On November 10, 2017, inside a test stand in Peebles, Ohio, engineers pushed a single engine to its absolute limit, maximum fan speed, maximum core speed, maximum exhaust gas temperature, every red line crossed simultaneously, and watched the readout climb past a number nobody had ever recorded for a commercial jet engine before: 134,300 pounds of thrust, enough raw force to lift an entire Airbus A320 straight off the ground using one single engine. That engine was the GE9X, and the record it set that day didn't just beat the previous mark, it obliterated it, smashing the GE90's long-standing thrust record by more than six thousand pounds. Built exclusively for the Boeing 777X, the GE9X carries a fan measuring a staggering 134 inches across, roughly as wide as the fuselage of a Boeing 737, spinning just sixteen massive composite blades instead of the twenty-two found on its predecessor, a deliberate engineering choice that trims weight while letting the fan spin faster and breathe more air than almost any engine ever built. Inside its core sit ceramic matrix composite turbine components, materials that can survive temperatures hundreds of degrees hotter than conventional metal alloys, paired with a comparatively simple two-spool architecture that GE has refined for decades specifically to chase higher thrust-to-weight ratios. On paper, it is a monster, designed to deliver roughly ten percent better fuel efficiency than the engine it replaces and a claimed five percent advantage over any other twin-aisle engine currently flying. But here is the twist in this rivalry: as of right now, the GE9X has never actually carried a single paying passenger anywhere, because the Boeing 777X itself remains stuck in certification limbo, which means every one of those staggering numbers is still, technically, a promise rather than a proven track record. Three thousand miles away, in the test cells of Rolls-Royce, sits the engine actually earning its reputation in the real world every single day: the Trent XWB. Smaller in nearly every dimension, with an eighteen-inch-narrower fan and a more conservative thrust range between eighty-four thousand and ninety-seven thousand pounds depending on the variant, the Trent XWB was never built to chase a thrust record. Instead, Rolls-Royce leaned into its signature three-spool architecture, three separate spinning assemblies instead of two, each one optimized to run at its own ideal speed, a more mechanically complex approach that trades some of GE's raw simplicity for smoother, more stable performance across an enormous range of altitudes and flight conditions. Since entering commercial service back in 2015 powering the Airbus A350, the Trent XWB has quietly logged more than two million flight hours with a dispatch reliability rate north of ninety-nine percent, numbers so strong that Rolls-Royce confidently calls it the most efficient large aero-engine flying anywhere in the world today, a claim that is hard to argue with given the engine actually has years of real airline operating data to back it up. So this comparison really comes down to a question of proof versus potential. The GE9X holds the record books, the bigger fan, the higher claimed thrust, and a genuinely radical leap in materials engineering, but it is still waiting in the wings for its airplane to finally clear certification. The Trent XWB holds something arguably more valuable in commercial aviation: more than a decade of uneventful, dependable, fuel-sipping performance on one of the most popular widebody aircraft flying today. When the 777X finally does enter service and the GE9X starts accumulating its own real-world flight hours, this rivalry will stop being theoretical, and aviation engineers everywhere will finally get to see whether raw power or refined reliability wins the long game.
Two engines. Two completely different philosophies.
One of them is the single largest jet engine ever bolted onto an airplane.
The other powers what might be the most efficient widebody flying today.
And here's the kicker, they almost never go head-to-head in real life
because they were each built for one specific airplane and nothing else.
Today, we're putting the General Electric GE9X up against the Rolls-Royce Trent XWB,
round by round, fact by fact, to figure out which one actually comes out on top.
Stick around, because by the end of this, the answer is going to surprise you.
Let me set the stage first, because it matters.
The GE9X was built for one machine and one machine only.
Boeing's enormous new 777X.
The Trent XWB? Same exact story.
But for the Airbus A350.
So in a weird way, this isn't just an engine comparison.
This is Boeing's vision of the future of long-haul flight
hanging right there under the wing.
Two of the biggest names in aerospace, going at it the only way they really can,
through the metal they bolt onto their flagships.
So when you pick a winner here, you're not just picking an engine,
you're kind of picking a side.
And I should be upfront about something, because it shapes this whole comparison.
These two engines aren't even in the exact same weight class.
The GE9X is a 110, 0-0-0 pound thrust engine.
The Trent XWB tops out around 97,000.
So in pure thrust terms, they're not direct competitors
the way two cars in the same price bracket would be.
But that's exactly what makes this match-up so fascinating.
Because despite that gap, these are the two newest,
most advanced large wide-body engines on the planet,
built by the two biggest engine makers in the world,
for the two flagship airplanes of the two biggest planemakers.
They represent the absolute state of the art,
right now, in 2026.
If you want to understand where jet propulsion stands at this very moment,
you compare these two.
Bigger isn't the only thing that matters, and that's the whole point.
I'm going to run this as a fight.
Six rounds. Size, thrust, efficiency, technology,
real world track record, and cold hard money.
I'll call each round honestly, even when the honest answer is,
it's a draw, or we don't actually know yet.
And at the end, I'll give you my real verdict.
Plus a question I genuinely want you to answer in the comments.
Deal? Let's go.
All right, let's get into it.
Round one. Size.
And Cara, this one is not even a contest.
The GE9X is the single largest commercial jet engine ever built.
Full stop.
Its fan measures 134 inches across.
That's 3.4 meters.
Let that number sit with you for a second,
because it's hard to actually picture.
The fan at the front of this engine is nearly as wide
as the entire fuselage of a Boeing 737.
You could basically take the body of a narrow body airliner,
the kind of plane you fly on for a domestic trip,
and roll it straight through the front opening of this engine.
GE's own engineers love pointing out that the fan is taller
than a regulation NBA basketball hoop by a full foot.
The whole engine, nacelle, and all is around 161 inches in diameter.
It's a building with blades.
And when this thing spins up to full power on a test stand,
it generates so much airflow behind it
that GE has described the wake as a miniature Category 5 hurricane.
That's not marketing fluff,
that's just the physics of moving that much air.
Now, let's look at the Trent XWB.
Its fan measures 118 inches,
which works out to right around 3 meters.
And listen, by any normal standard on earth,
that is still an absolutely enormous piece of machinery.
If the GE9X didn't exist, we'd be calling the Trent XWB a giant.
But next to the GE9X, it's clearly the smaller engine.
The General Electric power plant has a fan
that's about a foot and a half wider in diameter.
That's a massive gap when you're talking about precision aerospace hardware.
So if this round is purely about who is physically bigger,
GE takes it without breaking a sweat.
The GE9X is the undisputed heavyweight champion of the entire engine world.
Nothing else in commercial service comes anywhere close to it.
Let me give you one more way to feel the scale here,
because numbers on a screen don't always land.
Stand a person next to a GE9X
and they barely come up to the middle of the fan.
A technician working on this engine is genuinely dwarfed by it,
the same way they were by the GE90 before it.
The fan case alone is wider than the fuselage of a Boeing 737.
If you've ever flown on a typical short domestic hop,
the tube you were sitting in would basically disappear inside the front of this engine.
And it's not just for show.
All that diameter exists to move an enormous mass of air slowly,
rather than a small mass of air quickly,
because moving more air more gently is both more efficient and quieter.
The size is the efficiency strategy.
That's the whole reason GE went so big.
But, and this is a big but,
I need you to stop right here,
because bigger does not automatically mean better.
And honestly, that's the whole trap this comparison is built around.
People see the size and assume the GE9X wins everything.
The reality is so much more interesting than that.
Round two.
Raw thrust.
How hard can each of these engines actually push?
You'd assume the giant wins again, right?
It's bigger, so it must be stronger.
Wrong.
And this is genuinely one of my favorite facts in all of modern aviation,
so pay attention.
The GE9X is certified at 110,000 pounds of thrust in airline service.
The Trent XWB tops out at 97,000 pounds in its most powerful version,
the one they call the XWB-97.
So on the official rated numbers,
yes, the GE9X is the stronger engine by about 13,000 pounds of thrust.
It takes the round.
But the story sitting underneath those numbers is wild.
Back on November 10th, 2017,
at GE's outdoor test facility in Peebles, Ohio,
a GE9X was pushed to its absolute breaking point.
Maximum fan speed, maximum core speed,
and maximum exhaust gas temperature all at the same time.
Engineers call that a triple redline test.
It's basically asking the engine to give you everything it has
and then a little more right up to the edge of destruction.
And the engine cranked out 134,300 pounds of thrust.
That set a Guinness World Record
for the most thrust ever produced by any jet engine in history.
And here's the detail that makes it even better.
The engine it beat to claim that record?
The GE90-115B, which had held the title at 127,900 pounds.
And the GE90 is the GE9X's own direct ancestor.
So General Electric literally broke its own world record.
The student became the master.
And here's a fun wrinkle in that story.
When the GE90 set its record of 127,900 pounds back in 2002,
it actually happened almost by accident
during a one-hour triple redline stress test
on a development engine in Peebles.
The engineers weren't even trying to set a record.
They were just pushing the engine to its limits
to prove it could survive abuse.
And it casually shattered the world record in the process.
The GE9X did something similar in 2017.
Except this time, GE more or less knew what was coming.
David Joyce, who ran GE Aviation at the time,
said they didn't set out to break the thrust record.
They were proud of the performance.
But the record was a byproduct of just how capable the engine is.
There's something wonderfully GE about that.
They build engines so overpowered
that they break world records as a side effect of routine testing.
If the GE9X can physically produce 134,000 pounds of thrust,
why is it only rated at 110,000 in service?
Great question.
Because it doesn't need any more.
The Boeing 777X is so aerodynamically efficient,
especially that gorgeous new composite wing with the folding wingtips,
that GE was actually able to dial the engine back.
Think about how absurd that is for a second.
They built the most powerful jet engine in the history of human flight
and then told it to take it easy.
There's headroom in this engine that the airplane simply doesn't require.
The Trent XWB doesn't play that particular game.
It produces almost exactly what the A350 needs and not a whole lot more.
Different philosophy entirely.
So round two goes to GE on the official rated numbers
and GE owns the absolute thrust record on top of it.
But Rolls-Royce would gently remind you
that brute force was never really the point of their engine.
And hey, if you're enjoying this match-up so far,
do me a quick favor and hit that like button
and subscribe if you want more aviation deep dives like this one.
It genuinely helps the channel more than you'd think.
And it's free.
Okay, back to it.
Round three.
Efficiency.
And now, finally, the Trent XWB gets to flex its muscles.
Because this is the round Rolls-Royce was built to win.
Rolls-Royce flat out calls the Trent XWB
the most efficient large aero engine in commercial service
and they've got real-world data to back the claim up.
According to Rolls-Royce, the Trent XWB burns roughly 15% less fuel
than the very first Trent engine they ever made back in the 1990s.
And it's a huge part of why the Airbus A350 burns around 25% less fuel
than the previous generation of widebodies it was designed to replace.
That's not a small improvement.
On a long-haul flight across an ocean,
that's tons of fuel and tons of CO2 that simply never get burned.
So how does the Trent XWB pull this off?
A few clever things.
It runs a bypass ratio of about 9.6 to 1
and an overall pressure ratio right around 50 to 1.
But the real Rolls-Royce signature,
the thing that makes a Trent a Trent, is the architecture.
This is a three-shaft engine, three concentric spools,
all nested inside each other,
all spinning completely independently at their own ideal speeds.
The fan and its turbine on one shaft,
the intermediate compressor on another,
the high-pressure core on a third.
And to make the efficiency real for you,
let's talk actual fuel numbers,
because this is where it stops being abstract.
An A350-1000,
cruising along burns dramatically less fuel
than the previous generation jet it replaces,
the Boeing 777-300ER.
Industry analysis pegs the A350-1000
at burning something like 8,800 pounds of fuel per hour in cruise
versus roughly 11,000 pounds per hour for the 777-300ER.
That's a difference of around 2,200 pounds of fuel every single hour.
On a 14-hour flight,
that adds up to roughly 30,000 pounds of fuel saved on a single trip.
Thousands of gallons, tens of thousands of dollars on one flight
multiplied across thousands of flights a year.
That is the entire reason airlines fell in love with the A350
and its Trent XWB engines.
Efficiency isn't a bragging right in this business.
It's the difference between a route making money and losing money.
GE, by contrast, uses a simpler two-shaft design.
Now, the three-shaft layout is heavier
and genuinely more complex and more expensive to build.
Nobody disputes that.
But the payoff is that each section of the engine
gets to spin at exactly the rotational speed that's most efficient for it
instead of being forced to compromise.
It also lets Rolls-Royce build a shorter, stiffer, more compact engine.
It's an elegant solution,
and Rolls-Royce has spent literally decades
perfecting it across the entire Trent family.
Now, does the GE9X just give up on efficiency and rely on being big?
Absolutely not.
And this is where the round gets genuinely close.
The GE9X was specifically designed to be 10% more fuel efficient
than the GE90 that came before it,
and it does that partly through a monster overall pressure ratio of 61 to 1.
That is one of the highest overall pressure ratios in all of commercial aviation,
and it's significantly higher than the Trent's roughly 50 to 1.
What that means in plain language is that the GE9X
squeezes and compresses the incoming air far more aggressively
before burning fuel in it.
And the more you compress that air,
the more energy you can extract from every single pound of jet fuel.
GE went after efficiency through sheer thermodynamic intensity in the core.
GE even claims the GE9X should deliver about 5% lower specific fuel consumption
than the Trent XWB97.
But, and this is important,
that's a design target for an engine that's barely started its airline career.
So who actually wins efficiency?
Here's the honest answer, and I'm not going to fudge it.
It depends entirely on how you measure it.
The Trent XWB has years and years of real-world,
in-service data across hundreds of airplanes
proving its fuel burn day in and day out.
The GE9X has a higher pressure ratio,
newer technology,
and impressive design targets,
but a tiny fraction of the real-world commercial flight hours.
On proven, in-service, money-in-the-bank efficiency,
I'm giving this round to the Trent XWB.
It has been quietly sipping fuel across the world's oceans since 2015,
and the results are no longer theoretical.
GE's numbers are exciting,
but they still have to be proven in daily airline service over years.
Round 4 – Technology and Materials
This is the nerd round, and I love this one,
because it's gloriously close,
and both companies took completely different paths to get to greatness.
The GE9X is absolutely packed with stuff that sounds like science fiction.
Start with the materials.
It uses ceramic matrix composites,
an incredible lightweight material,
in the hottest sections of the engine,
the combustor,
and the turbine.
We're talking about components that hold their structural strength
at temperatures approaching 2,400 degrees Fahrenheit,
a temperature at which even the best traditional metal superalloys start to go soft.
Ceramics can take heat that metal simply can't,
and being able to run the core hotter is a direct path to more efficiency.
Then there's the manufacturing.
GE3 deprinted several components of this engine.
The fuel nozzles in that advanced TAPS3 combustor are additively manufactured,
printed layer by layer out of a cobalt-chrome superalloy into intricate shapes
you simply could not machine the old way.
There are 28 of those fuel nozzles,
and the clever internal geometry that 3D printing makes possible
is a big part of how the engine mixes fuel and air so cleanly,
which is exactly why GE can claim NOx emissions up to 55% below regulatory limits,
roughly half those of competing engines in its class.
And the fan, that record-setting 134-inch fan,
uses just 16 carbon fiber composite blades.
The old GE90 needed 22 blades to do its job.
Fewer blades means less weight,
less drag from the wake of each blade,
and more efficiency.
There's a neat detail here too.
Those blades have steel leading edges and fiberglass trailing edges,
specifically engineered to flex and absorb bird strikes
better than rigid carbon fiber alone could.
They're the fourth generation of composite fan blade technology,
and GE is still the only engine maker that has truly mastered this particular art at this scale.
Let me dwell on those ceramic matrix composites for a second,
because they're arguably the single most important materials breakthrough in the whole engine.
Traditional jet engines are limited by one brutal fact.
The hotter you run the core, the more efficient you can be.
But metal can only take so much heat before it weakens,
and you have to bleed precious air away from making thrust just to cool the metal parts.
Ceramics flip that equation.
Because CMC parts can withstand temperatures
approaching 2,400 degrees Fahrenheit without going soft,
GE can run the core hotter and bleed off less cooling air,
which directly boosts both efficiency and durability.
It's lighter than metal, too.
This is technology that GE actually first matured on a G-X demonstrator engine
before bringing it to the GE 9X,
another example of that GE family lineage paying dividends.
Getting ceramics to survive inside a jet engine,
with all the vibration and thermal shock and stress,
is one of the genuine engineering triumphs of the last couple of decades.
And the high-pressure compressor on the GE 9X runs an astonishing 27 to 1 pressure ratio
all on its own, using 11 compressor stages,
up from the 19 to 1 and fewer stages on the GE 90.
That core is a pressure-building monster.
Now the Trent XWB answers with its own deep arsenal,
and don't think for a second it's outgunned.
It uses 22 swept titanium fan blades,
carefully shaped for aerodynamic efficiency.
It introduced a two-stage intermediate pressure turbine,
a change from the single stage on earlier Trents,
specifically for better efficiency and more thrust capability.
It uses intelligent air management systems that constantly minimize
how much precious cooling air the engine has to bleed off,
because every bit of air you don't waste on cooling is air you can use to make thrust.
It uses a single-skin combustion casing to cut weight and simplify maintenance,
and its combustor runs advanced ceramic coatings
that let it operate at temperatures above 2000 Kelvin
while keeping fuel burn and emissions low.
And here's a stat that always blows people's minds.
A single high-pressure turbine blade in the Trent XWB
generates around 800 horsepower, one blade.
A blade roughly the size of your hand is putting out the power of a serious sports car,
and there are dozens of them on that disc, all spinning together, all white-hot.
And to get the higher thrust XWB-97 from the baseline XWB-84,
Rolls-Royce didn't just turn up the wick.
They kept the same 3-meter fan, but spun it about 6% faster,
which meant strengthening the fan blades and the fan casing to handle the increased forces.
And they scaled up the core by about 5% to push more air through it at higher temperatures.
It's a masterclass in extracting more performance from a proven design without starting over.
The XWB also drew on technology from a big European research program
called the Environmentally Friendly Engine Initiative.
This is what decades of institutional knowledge looks like when it's applied with precision.
So these are two radically different engineering answers to the exact same question.
GE went all-in on exotic new materials,
additive manufacturing, and pushing temperature and pressure to extremes.
Rolls-Royce took its proven, beloved three-shaft formula,
and refined it to within an inch of perfection,
squeezing efficiency out of architecture and meticulous detail.
Honestly, I genuinely cannot give a clean win here to either side.
They're both masterpieces, built on opposite engineering philosophies.
This round is a draw, and I think calling it anything else would be dishonest.
But here's where things get really interesting, because engines aren't just spec sheets.
They have to survive the real world.
Which brings us to the next round.
Actually, before we go there, let me geek out for one more minute.
Because if you really want to understand why these engines behave so differently,
you have to look at how they're built on the inside.
And it's genuinely beautiful engineering on both sides.
Picture air entering the front of the engine.
On both machines, it hits that giant fan first.
After the fan, the air splits into two streams.
Most of it, the bypass air,
rushes around the outside of the engine core and produces the bulk of the thrust.
That's why a high bypass ratio matters so much.
The rest of the air gets pulled into the core to be compressed,
burned, and used to drive the turbines that spin everything.
Now, on the GE9X, that core air goes through a system built around two spools,
two concentric shafts.
There's a low-pressure spool connecting the fan and the booster compressor
to the low-pressure turbine at the back.
And there's a high-pressure spool connecting that 11-stage high-pressure compressor
to the high-pressure turbine.
11 stages of compression in the high-pressure section alone.
Each stage squeezing the air tighter and tighter,
building up to that 27-to-1 core pressure ratio and the 61-to-1 overall pressure ratio.
The hotter and more compressed you can run that core,
the more energy you extract from the fuel.
And to survive those brutal temperatures,
that's exactly where the ceramic matrix composites earn their keep,
in the combustor and the first turbine stages where it's hottest.
The Trent XWB does something fundamentally different,
and this is the heart of the whole Rolls-Royce philosophy.
Instead of two spools, it uses three.
Three separate, concentric, independently spinning shafts.
There's the fan and its low-pressure turbine on one shaft.
Then, an 8-stage intermediate pressure compressor
driven by its own intermediate pressure turbine on a second shaft.
Then, a 6-stage high-pressure compressor
driven by a single-stage high-pressure turbine on a third shaft.
And here's a gorgeous detail.
That high-pressure shaft actually rotates in the opposite direction to the other two.
The annular combustor feeds it all,
with around 20 fuel spray nozzles,
controlled by a dual-channel, full-authority digital engine control computer,
what engineers call FAC.
Why go to all the trouble of three shafts?
Because it lets each compressor spin at its own optimal speed
instead of forcing a compromise.
The fan wants to turn slowly,
the high-pressure core wants to turn fast,
and a three-shaft design lets each one do exactly what it wants.
It also makes for a shorter, stiffer engine.
The downside is obvious.
More shafts, more bearings, more complexity, more weight, more cost.
Rolls-Royce decided that trade-off was worth it,
and they've spent decades proving they can build it reliably.
So in one engine, the GE9X,
you've got a simpler, two-shaft layout pushed to thermodynamic extremes
with exotic materials and a monster pressure ratio.
In the other, the Trent XWB,
you've got a more complex, three-shaft layout refined to a mirror polish over generations.
Two completely different roads to the same destination,
moving a few hundred people across an ocean
while burning as little fuel as humanly possible.
I find that contrast genuinely beautiful,
and it's why this comparison is so much richer than just,
which one is bigger?
Okay, now let's get to the round that really matters in the real world.
Round five, track record and reliability.
Who is actually out there flying every single day,
carrying real passengers across real oceans?
Because this, in the end, is what an engine is actually for.
Not test stands, not world records, not spec sheets.
Real flights, real people, real reliability.
And right now, in this specific moment, the gap here is enormous.
The Trent XWB entered commercial service back in 2015.
Its launch customer was Qatar Airways on the Airbus A350-900.
And since then, it has become the fastest selling wide-body engine in history,
with well over 1,600 units sold.
There are two main versions out there flying.
The XWB-84, which produces around 84,000 pounds of thrust for the A350-900,
and the bigger XWB-97, which delivers up to 97,000 pounds
for the larger A350-1000 and the upcoming A350 freighter.
Rolls-Royce quotes a 99.9% dispatch reliability rate on the XWB-97.
These engines have collectively crossed the planet millions and millions of times.
When you fly on an A350 today, and a lot of people do,
you are sitting behind a Trent XWB, and it just works.
The GE-9X?
It is a genuine beast on paper and an absolute monster on the test stand.
It was fully certified by the FAA back in September of 2020.
Let me say that again.
It's been certified and ready since 2020.
It went through the single most rigorous testing program
of any commercial engine GE has ever built,
racking up tens of thousands of test cycles and thousands of hours,
including grueling dust ingestion tests
designed to prove it can handle the arid, sandy regions where the 777X will operate.
And the scale of that testing program is honestly staggering.
By the time GE was done,
the GE-9X had passed through more than 31,000 total engine test cycles,
including over 9,000 endurance cycles and thousands of dust ingestion cycles
specifically to validate durability in harsh, sandy environments.
GE has described it as the equivalent of nearly two years of round-the-clock, 24-7s testing.
The certification effort involved eight separate test engines,
plus another dedicated to ETOPS certification,
the approval that lets a twin-engine jet fly long routes far from any diversion airport.
Testing happened across multiple sites,
the massive Peebles, Ohio facility, an altitude test cell in Evendale,
and cold weather and icing work up in Winnipeg, Canada.
They pelted this engine with ice, sucked debris and dust into it,
ran it at crosswinds, tested for bird strikes,
all before it ever carried a single paying passenger.
When the engine finally got its certificate,
it had been validated about as thoroughly as any engine in history.
But the GE-9X has a problem, and it's not the engine's fault.
Its airplane, the Boeing 777X, has been hammered by years and years of delays.
The program was originally supposed to deliver its first jet around 2020.
As of now, those first deliveries have slipped all the way to 2027,
roughly seven years behind the original schedule.
So you've got this magnificent, record-shattering engine,
fully certified, sitting essentially ready to go,
and it's been waiting and waiting for its airplane to finally show up to the party.
It's a Formula One engine without a race to run yet.
So in terms of proven, in-service, real-world airline reliability,
the Trent XWB wins this round decisively.
And it's not because it's necessarily the better-engineered machine.
It's because it has actually been doing the job,
reliably, day in and day out, for over a decade now.
Real flight hours beat test stand records
when it comes to trusting an engine with hundreds of lives.
Round six.
Let's talk money, because for the people who actually buy these engines,
the airlines, this might be the most important round of all.
And this is where things get genuinely complicated for the Trent XWB,
despite all its strengths.
Here's the deal.
The big, efficient fan and hot-running core that make a modern engine fuel-efficient
also make it run hot, and hot engines wear faster.
This is the central tension of every cutting-edge engine.
Chase efficiency too hard, and you can pay for it at the maintenance shop.
The higher-thrust Trent XWB-97, the one on the A350-1000,
has been at the center of exactly this debate.
Tim Clark, the President of Emirates, said publicly at the 2023 Dubai Air Show
that the XWB-97 would offer only about a quarter of the time
between maintenance visits that his airline needs,
particularly worrying for an airline that operates
in the brutally hot and sandy conditions of the Gulf.
That's a serious complaint from one of the most powerful voices
in the entire airline industry.
Now, there's nuance here, and I promised you honesty.
Some analysts, including ones at Citigroup,
suggested those comments were partly a hardball negotiating tactic,
a way to push Rolls-Royce on price and guarantees.
And crucially, Qatar Airways operates the very same XWB-97 engine
in a very similar hot and sandy environment
without reporting those same major durability problems.
So is it really an engineering flaw, or is it commercial theater?
Probably some of both.
Rolls-Royce, for its part, has been actively working with Emirates
to improve the engine's durability in hot and sandy conditions.
And it's worth saying that the lower-thrust XWB-84,
the workhorse on the A350-900,
has had a famously clean reliability record.
Rolls-Royce even noted that fleet-leading XWB-84 engines
have flown over 22,000 hours without needing a shop visit,
which is genuinely excellent.
The GE-9X has a relevant claim here, too.
GE has said the GE-9X is designed to deliver maintenance costs
comparable to the GE-90-115B,
an engine with a long and well-understood maintenance history
that airlines trust.
But, and you knew there was a but,
the GE-9X simply hasn't proven its real-world in-service maintenance costs yet,
because it isn't in regular service yet.
Predicted maintenance costs and actual maintenance costs
are two very different animals,
and the only way to know for sure is years of airlines
actually operating the engine and tracking what breaks and when.
So who wins the money round?
Honestly, it's too close and too unproven to call cleanly.
The Trent XWB-84 has a track record of low operating cost and high reliability.
The Trent XWB-97 has real,
public question marks about durability in harsh climates.
The GE-9X has promising predicted costs
and a parts commonality story with the trusted GE-90,
but zero real-world airline maintenance data.
I'm going to call this round a draw with an asterisk,
leaning slightly toward,
we genuinely don't know yet for the GE-9X,
and that uncertainty itself is part of the story.
Now, I want to be fair,
because no engine story is all sunshine.
Both of these power plants have had real-world growing pains,
and pretending otherwise would be dishonest.
The Trent XWB has had a handful of notable incidents in service.
Back on September 11th, 2018,
an Iberia A350-900 had to divert to Boston
after one of its Trent XWB engines shut down in flight at 41,000 feet
on a trip from New York to Madrid,
an issue reportedly traced to the variable stator vanes.
That was the engine type's first in-flight shutdown,
and at that point, the fleet had already racked up 2.2 million flight hours,
so statistically, it was a remarkably clean record up to then.
More recently, on September 2nd, 2024,
a Cathay Pacific A350-1000
powered by the Trent XWB-97 suffered an in-flight engine fire.
The crew handled it, and the aircraft landed safely.
Cathay then inspected every single one of its 48 A350s
and found several with a similar defect,
reportedly a damaged flexible fuel line.
The European Union Aviation Safety Agency
responded by requiring a one-time inspection across the Trent XWB fleet,
and there's an ongoing storyline about the higher thrust XWB-97
and how well it holds up in hot, sandy operating environments.
Tim Clark, the President of Emirates,
has been publicly critical about its time
between maintenance visits in tough climates.
Rolls-Royce has been working on durability improvements,
and it's worth noting that Qatar Airways
operates the very same engine in a hot, sandy environment
without reporting those same major issues.
So how much of that is engineering,
and how much is commercial negotiation tactics
is genuinely up for debate.
The GE9X had its own development bumps along the way.
The program hit a snag with the high-pressure compressor's
variable stator vane lever arms before its first flight,
an issue discovered in early 2018 that GE worked through.
And in 2022, a separate issue with the GE9X
paused testing of the 777X,
contributing to the program's long string of delays.
These are the kinds of problems you expect
and want to find during a thorough development program
rather than after the engine is in service.
That's literally what all those tens of thousands
of test cycles are for, to surface problems on the ground
where they're cheap and safe to fix,
not at 40,000 feet over the ocean.
And to GE's credit, the engine ultimately powered
through the most extensive testing campaign
in the company's history to earn that certification.
It's worth remembering that the GE90 itself
had a genuinely rocky start in the late 1990s
with technical setbacks and a brutal aviation recession,
and it went on to become one of the most reliable
and successful engines ever built.
Early turbulence in a development program
doesn't define an engine's eventual legacy.
The GE9X's real test is still ahead of it,
out in daily airline service.
So when you stack up reliability,
the Trent XWB has the enormous advantage
of a proven, mature, in-service track record,
warts and all.
The GE9X has a spotless certification record
but still has to prove itself
in the unforgiving environment of daily airline operations.
And that's a test no amount of ground testing
can fully replace.
Now I want to zoom out
because to really understand these two engines,
you have to understand where they came from.
Engines like this don't appear out of nowhere.
They're the latest chapter in stories that go back decades.
Let's talk about the GE9X's bloodline first
because it's a great story.
The GE9X is essentially the fifth evolution
of a legendary engine called the GE90.
And the GE90 itself was a gamble
that nearly broke General Electric.
Back in the early 1990s, GE was, frankly, the underdog.
They set out to build an all new, clean sheet engine
for Boeing's brand new 777
while their rivals, Rolls-Royce and Pratt & Whitney,
mostly offered modified versions of existing engines.
GE poured something like $1.5 billion into the GE90
and some of its core technology
actually traces back to joint research
between GE and NASA in the 1970s.
The GE90 entered service with British Airways
in November of 1995
on a flight from London Heathrow to Dubai
and the early days were rough.
There were gearbox bearing wear problems
that forced British Airways to pull its 777 fleet
off transatlantic routes for a while in 1997.
The engine was expensive, it was heavy
and the media at the time
absolutely went after GE over the cost.
In fact, British Airways, the launch customer,
soon switched its 777S over to the Rolls-Royce Trent 800.
Ouch.
There's even a great piece of trivia here.
In 1998, GE took a $275 million tax write-off
after cancelling an upgrade program for the engine
and in 1997, a new president named Jim McNerney took over
and spearheaded one of the most dramatic turnarounds
the engine industry has ever seen.
But GE held on and the gamble paid off spectacularly.
When Boeing launched the second generation 777,
the long-range 777, 300ER and 777-200LR,
it chose the higher thrust GE90 as the exclusive engine.
That exclusivity was the turning point.
The GE90 went on to power the 777
into becoming the long-haul workhorse
of the entire global fleet.
More than 3,000 GE90 engines have been built.
The fleet has logged well over 100 million flight hours
and built a dispatch reliability rate around 99.98%.
One of its carbon fiber fan blades was so groundbreaking
that the Museum of Modern Art in New York
added one to its collection,
an engine blade in an art museum.
That's the legacy the GE9X inherited.
It carries the GE90's DNA
and it was built to carry that torch into the next era.
And the through line of innovation
in that family is remarkable.
The GE90 was the first commercial engine
to use carbon fiber composite fan blades
instead of metal ones,
a genuinely radical move at the time
that everyone said was risky.
Those composite blades were about a third
of the weight of titanium ones while being even stronger.
And that single decision rippled forward
through GE's entire lineup,
the G-ANX that powers the 787 Dreamliner
and the 747-8,
the CFM LEAP that powers narrowbodies
and ultimately the GE9X.
Many of the GE9X's headline tricks,
the record power,
the composite blades,
the hot and harsh climate durability work
were first proven on the GE90.
So when you look at the GE9X,
you're not looking at a clean sheet gamble.
You're looking at the fifth refinement of a formula
that's been winning for 30 years.
Now the Trent XWB's story is just as fascinating
and in a way, it's a mirror image.
The Trent name goes all the way back
to the early 1990s for Rolls-Royce,
named after the River Trent in England,
continuing a tradition where Rolls-Royce
names its big civil engines after rivers.
The Trent family grew engine by engine,
the Trent 700 for the Airbus A330,
the Trent 800 for the Boeing 777,
the Trent 900 for the giant Airbus A380,
the Trent 1000 for the Boeing 787 Dreamliner.
Each generation layered on new technology
and that constant refinement made Rolls-Royce
the second biggest supplier of large civil engines
in the world behind only GE.
By 2019, the Trent family as a whole
had piled up over 125 million flight hours.
This is one of the great engine dynasties
in aviation history and the XWB
is its current crown jewel.
What's interesting is that every Trent
kept that signature three-shaft architecture
generation after generation while refining it.
The Trent 800, for example,
was the most popular engine choice
on the original Boeing 777,
beating GE's heavier GE90 in those early years.
So Rolls-Royce and GE have been trading blows
on the exact same airframes for decades.
On the original 777,
Rolls-Royce's Trent 800 often won.
On the new 777X,
GE locked in exclusivity with the GE9X
and Rolls-Royce isn't even in the running.
On the A350, it's the reverse.
Rolls-Royce is exclusive and GE isn't offered.
This rivalry runs deep
and it's been going back and forth for over 30 years.
The Trent XWB itself was born out of a fight
Airbus was having with Boeing.
In the mid-2000s, Airbus was under intense pressure
to respond to Boeing's revolutionary 787 Dreamliner.
Airbus's first plan was a fairly modest upgrade
of the existing A330
and Rolls-Royce proposed a derivative engine
called the Trent 1700 to power it.
But the airlines weren't impressed.
They wanted something genuinely new.
So in 2006, Airbus scrapped the half-measure,
committed billions to an all-new clean-sheet airplane,
the A350 XWB,
and turned to Rolls-Royce for an all-new engine to match.
The result was the Trent XWB,
selected in July of 2006
to be the exclusive power plant of the A350.
The XWB, by the way, stands for Extra Wide Body,
which is Airbus branding for the A350's wider fuselage.
And as Airbus refined the airplane and its weight crept up,
the engine had to grow with it.
The most powerful version eventually got uprated
to that 97,000 pounds of thrust
to meet the A350-1000's higher takeoff weight.
And to get there,
Rolls-Royce spun the fan 6% faster and beefed up the core.
The Trent XWB first ran on a testbed in 2010,
first flew mounted on an Airbus A380 flying testbed in 2012,
was certified in early 2013,
and entered service in 2015.
And it has been a roaring commercial success ever since,
the fastest-selling wide-body engine ever made.
So look at the symmetry here.
The GE9X is the latest evolution of GE's GE90 dynasty,
built exclusively for a Boeing.
The Trent XWB is the crowning achievement
of Rolls-Royce's Trent dynasty,
built exclusively for an Airbus.
Two proud engineering houses,
two flagship airplanes,
two completely different philosophies
of how to move a few hundred people across the world.
Quick question for you while we're here,
and I really want you to answer this one in the comments.
When you fly, do you even notice or care
which engines are under the wing?
Or is it just background noise to you?
I'm genuinely curious where this audience lands,
so let me know down below.
Now, here's something that's easy to forget.
An engine on its own is just a beautiful piece of metal.
It only matters because of the airplane it lifts into the sky.
And the two airplanes these engines were built for
tell you exactly why each engine turned out the way it did.
So let's talk about the planes for a minute,
because they completely shape the engines.
The Boeing 777X, the home of the GE9X,
is an absolute monster of an airplane.
The main version, the 777-9,
stretches almost 252 feet long.
That's nearly 77 meters.
It typically seats around 426 passengers in a two-class layout,
making it the largest twin-engine commercial aircraft ever built.
Full stop.
It has the biggest wingspan of any commercial passenger jet,
and the wing is so enormous that Boeing had to design folding wingtips,
an industry first on a jet this size,
just so the thing can fit at normal airport gates.
When you build an airplane that huge, that heavy, that hungry for lift,
you need an engine that can move colossal amounts of air.
You need the GE9X.
The plane demanded the biggest engine ever made,
and so that's exactly what GE built.
But here's the fascinating twist.
The 777-9 is optimized for raw capacity,
for cramming the maximum number of people and cargo into a single jet,
not for absolute distance.
Boeing lists its range at around 7,285 nautical miles.
That's plenty for the vast majority of long-haul routes on Earth,
but it's actually shorter than its rival.
The 777X is the high-capacity hub-to-hub workhorse.
More than half of all its firm orders come from just two carriers,
Emirates and Qatar Airways,
airlines that fill enormous planes on dense international routes
out of their Gulf mega-hubs.
Now the Airbus A350, the home of the Trent XWB,
took the opposite approach,
and that's the key to understanding the Trent.
The A350-1000.
The bigger passenger version is a touch shorter at around 241 feet,
and it typically carries somewhere around 350 to 370 passengers.
So it's a smaller airplane than the 777-9.
But it flies farther,
with Airbus quoting a range comfortably beyond 8,500 nautical miles
for the standard A350-1000,
well past what the 777-9 manages.
The A350 is built from advanced composite materials,
which makes it the lightest widebody in its class,
and Airbus says that lightness translates
into roughly 25% lower operating costs
compared to the previous generation.
See the pattern?
The 777X is bigger and carries more people.
The A350 is lighter, more efficient, and flies farther,
and the engines mirror their airplanes perfectly.
The GE9X is huge and powerful
because the 777X is huge and needs power.
The Trent XWB is lighter and obsessively efficient
because the A350 is lighter and obsessively efficient.
The engine is a reflection of the airplane's entire personality.
You genuinely cannot understand one without the other.
An engine is designed hand-in-glove with its airframe,
the two teams talking constantly,
trading weight and thrust and fuel burn targets back and forth
until the whole package clicks.
So when people argue about which engine is better in a vacuum,
they're kind of missing the point.
The GE9X is the perfect engine for the 777X.
The Trent XWB is the perfect engine for the A350.
Each one is exactly as good as it needs to be
for the job it was hired to do.
And there's a real-world consequence to all of this
that's playing out right now in the airline industry.
Because the 777X has been delayed for years
and the GE9X has been waiting on it.
Airlines that needed new widebodies couldn't wait,
so they ordered A350s instead.
The A350 family has racked up well over 1,500 orders
with hundreds already flying.
The Trent XWB has been able to define
the entire upper-end widebody segment
basically uncontested for years
purely because its airplane showed up on time
and the competition didn't.
That is a massive quiet advantage
that has nothing to do with which engine is technically superior
and everything to do with timing.
In aviation, being available beats
being theoretically better almost every single time.
Let me put some real names to this
because the airline side of the story is fascinating.
The Trent XWB powers the A350S
of some of the most prestigious carriers on the planet.
Qatar Airways was the launch customer back in 2015
and built a huge part of its premium long-haul identity
around the A350.
Singapore Airlines uses the A350
including a special ultra-long-range version
to fly the longest commercial route in the world,
Singapore all the way to New York,
a flight that can push close to 19 hours in the air.
Think about that.
The Trent XWB has to run reliably for nearly a full day nonstop
over the Arctic and the Pacific without skipping a beat.
Rolls-Royce points out that nine of the 10
most profitable airlines in the world
have chosen the Trent XWB 8-4.
That's not an accident.
That's a decade of building trust one flight at a time.
The GE9X meanwhile has its dance card already full
waiting for the 777X to actually arrive.
Lufthansa is set to be the launch customer for the 777-9.
Emirates which originally planned to start flying the 777X around 2020
and has been waiting six or seven years longer than expected
has a massive order and will likely begin operation shortly after Lufthansa
given the sheer size of its commitment.
Qatar, Airways, Cathay Pacific, Etihad, they're all in the queue.
So when the GE9X finally does enter service
it's going to enter in a big way
with some of the heaviest hitters in global aviation
strapping it under their flagships.
The demand is absolutely there.
The engine just needs its airplane.
And here's a detail that really drives home
how lopsided the timing has been.
The Airbus A350 has been carrying paying passengers since 2015.
By the time the 777X and its GE9X finally enter service
currently expected around 2027
the Trent XWB will have a roughly 12-year head start in commercial operations.
12 years.
That's an entire generation of flight data
maintenance experience
and refinements that the GE9X simply hasn't been able to accumulate yet
through no fault of its own engineering.
When you're deciding whether to trust an engine
with a plan load of people over the middle of an ocean
12 years of proven service is worth an enormous amount.
There's even a wonderful irony hiding in the Airbus A380
the double-decker super jumbo.
That airplane could be ordered with engines from an outfit
called the Engine Alliance
a joint venture between GE and Pratt & Whitney.
And that engine, the GP7200
was actually built around a scaled version of the GE90 core
the very same lineage that led to the GE9X.
So GE's DNA has been flying around inside Airbus's biggest airplane for years.
These two rival engine families are more tangled together than most people realize.
Let me throw in a few more head-to-head numbers
because the details here are delicious for anyone who loves this stuff.
On weight, the GE9X comes in around 21,000 pounds
somewhere in the neighborhood of 20,000 to 21,000 pounds
depending on the exact configuration.
It's heavier than its GE90 ancestor
mostly because of that bigger fan and bigger fan case
but it's remarkably light for its colossal size
thanks to all those composites and ceramics.
The Trent XWB-97 weighs in around 16,000 to 17,000 pounds dry
so the Trent is meaningfully lighter
which makes sense given its smaller fan
even with the added weight of that complex three-shaft architecture.
On fan blade count, it's 16 for the GE9X versus 22 for the Trent XWB.
GE went for fewer, larger, more sophisticated blades.
Rolls-Royce stuck with more numerous swept titanium blades.
On bypass ratio, they're actually quite close
roughly 10 to 1 for the GE9X and around 9.6 to 1 for the Trent XWB.
Both are firmly in high bypass territory
which is exactly where you want to be for fuel efficiency and quieter operation.
On overall pressure ratio, the GE9X pulls clearly ahead at 61 to 1
versus the Trent's roughly 50 to 1.
That gap is the GE9X chasing thermodynamic efficiency through sheer compression
and on emissions, the GE9X is engineered to produce dramatically lower NOx
with GE citing emissions well below regulatory limits
and roughly half those of competing engines in its class.
Both engines are also among the quietest in their categories
which matters more and more as airports tighten noise rules every year.
There's even a logistics quirk worth mentioning.
These engines are so enormous that shipping a spare one is a genuine challenge.
The GE90 was already so big
it could only be air freighted inside an outsized cargo plane like the Antonov An-124.
The GE9X is even bigger.
During flight testing, it was so large that the only aircraft GE could find
to mount it on as a testbed was a Boeing 747-400
because the 747 had landing gear tall enough to give the giant engine enough ground clearance.
The older 747-100GE had used for previous testbeds literally couldn't fit it underneath.
When your test engine is too big for the plane that's supposed to carry it,
you know you've built something special.
Now let's look forward for a second
because neither of these engines is the end of the story.
They might be the peak of their respective philosophies
but there's already something on the horizon that could leapfrog them both.
Rolls-Royce has been developing a next generation engine called the Ultrafan
and it represents a genuine break from the past.
The Ultrafan adds a gearbox between the fan and the rest of the engine
what's called a geared turbofan
letting the fan spin slowly and efficiently while the turbine behind it spins fast.
It uses a lean burn combustor and advanced composite fan blades
and the demonstrator has a 140-inch fan
which would be even larger than the GE9X's record-setting fan.
Rolls-Royce says the Ultrafan could deliver around a 25% fuel burn improvement
over the very first Trent and around 10% over the Trent XWB itself.
Crucially, it's designed as a scalable platform
that could produce anywhere from 25,000 to 110,000 pounds of thrust
meaning it could power both narrowbodies and the biggest widebodies.
Airbus has been a partner in the program
and the A350 is often mentioned as a natural fit
so the very engine that's winning this comparison today
already has its own successor being built.
GE isn't standing still either.
The technologies pioneered on the GE9X
the ceramic matrix composites
the 3D printed parts
the high pressure ratio core
are flowing into GE's future programs
including its work on open rotor and other next generation concepts
aimed at the engines of the 2030s and beyond.
The whole industry is racing toward radically lower fuel burn and lower emissions
driven by mandates to cut carbon dramatically by 2050.
So as incredible as the GE9X and the Trent XWB are
they're really a snapshot of where propulsion stands right now
not the final word.
The engineers are already chasing the next leap
but all of that is the future.
Let's come back to the present and settle the score.
Okay, moment of truth.
Let me tally this whole thing up honestly round by round.
The GE9X takes round one size decisively.
It's the biggest engine ever built and nothing's close.
It takes round two raw thrust on the official numbers
and it owns the all-time thrust world record on top of it.
That's two clear rounds
plus the single most impressive headline stat in the entire engine world.
The Trent XWB takes round three
proven in-service efficiency
because its fuel savings are no longer theoretical.
They're a decade of real world results
and it takes round five
track record and reliability decisively
because it's actually out there flying every day
while the GE9X waits for its airplane.
That's two clear rounds
built on the most valuable thing an engine can have
trust earned in service.
And round four
technology and materials.
I called a genuine tie
because both engines are masterpieces built on opposite philosophies
and I'm not going to pretend one is clearly better when it isn't.
And round six
money and maintenance.
I also had to call a draw with a big asterisk
because the Trent XWB
9.7's durability questions in harsh climates
are balanced against the GE9X's complete lack of real world maintenance data.
Two unknowns canceling each other out
so if you're keeping score
it lands almost dead even.
Two clear rounds to GE
two clear rounds to Rolls-Royce
and two genuine draws.
And honestly
that tells you the most important thing about this entire comparison.
There is no simple clean winner here
because these two engines were never actually trying to win the same trophy.
GE set out to build a record-shattering monster
an engine so powerful and so advanced
that it could make Boeing's enormous 777X
the largest twin-engine jet ever conceived
physically possible.
By that measure
the GE9X is a triumph.
It's the most powerful and most technologically extreme
commercial engine humanity has ever created.
Rolls-Royce set out to build something different entirely
a refined, supremely efficient, reliable workhorse
that would quietly and profitably move the world for decades.
By that measure
the Trent XWB is also a triumph.
It's already proven itself across millions of flight hours
and it earned the title of the fastest-selling widebody engine in history.
So here's how I'd actually answer the question.
If you want the most powerful
most extreme
most record-breaking engine ever made
the engine that makes you go
how is that thing even real
the GE9X is your answer.
No contest.
But if you want the engine that is right now
today
quietly and efficiently and reliably carrying the world across its oceans
proven and trusted and battle-tested
it's the Trent XWB
just as clearly.
The biggest versus the most proven
the record holder versus the workhorse
Boeing's bet versus Airbus's bet
and the beautiful thing is
they're both right
because they were each answering a different question
and maybe that's the real lesson hiding inside this whole comparison.
We love to ask
which one is best
because it feels like there should be a single clean answer.
But the deeper you go into engineering
into anything really
the more you find that best
depends entirely on what you're trying to do.
GE asked
how big and powerful can we make this
and built a legend.
Rolls-Royce asked
how efficient and reliable can we make this
and built a different legend.
Neither of them was wrong.
They were just chasing different kinds of greatness
and the world of aviation is richer
for having both philosophies pushing each other
year after year
generation after generation.
The rivalry itself is what drives the whole industry forward.
Every record GE sets pushes Rolls-Royce
every efficiency milestone Rolls-Royce hits pushes GE
and the people who ultimately win are us
the passengers
flying farther
quieter
cleaner
and safer than any generation before us.
But here's the real question
and this is the one I actually want you to answer down in the comments.
When the Boeing 777X finally enters service
whenever that actually happens
and the GE9X is out there flying every single day
instead of sitting on a test stand
will it dethrone the Trent XWB
as the true king of wide-body engines?
Will all that raw power and cutting-edge technology
finally translate into real-world dominance?
Or has Rolls-Royce already built a lead so big
with so many flight hours and so much hard-won trust
that the GE9X simply can't catch up?
Drop your pick below
GE9X or Trent XWB
I read these and I want to know which side you're on
and look
if you made it all the way to the end of this one
you clearly love this stuff just as much as I do.
So do me a favor
hit that subscribe button and ring the bell
so you don't miss the next deep dive.
We've got a lot more incredible aviation stories coming
more engines
more record breakers
more of the engineering that makes flight possible.
Thanks for watching and I'll see you in the next one.