How to build your own workbench - Step by Step Guide

The BeefMaster
118 followers
55 Video Views·Dec 11, 2022
In this video I'm going to replace this old safety hazard workbench
with a new custom built one and I'm going to show you step by step on how to do it
and I'll have the plans linked below. To get started I'm going to clean out a work area
then get my measurements. I'm going to make my workbench 35 inches tall so it matches the height
of this table saw. The height of the bench is going to be 35 inches minus 5 inches for these
wheels. I'm going to take another one and a half inch off the height to account for the one and a
half inch thickness of the tabletop so that means I'm going to cut all my legs at 28 and a half
inches. I ended up making 10 28 inch cuts. Next I laid out the tabletop so I could get a measurement
of the frame. With the frame laid out I can now start putting everything together. To hold it I
ended up using some Titebond wood glue as well as three inch construction screws. To hold these
4x4s together I ended up using these Spax power lags. You don't have to pre-drill a hole so it
makes it very easy to put in. This is the frame for the top so I'm going to flip it over and put
on the bottom piece. With the bottom frame on I now have an outline shelf for my workbench. It's
really just two rectangle boxes held together by a square middle. The workbench is going to end up
being 4x8 feet but it's very easy to modify a box design like this if you want something smaller.
Next I'm going to use some scrap wood to build supports across the top and bottom. To mount the
supports I'm going to use one of these Kreg pocket jigs to make holes for the screws.
Now here I kind of made a mistake because after I put the support braces up I decided I wanted
shelves on the bottom. So if you want shelves I recommend waiting before you put on the top
support braces otherwise the shelves can't fit inside. It's not a huge deal because you can
temporarily take them off but I'll show you what I mean later. Moving on the next step is to put on
the wheels. For the wheels I use these ever built casters that have a total weight capacity of 350
pounds. These lag screws are very strong and require pre-drilled holes and a ratchet to screw
down. With the wheels on it made it very easy to move around. Next step is to put on the bottom
shelves so I'm going to take its measurements and then cut around the support beams. It was about
here when I realized my mistake so I took off the support beams on the top then put on the shelves
and then screwed them back in. For the two side shelves you can see here I cut around the support
beams and I'm going to do the same thing for the back piece. I have the shelves cut so now I'm going
to use a countersink bit like this to pre-drill the holes so that I can screw them down and
everything will be flush. It's important to pre-drill the holes or use a countersink bit
otherwise the wood can split when you're screwing in so close to the edge. I like using a countersink
bit because the screws sit flush so it will be a lot easier when I slide things on and off the
shelves. Now this next step is kind of optional but I want to run power through this thing so I'm
going to pre-drill holes so I can slide the wire through. With that done it's now time to put on
the tabletop. I was going to make the tabletop out of three quarter inch birch plywood but it was all
out so I ended up using this sand material. Sand plywood is actually a little bit lighter so it's
going to be easier to move the table around. The downside is that it's a little softer so it's
going to be easier to scratch. Early on I decided I wanted my table to have a little cutout where I
could stand or sit. This tabletop is four by eight but if I was making a smaller one I probably
wouldn't have this cutout. Eventually I'll have some plans for a smaller table link below that
you can just download. I plan on putting some heavy items on this table so I'm putting an extra
plywood sheet for support. Having this thickness gives me some versatility if I want to add saw
I'm going to put these one and quarter inch screws underneath the table because I don't want
them to be visible. I'm going to repeat the same process and make a cutout for the notch.
With that my workbench is put together but after using it for a little bit I decided that I wanted
to run some power through it. I'm going to run all the power through this switch so that it can turn
off and on the plugs downstream. To get the power to the switch I found an old black extension cord
that I cut off the end then I spliced the wires to connect to the switch. The hot line connects on
the bottom right and the load on the left side is then carried to the plug. Because I'm on a 20 amp
circuit I'm going to use this yellow 12-2 cable to run the power to the extra plugs downstream.
So again the hot wire goes to the switch then connects to the plug then the load is carried to
the other outlets through this yellow cable. If you don't feel comfortable talk to an electrician
to make sure you're doing everything right. With everything wired I put on some metal face plates
then grabbed a shop vac to test out that everything was working. The idea behind this is that I can
now flip a switch to turn on the vacuum for easy dust collection. And with that we now have a
powered portable workstation. This workbench is a huge improvement from my old workbench that looks
like a cheap robot dog. This new one is much more safe and will help me be more productive.
As I mentioned earlier I'm going to have these plans and other plans linked below.
If this was helpful check out my home playlist for other builds.
Thanks so much for watching and have a great day!
