
And I just glued those together, so yeah.
And then start cutting it out.
And you're going to need like four of these.
So I'm using an X-Acto knife to cut it out.
And make sure that your blade is quite sharp because foam really dulls your blades up.
And then I can't emphasize how much you need to put something under what you're cutting
so you don't mess up your surface because my desk is quite destroyed from all these things that I've made over the years.
And it's, yeah, just make sure you put something under there.
And then keep cutting and cutting and cutting.
And do listen to music or watch a movie or video or something while doing this
because it gets quite tiring and annoying at some times, but it is extremely worth it.
It does pay off.
And then start hot gluing the straps inside of the bracer or the things that hold them.
What I do is I just put it inside of the foam, the EVA foam piece,
and then I just wrap it around and hot glue the bottom.
Also, if you're using belts like I am, they generally have a brown piece on each side.
So what you're going to want to do to save, or to use, to save leather
is just rip that in half and then use the top and the bottom piece.
And it also makes it thinner, so yeah.
And then start cutting out the piece that holds, the bottom piece that holds the leather strap,
which isn't actually a strap, it's just, it goes on the sides.
You probably know what I'm talking about, and if you don't, well,
just look at a picture of the back of the shield and you know what I'm talking about.
But pretty much it's just a rectangle, and then there's just a rectangle cut out in the middle
for the strap piece to go inside.
So yeah, that's all it is.
And then start cutting and gluing and cutting and gluing,
and you're going to need about four of these, I believe.
So yeah, four of these.
And it doesn't really matter the color of them, even like,
it could be like a red sandwich to a blue, it really doesn't matter,
because they're all going to be painted silver.
And then start gluing the straps onto the shield.
Before they're painted, you're not going to want to do that.
What you're going to want to do is just paint them first, and then put them together.
Yeah, before you even put them together, you want to paint them.
You want to paint them to cut a super straight line.
That's what I did.
I cut out a paper template for the strap bracket,
and the reason I'm doing this again is because the templates that I cut for the things that hold the straps,
one's bigger than the other one, so the bigger one I actually had to cut out another piece.
So yeah.
And it's quite straightforward.
It is literally the exact same thing.
You're just cutting out a bigger one, depending on the size of the strap bracket thing.
I seriously have no idea what to call that.
And then start cutting this new template piece out of EVA foam,
and you're going to need four, no no no, you're going to need two of these,
and then, so pretty much six of them because each has to be three layers thick.
You're probably not going to make this mistake, but if you do, this is how you fix it.
And then start hot gluing the new strap brackets together,
and you're probably not going to make this mistake again like I said before, but if you do,
this is how you fix it, and again, I'm not perfect, but the shields turned out really good, so yeah.
And then start cutting out the rectangle strap bit piece that holds the leather detail.
And again, it's the same straightforward process,
I just had to make it a little bit bigger, and then you're just hot gluing three layers together.
And yeah.
Again, I'm just cutting these out, quite straightforward process.
Something that you can actually do with EVA foam pieces like this
is you could spray them with a couple coats of Plasti Dip,
and then that'll seal them up, and then it'll make the painting process a lot better.
And Plasti Dip is just a rubber spray that really seals up your foam and makes it look really nice.
I then start gluing the belt strap pieces to the EVA foam bracer bit things,
I'll call them I guess bracer bits.
And then I grab the whole assembly and I start to glue it onto the shield,
just hot gluing it and making sure that everything is in the right place,
and that it all fits right together, and yeah.
And now this is quite straightforward, just make sure you've bought enough belts to do the project.
I just hit up the Goodwill and then just got like a ton of belts there.
But just make sure that your belt is the right brown and it's flexible enough,
and it'll work for your thing, you know what I mean?
So for the star, what I decided to do was just pretty much use that compass that I made,
which is just a screw on some EVA foam,
and then I just made that, or I measured out the circle, the center circle on the shield,
and then I just traced that onto some paper, and what I did is I found a star on mine,
I'll also link that in the description for you guys,
and then I'm just tracing that onto the paper and then like cutting it out and adding a little bit.
I'm just like adding a little bit so that it totally fits on that circle on each edge,
and now I'm just tracing it on to, or I'm finding the spot that I need it to be,
like where the point needs to be, so when I wear the shield on my arm,
the point is like facing up, if you know what I mean.
I'm just tracing that on, just tape it on with some masking tape and then fill in those lines.
And yeah, now I'm just tracing out some of the details,
I'll leave that in the description, I'll show a picture of those details so you can trace them on as well.
I'm using a mechanical pencil, it works a lot better than a number 2 pencil since it's like pretty much always sharp,
but yeah, and then you can erase on the foam board as well,
and now I'm just scoring in those lines with an exacto knife,
and scoring means that you cut it in, you cut in the details, but not all the way through,
so in the case of a foam board, you cut through the top layer of paper and the middle layer of foam,
but leave the bottom layer of paper there, and so you cut through those,
and then it's just scoring and it looks really, really nice.
But yeah, that's what I'm doing, and I'm just going through every single spot,
I'm being really precise and really slow.
But yeah, now I'm just adding, I'm masking off that star,
and yeah, so I can paint the blue onto that center circle,
and I'm just masking off the whole shield except for that center circle,
just so I can make sure that I get none of it blue,
and the fact that I covered it in Elmer's glue,
you can literally put as much masking tape as you want, and it won't damage the foam board,
but it did actually rip some of the paint off,
and now I'm just adding in the little rectangles,
at every single point of the star on the silver little band there,
there's just little rectangles, and I'm just scoring those in,
and yeah, I'm just scoring those in,
and then here I'm just masking off everything else,
so I can go ahead and repaint that red that got chipped off by the masking tape,
and you can avoid this just by getting some masking tape that's not too sticky,
but make sure that it still will protect whatever you're painting on, you know what I mean?
So I unpainted that, then I removed the masking tape,
and yeah, now what I'm doing is I've just got some black paint and a paper towel,
and I'm just putting it into those little rectangles,
and then I'm just wiping it off really fast so that it only gets in the rectangles,
and that's about the only spot that it goes, so it doesn't get anywhere else on the shield,
and I'm just adding that into every single rectangle,
and yeah, then you can just see I'm just wiping it off,
it'd be a lot better if I had a smaller paintbrush,
you guys should definitely use a smaller paintbrush for this,
but yeah, now I'm just putting that black paint into the star,
and all those little scored details and crevices and stuff,
and I'm just then wiping it off, and I'm putting it into the silver band,
the silver scored line, and then just wiping that off.
So I just finished the shield, and this is what it ended up looking like,
and I'm honestly quite happy with the blue and the star, the weathering and stuff,
I did mess it up a little bit though when I was putting the black into the star,
it kind of got into these divots because it wasn't well filled and sanded,
but here's the back, with those 3 decorated pieces there,
and then, yeah, I'm honestly really really happy how it came out,
and then the edges, I painted them red and everything.
So yeah, that's the shield, if you liked the video or found it informative in any way,
don't forget to leave a like down below,
and subscribe if you like my content and would like to see more,
comment down below anything that you'd like to see me make next,
I post videos every single Friday,
come back next week to see the video on the belt for the Captain America,
Sam Wilson Captain America cosplay.
