This U.S. Navy Training Film is about the basic WW2 submarine structure and systems. It is a description of the pressure hulls, tanks and super-structure.
The submarine shown at the end of the film is the USS Tusk (SS-426), a Balao class submarine. She was the only ship of the United States Navy to be named for the tusk. Her keel was laid down on 23 August 1943 and she was launched on 8 July 1945. She is one of the last two operational submarines in the world built during World War 2.
The Balao-class submarines: The Balao-class was a successful design of United States Navy submarine used during World War II, and with 120 units completed, the largest class of submarines in the United States Navy. An improvement on the earlier Gato-class, the Balao-class submarines had slight internal differences. The most significant improvement was the use of thicker, higher yield strength steel in the pressure hull skins and frames, which increased their test depth to 400 feet (120 m).
The basic construction of a submarine consists of the pressure hull,
the tanks which are built around the pressure hull,
and the superstructure. The pressure hull,
which includes the conning tower, is the principal part.
This hull must be watertight and airtight and able to resist the water
pressure when submerged. The hull is circular for maximum strength
and is reinforced by steel frames over its entire length.
Watertight bulkheads with watertight doors subdivide the hull
into separate compartments. These compartments contain
all the machinery, equipment, and furnishings
necessary to operate the submarine. Let's see what each compartment is used
for. Amid ships is the control room. The control
room has the control gear for steering, diving, and operating submerged.
One part is generally used as a radio room.
This space below the control room is called the pump room.
It contains auxiliary machinery. Next to the pump room are spaces for
storing food and other supplies. Above the control room there is usually a
conning tower with the two periscopes and the fire
control equipment. The ship is normally steered from here.
Fore and aft of the control room are the battery spaces.
They contain the main storage batteries which supply electrical power for
operating the ship when submerged. Above the forward battery space are
quarters for officers and for chief petty officers with
accommodations for eating. Above the after battery space are the
This space below the cruise quarters is used as a sonar room.
Aft of the cruise quarters are the two engine rooms.
Each contains two main diesel engines and the generators they drive
together with auxiliary equipment. Aft of the engine room
is the maneuvering room which is the electrical control station for propelling
the ship. Here are the main motors which drive the
propellers. The two remaining compartments at either
end of the hull are the forward and after torpedo rooms.
There are six torpedo tubes forward and four aft.
Each room has a torpedo loading hatch and stowage racks for spare torpedoes
and contains bunks for some of the crew. The escape trunks are also located in
In this way the pressure hull of a submarine is divided into compartments
each of which plays an important part in the operation of the ship.
Fitted around the pressure hull are the tanks.
There are ballast tanks which control the buoyancy of the boat
and fuel tanks. The main ballast tanks are completely flooded when the boat is
submerged. Some of these main ballast tanks are
divided into port and starboard tanks.
This is a cross-section. The tanks have flood ports
open to the sea. The main vent valves control the escape of air when flooding
the tanks. These are emergency vent valves. They are
used in case of damage to the main vents or to prevent accidental flooding.
In order for the submarine to submerge both sets of vents
must be open to flood the tanks. Since the tanks are open to the sea when
submerged the pressure is the same on both sides.
Therefore the outer skin of these and similar tanks
is not made as strong as the pressure hull.
In order to surface air under pressure is admitted to blow the water from the
tanks. High pressure air at first followed by
low pressure air. These two main ballast tanks operate in
the same way except that they are not divided and
have no emergency vents. In addition to the main ballast tanks
there is a group of variable ballast tanks.
These are used to control the trim and buoyancy of the submarine.
They are the forward trim tank, the after trim tank,
two auxiliary tanks, and the forward and after
water-round torpedo tanks. These variable ballast tanks are only partly filled
and the seawater can be pumped from one tank to another
or to sea. There are also three special purpose ballast tanks. The bow buoyancy
tank, the safety tank, and the negative tank.
The bow buoyancy tank is blown to give the boat an up
angle. The safety tank can be blown quickly
to obtain positive buoyancy. The safety tank seen here in cross-section
is fitted with flood valves, main vents, emergency vents, inboard vents,
and high pressure blow valves. When the flood valves are shut
this tank can be used as a standby variable ballast tank.
The negative tank is a small tank located inside
one of the main ballast tanks. It has a flood valve
and an inboard vent. For submerging or for a rapid change of depth this tank
is flooded. As the boat approaches the desired depth
the tank is blown and the flood valve is shut.
This restores neutral buoyancy. The negative and safety tanks as well as
the variable ballast tanks are strongly constructed to withstand
full submergence pressure. The fuel tanks of the submarine are also
fitted around the pressure hull. These tanks contain the fuel oil for the
diesel engines. The fuel tanks and the fuel system will
be discussed later in this film. We have seen the
pressure hull and the tanks which form the outer hull.
Now the addition of the superstructure completes the submarine.
Here is the bridge which is the boat's control station when on the surface.
The superstructure plating streamlines the bridge,
conning tower, and periscope supports. From the deck
hatches lead to various compartments in the pressure hull.
Now let's examine the principal equipment and machinery used to operate
the submarine. The propelling machinery includes the
units which drive the submarine through the water.
Most submarines have four diesel engines which are used when the boat is on the
surface or snorkeling. Each engine drives its own generator.
The generators provide power to the main motors
which in turn drive the propeller shafts. The generators in addition to supplying
power to the main motors also provide power for charging the main
storage batteries. The power is distributed through the
main propulsion control cubicle from where it is sent to motors, to
batteries, or to both simultaneously.
When submerged and not snorkeling, the main storage batteries provide the power
to drive the main motors. These batteries also give power to
various electrical auxiliaries and for ship's lighting. The fuel oil and
compensating system delivers the fuel from the storage tanks
to the engines and replaces the fuel with seawater.
These tanks are used for either fuel or main ballast
and are called fuel ballast tanks. These tanks are called normal fuel oil
tanks. In addition, the system includes an
expansion tank on the port side and a collecting tank to starboard.
We can see how this system works with the help of this diagram.
Each fuel oil tank is connected to the fuel transfer line
which is also connected to the collecting tank.
The top of the expansion tank is connected
through a manifold to the compensating water main.
This main runs inside the boat with branch lines
to the bottom of each fuel tank. The compensating water system
also includes a line which runs from the bottom of the expansion tank
through the manifold to the top side and forward in the superstructure
to a header box. This header box is more commonly called a gooseneck
because of its shape. The gooseneck is located in the Conning Tower fair water
and is open to the sea. The cooling water system of each
engine is connected to the compensating water line.
When the engines are running, they discharge some of their cooling water
into the compensating line and keep the gooseneck filled.
This column of water sets up a head of pressure
in the expansion tank. This pressure is transmitted
through the compensating main to the oil
in the fuel tanks. Since the oil is lighter than the water,
the oil always floats on top. The water replaces the oil taken from the
tank on service. The water pressure forces the oil through
the fuel transfer line to the collecting tank. From the
collecting tank, the fuel oil passes through a purifier
to the clean fuel oil tank from which it is delivered to the engines.
Note that when the submarine is submerged, the gooseneck and compensating
line serve to keep the pressure inside the
tanks the same as the sea pressure outside.
Thus, the fuel tanks are never subjected to stress.
The air supply and exhaust system provides for the diesel engine's
air intake and exhaust and takes care of ventilation of the ship's compartments.
When the submarine is on the surface, air is taken in through the main
induction valve located in the Conning Tower Fairwater.
Starting at the main induction valve, a line runs to the forward engine room
to supply engine air. A line runs to the after engine room
to supply engine air. A branch of this line may go to the
maneuvering room to aid in ventilating this compartment.
Another line from the main induction valve to the forward engine room
is the main source of fresh air to ventilate the entire hull.
The exhaust gases from the engines are discharged through the engine exhaust
piping, the outboard exhaust valves, and through mufflers to the atmosphere.
When the submarine is below the surface, the snorkel system may be used to
provide air supply and exhaust. Air is taken in through the snorkel
induction mast. It passes through a water separator
to the snorkel induction valve and enters the system
just below the main induction valve. The engine exhaust goes through snorkel
exhaust valves to the snorkel exhaust mast.
The induction and exhaust masts are telescopic.
When the snorkel system is in operation, they are raised
so that the head valve atop the induction mast
projects above the surface and the exhaust
is a few feet below the surface. To prevent flooding,
the head valve is electrically controlled so that it shuts
when water passes over it. The exhaust mast
has a diffuser which dispels the exhaust gases,
thereby reducing the telltale wake. Hull ventilation is primarily controlled by
a blower in the forward engine room. It forces air along the main supply line
where it passes through air conditioning units.
Branch lines supply the conditioned air to the compartments.
The forward battery has its own booster blower and cooling coil
which is used to supply air to the compartment and to the forward torpedo
room. Exhaust lines carry the air back from the
compartments to the forward engine room. If the
engines are running, they use this air and it goes overboard
as part of the engine exhaust. Fresh air is supplied to the blower
through the line from the main induction valve.
When the submarine is submerged, outside air is shut off
and the air in the hull is recirculated by the blower.
At other times, the blower may use a mixture of fresh
and recirculated air. The battery ventilation system
provides for removal of gases generated when the batteries are on charge.
Each of the main batteries gets air from the living quarters
overhead. This air is drawn into the battery space
and as it circulates, it draws off the battery gases
In some installations, the ducts are replaced by an open circulation system.
The exhaust air is drawn out of the battery space by battery blowers
and is discharged into the main hull exhaust line.
Compressed air at various pressures is used for many purposes
throughout the boat. Two compressors in the after engine room
compress the air to a pressure of 3,000 pounds.
An external charging connection also makes it possible to take on
3,000 pound air from shore. The air is distributed through a manifold
in the control room to banks of storage bottles
located in the main ballast tanks. Some of it is used at 3,000 pounds,
some is reduced to lower pressures before being used.
This diagram of the 3,000 pound system shows a bank of storage bottles and the
manifold which is divided into a receiving
section and two distributing sections. The air
goes from the storage bank to the distributing sections of the
manifold. From there it is routed through piping
to blow special purpose tanks, to charge torpedoes,
to charge the hydraulic air flask, and to bleed air into the boat.
3,000 pound air is also used as a source for
lower pressure systems. Some is reduced by normal expansion to 600 pounds
and delivered to the manifold of the 600 pound air system.
This 600 pound air is used to blow the main ballast tanks.
Other 3,000 pound air is reduced by reducers to 225 pounds.
This air is delivered to another manifold.
The air in the 225 pound system is used to blow the variable ballast
tanks and to do such miscellaneous jobs as
blowing water from torpedo tubes, blowing sanitary tanks, and sounding the
Some 225 pound air is further reduced and used for a variety of jobs where
lower pressures are adequate. For this reason, this system is referred
to as ship's service air. In addition to these
systems, an independent 10 pound air system
operates from a blower in the pump room. The air from the blower is led to a
Lines from the manifold lead to the ballast tanks.
When the boat is surfacing, 600 pound air is used
to blow the main ballast tanks until the boat gets within a few feet of the
surface. 10 pound air is then used to finish
blowing the tanks. This conserves the high pressure air
needed to blow the tanks at greater depths.
The hydraulic system of a submarine employs oil
under pressure to operate such equipment as main vents,
flood valves, outboard induction and exhaust valves,
the steering system, the plane system, periscope and mast hoisting systems,
and many others. Oil is drawn from a supply tank
by a pump. It is delivered under pressure
to an accumulator. From here, it goes to various manifolds
which are connected to the hydraulically operated mechanisms
throughout the boat. Each manifold is divided into a supply side
which supplies oil under pressure to the mechanisms
and a return side through which the oil is returned to the tank.
And even pressure is maintained in the system by the accumulator.
As oil is pumped into the accumulator, it forces a piston down.
Near the bottom, the piston operates a pilot valve
which actuates a bypass valve so that the oil is bypassed back to the
suction side of the pump. High pressure air from a flask is
delivered to an air chamber below the piston. As the oil is used,
the air pressure forces the piston upward,
thus maintaining an even pressure on the oil system.
Near the top, the piston resets the pilot valve
which actuates the bypass valve so that the pump again forces oil into
the accumulator. This non-return valve maintains the
pressure on the system when the pump is discharging through the automatic bypass
or when the pump is shut down. The submarine's trim system is used to
shift seawater ballast for fore and aft trim
and for control of buoyancy. It consists of a trim pump, a trim manifold
in the control room, and lines from the manifold to the
variable ballast tanks, the negative tank, the safety tank,
and to sea. This trim system makes it possible to pump water from any variable
ballast tank to sea or from the sea into the tanks
or to shift water from any one of the variable ballast tanks
to another. The drain system provides for pumping of bilges.
Lines from the bilges lead to a drainage line
running the entire length of the submarine.
The drain pump draws water from the drain line
and discharges it overboard or to the trim system
or to the fuel oil compensating system. If the water is discharged to the
compensating system, oil in the bilge water will be separated
out in the expansion tank preventing telltale oil slates.
The drain pump also has a connection to the bottom of the collecting tank
for the pumping of that tank when necessary.
There are interconnections between the drain and the trim systems
so that either pump can be used for either system.
We have seen the most important equipment and machinery
necessary for the operation of the submarine.
The propelling machinery, which consists of the main engines
and their generators and the main motors,
which drive the propellers. The engines are used to provide power for the motors
when the submarine is on the surface or snorkeling.
Batteries power the motors when submerged.
The fuel oil and compensating system delivers fuel oil to the engines
and replaces used fuel with seawater. The air supply and exhaust system
supplies the air needed to run the engines.
It ventilates the boat and it removes engine exhaust gases.
The snorkel system provides for air intake and exhaust
when the boat is submerged. The battery ventilation system
removes gases from the batteries. The compressed air systems
distribute air furnished by two compressors.
The air is stored in banks at 3,000 pounds pressure.
This air is used directly or at reduced pressures
to blow tanks, charge torpedo impulse flasks
and for general ship's service. The 10 pound air system
is used to blow the residual water from the main ballast tanks
when the ship is surfacing. The hydraulic system
operates main vents, valves and other hydraulic gear
throughout the ship. The trim system is used primarily
to distribute weight in the boat for fore and aft trim
or overall buoyancy. The drain system is used primarily for pumping bilges.
The construction of the modern submarine employs the latest developments in
science and engineering to make it a formidable weapon against
the enemy.