Disaster Engine! Audi 3.2L V6

The Engine Story
7 followers
21 Video Views·Sep 12, 2024
Today I'm going to show you what's inside of the Audi 3.2 V6 engine and how it works.
Now this engine is out of a 2012 Audi Q5. You can see there's a giant inspection port
right inside of the block and the upper upper oil pan.
While some people swear that this engine is pretty reliable especially for a Volkswagen or Audi,
what complicates things more is that the timing chains are located on the back side of the engine
which means that you've got to drop this engine down and remove the transmission
in order to access some of those timing components which are not the most reliable.
So we're going to tear down this engine to see just what caused it to fail.
Taking a quick look around here the front of the engine is like a normal engine with
your accessory drive, water pump up here, plastic idler pulleys over here and around the side you'll
see we have a plastic valve cover. This does have a separate cam carrier on top of an aluminum head
and then of course an aluminum magnesium block and then an upper upper upper and then a lower oil pan
and then on the top here we have a plastic intake port followed by your direct injected fuel rails
or your direct injection system and of course a plastic oil filter housing which I hate because
those leak. I'm going to start just here down by removing this valve cover but because these
torx bolt heads are so dirty I'm going to use my wife's toothbrush and just clean them up so they
don't strip out. So taking a look under the valve cover we can see that we got a hydroformed cam
shaft here with pressed on lobes. Those lobes are then going to press down on these rocker arms
underneath here which in turn are going to press down on the valve. Now I notice on these we do
have two different cam profiles which means that this has variable valve lift. Next we're going to
remove the high pressure fuel pump, probably going to be fuel everywhere. I've got gas all over my
foot. My wife's not going to sleep with me tonight but there's your high pressure fuel pump. There's
the roller cam that came out of there. To get the pump housing off I'm supposed to take out these
studs but clearly the torx on them has been stripped out. I'm going to move towards taking
off this timing cover so I'm just going to remove this heat shield here. It gives me access to this
pump. Now just remove all the 10 millimeter bolts for the timing cover. It looks super clean in there
like brand new like someone's been in here before. Now this is why this engine is such a stupid design
it's because it lives right up against the firewall here so working on anything back here
is going to be difficult even if you don't want to detach the transmission. Here you can see the
timing tensioner. It looks like these guides here on this end are intact and there's a giant cassette
inside of here that holds all the stuff together and there's a guide up here. These are all made
of plastic which is not a good thing. Let's see if I can knock these triple square bolts loose for the cams.
One thing I don't like here is that we've got a lot of interfaces where oil could leak so obviously
there's the big cover at the back here we just pulled off but there's also this interface over
here where the cam cover sits on top of the head itself and then the head sits on top of the block
over here so you've got another interface here with the bottom timing cover. This has both dual
variable valve timing on the intake and the exhaust side controlled by these two solenoids
respectively. I'm going to remove these solenoids next. Next I'm going to remove all these t30s
holding the cam caps on. I'm going to break them free first with the ratchet. There's one intake side
exhaust side. These two are almost like head bolts. It's not one, not two, but three engine hooks on this
engine. I'm telling you this engine was meant to be removed under warranty otherwise they wouldn't
have invested so much in putting hooks on. Before I remove this cam cover I got to remove this high
pressure fuel pump where these studs broke off so I'm going to use my stud removal tool here.
There we go and there you can see the lobe that the high pressure fuel pump was pushing up against
and I can remove this top half of the cam cover. You can see this camshaft has got an interesting
design with two different cam lobe profiles as well as this little track over here. The exhaust
cam profile is very simple. Now looking inside this engine it does look a little bit tarnished.
I don't think the previous owner took good care of using the proper oil so I'm just going to remove
these rockers over here. You can see it's got these hydraulic lifters on them and the good thing is
it's got these clips on here to kind of hold the rocker arm on there so they just don't fall off
unlike some Chrysler Pentastar engines. Now before I remove this passenger side head here we'll take a
minute to take a look at the direct injection system. Here you can clearly see three injectors
over here that are going to inject fuel directly down into the combustion chamber like right next
to the spark plug. That's going to give you a better combustion control however you don't have
that gasoline stream that's blowing down into the back of the valves which means that you're
going to have a lot of carbon buildup inside of here behind the valves. I'm going to go ahead and
remove this fuel rail. Now here's one thing I hate, one of these are Torx and the rest of them are
10 mil. I don't know why they couldn't use the same fastener for the same part that they're
installing. I smell gas. Tiny little T20 in here. These here are your air intake runners. They're plastic
and they bolt up directly to the head whereas this part here is your fuel rail which distributes the
fuel to the three injectors located over here on the head itself. Take a look at that intake,
how gummed up it is with carbon. Very common issue on these engines here. Look how much carbon is in
here. This one's got a little bit of moisture inside because these runners have been opened
but you can definitely tell how gummed up these are. Now in order to clean up this periodically
you're going to have to strip down the top of this engine up to this point here and send some
abrasive material down in there and suck it up back with a vacuum and hopefully that'll be enough
to loosen up all of those carbon deposits inside of there. If you have all those carbon deposits
going to cause your engine to run pretty rough and not very smooth and that's just a downside
to having direct injection down over here as opposed to in the air stream behind it where
the gasoline can act as a cleaner to clean that up naturally. I need to remove this coolant pipe over
here. Head bolts on this engine are an m12 triple square. Okay we're gonna need a longer bar. I stole
my wife's old baking pan so I can catch dripping coolant. In order to get this chain out I'm gonna
see if I can get this chain cassette thing off. This off, so this is basically the tensioner
assembly. It's actually hydraulic. Now this chain should just sit there while I pull the head off.
Well well well it looks like we've got a missing piston inside of this cylinder over here. I can
completely see the crankshaft over here and boy was this thing really hard to turn over when I was
taking off of the flywheel to get the transmission off of this thing. So here you can see is where
that piston connecting rod assembly lines up with the hole in the block here. Take a look at that.
You can just see like a big chunk of connecting rod or piston down inside of there and look at
the cylinder walls. They're all scored up. This thing must have been running with a blown piston
for a little while. Look a chunk of the block is actually missing up there. Check out the scoring
over here on this cylinder. It's so rough I can feel it right through my wife's toothbrush over
here. I also noticed that there's this rusty colored kind of coolant inside of here so I'm
wondering if coolant and oil mix causing this catastrophic failure. Well I've been staring at
this head gasket for a good 10 minutes now and my wife's probably watching me on the security camera
just looking at this thing contemplating life. Anyways I don't really see any failure on this.
Oh the story is also pretty catastrophic on the head here. This here is where the injector would
be and you can see it's all smashed up over here. It's all shiny. That means the piston contacted
the head over here. Conversely on this other side here look at how much carbon is built up on the
inside of this combustion chamber. That's not normal. It's supposed to happen. Also this is
the spark plug that was sitting here. You can see its electrode is completely smashed from whatever
happened inside of this combustion chamber. Now whatever exploded inside of here also took out
the personal crankshaft valve or pcv. See this entire housing is all busted in here. I'm going
to take that off. Alright so I'm just going to take off a couple of stuff from the top of the
engine here to make it a little bit easier to see. A couple of vacuum hoses. I got the fuel line.
Some wires here for the knock sensor. I like that the injector wiring harness is a separate piece.
That's good because you can replace it when it breaks especially being right inside of the hot
v of the engine. Look how brittle it is. Oh yeah. Oh my goodness. I'm going to really smell like gas
tonight. Just use my wiring harness removal tool to carefully remove all these wires without
damaging them. Now one thing I always dislike on many vehicles is an oil filter housing made of
plastic because they can always crack, leak and lose oil pressure or it can also leak at this
gasket over here down the back side of the engine. I prefer to keep most pressurized components made
out of metal because they have better resistance to heat wear. Now the pcv system on this engine
comprises of this entire piece of black plastic that sits in the middle of the v here. It's
basically a giant oil separator. It's going to separate any oil from the crankcase and send the
air back into the engine to get burned and obviously is a huge contributor to all that
carbon buildup in the intake valves. You can see this is the diaphragm which is what's going to be
doing the main separating of the oil. Then there's a whole bunch of baffles inside of here. You just
take out all of these bits and pieces that got damaged and oh my goodness there's a piece of
connecting rod. Look at that. Look at that. Here's a piece of the connecting rod inside of the pcv
housing. This is a real catastrophic failure. I'll probably put this on my desk as an ornament. Look
you can actually see the crankshaft down inside of there. PCV systems are not usually supposed to
see the crankshaft that easily. I'm also leaking gasoline like crazy here. This thing was probably
full. In order to get this off I'm going to remove all the t30s going around and pry this off here.
And there's what's left of the pcv system. This thing blasted a huge hole right through the pcv
valve system here. There's bits of plastic and stuff coming out from everywhere. Inside of the
engine here you got pieces of metal, chunks of plastic, more plastic. It's just full inside of
here. It's like a treasure. And there's a look under the pcv valve inside of the middle valley
of this Audi 3.2 engine. You can see it's completely obliterated. The block inside of there and the
cylinder which would have been down inside of here. And there's just bits and pieces of metal and
plastic everywhere. This is crazy. I wonder what the sump looks like. All right next up I'm going
to remove this coolant pipe going across the front of the engine here. I hate how they're making
coolant stuff out of plastic again. Coolant gets hot. Don't use plastic. All these rubber o-rings
that sit inside of here are going to leak because the plastic deforms. I'm going to remove the water
pump pulley. While I have the socket on there I might as well remove the crank pulley. By the way
without a crank bolt in here I'm not sure what you're supposed to use to rotate this engine if
there's a special tool to get to the flywheel bolts. I just have to use the starter. All right
next up I'm going to remove this water pump. At least this is pretty easy to access this being a
longitudinally mounted engine. This would be right up against the radiator area. Now that is a proper
water pump unlike the two liter engines of the Q5 that have a very faulty water pump. All right next
I'm going to remove this coolant inlet. I'm going to remove this plastic thermostat housing. Here's your
plastic thermostat. Now these plastic thermostat housings are not a very strong point in many Audi
vehicles. You can see even the housing around here is made of plastic. The only thing that's really
made of metal is the return spring in here. Look at this beautifully shaped thermostat housing.
It's just the right size. It's loosening the conventional way. There's your tensioner assembly
Next up I've got this cover here. Now it's not really a timing cover.
Yeah that's the weight for the balance shaft right there. That was so easy. It's not that heavy.
So the front half of the engine I'll clear it up here. Next I'm going to turn myself to the driver
side here and remove this part of the air intake with the injectors. Here's the air intake runners
with the fuel rail. I wonder if Audi gets sponsored by Castrol to put their name on the top of the cap.
I'm going to use my wife's toothbrush to scrub the head of these bolts here so they don't get
stripped. Now I'm going to remove all the torx bolts holding the valve cover on the driver side.
Very similar to the other side. Not the best in terms of maintenance. A little bit on the
darker side if you ask me. I'm going to remove this heat shield for the secondary air pump.
I'm going to remove two bolts here on this little air pump thing. Now I'm going to remove the tens
that hold the timing cover on. Very clean inside. Just like the other side I see the timing chain
tensioner is still intact. There's nothing broken inside here. I'm going to use this triple square
and just knock these guys out. If we can pry these gears out. I'm going to remove this timing
chain guide assembly here. It doesn't come off. Here's a stupid design. I'm trying to get that 10
mil out so we can get the heat shield off but it's blocked by the oxygen sensor which means
that you got to remove that first. I'll just pull off that header. Next I'm going to remove this
vacuum pump. Now it's driven off of the intake camshaft over here. It makes those silent but
deadly farting sounds. There's also another one of those expensive cars where they got a nice long
dipstick tube but the dipstick is sold separately. That's right there's a sensor underneath there
that you're supposed to use to tell the oil level instead of using a good old dipstick.
That could have probably prevented this engine from blowing if the owner was more responsible.
Now I'm going to bust all these T30s free that hold the cam caps on. Probably damage it if you're
doing a valve cover job. I found this little piece of debris here on this head so I'm wondering
if something inside of this head here has also catastrophically failed. Let me take off the
exhaust cam. These don't look really worn out so I don't know if this engine was really starved of
oil or not. Then I'll just take out these little roller arms here. I'm going to get this dipstick
tube off. Head bolts are M12. This one here is full of oil, this one here is full of coolant,
and this cylinder here is full of crust. It's interesting how this piston crown actually
passes the level of the head gasket. I'm going to remove this oil cooler over here.
Now this was drained of oil but so far all the coolant that came out of this thing was actually
pretty clean and not mixed with any oil. Now it's time to turn the engine on its side. Probably make
a giant mess here. Now I didn't turn this thing all the way over because there's a lot of piston
crumbs inside of there that I want to save. I'm going to go ahead and remove all these. Surprisingly
they're 10mm bolts and not stupid torx or hex or something. I need safety shoes for this. Looking
inside the oil pan you can see that we've got a good scar over there. I also found this piston
piece inside of here. Looking inside here you can see the upper oil pan also has got damage up over
here and then you can see right through the block over to the other side. Also inside of the oil
pickup tube check out all those little crumbs inside of there from when this thing exploded.
This was a pretty catastrophic explosion. Next I'm going to remove this oil pump.
Now this oil pump is driven by a rod that runs to the timing side of the engine here.
Now I'm going to remove this plastic baffle here which prevents the oil from sloshing around.
This didn't even get damaged. I was able to free that off of the oil pump drive over there.
Check out all the gunk inside of that pickup tube. Now I'm going to remove all the 10mm bolts that
hold this upper oil pan on. You can really see this entire chunk that's missing especially from this
plastic baffle that's down here. Look at all that damage inside of the block. It just chewed a line
right through the block there. It stopped right here at the gasket surface. Even the crankshaft
got chewed up over here as well. Looks like the counterweight for the other piston also got chewed
up with all the debris that was rotating around here. This here is the drive shaft that gets
powered by the timing chain which is back here for the oil pump. Now we have yet another socket type.
These connecting rod caps are e-torx 10mm. I'm going to break them free.
This thing definitely starved of oil and these ones came out of the back two pistons over here.
I'm going to try to remove these pistons kindly. There's one of them. Here's the other one. Now
this thing does not have a crank bolt. I'm going to have to be a little creative with how I rotate
this engine because I need to access the other connecting rods. I noticed this one doesn't even
have a bearing in it so I'm guessing this one spun a bearing. It was tight despite having no bearing
in there. Let's see if I can beat this out. Here's the bearing that came out of it. Let's rotate this
engine some more. All right now we're going to get these last two connecting rod bearings.
Looks like these piston tops came in contact with the head because you can see it's completely clean
here and the rest of it is all carved up. You can see the piston skirts are really worn up. I can
feel that right through my toothbrush. This thing has definitely starved of oil. Of course it has
these low tension rings that don't really have a gap in them for the oil to go back down. That's
part of a design issue. The crank bearing caps are actually integrated into this upper upper oil
pan you can see or lower block piece which forms one big structure which is good for the bottom
end strength. These are 12.10 millimeter bolts I'm going to remove. Now I'm going to zip these off.
Next up I'm going to remove all these triple squares going around the perimeter here that
hold this upper upper oil pan to the block. Remove these bolts. I wonder if I can tap out this. Oh yay
there's your plastic dipstick tube that's really useless because there's no dipstick in it. Because
the timing cover is located on the back side a lot of these gears are mounted to this upper upper
oil pan so I'm going to have to pull this off of the stand and take the rest apart down below.
I already took out the bolt for the timing cover before I put it on the stand.
We can pop off the timing cover and here we have the mess of timing chains that are in behind the
Audi 3.2 liter v6 engine. There are four chains in the system you can see these two chains here
the ones that go to the respective heads here on the driver and passenger side. I'll just remove
those those power the camshafts and of course you've got their intermediary gears that are
powered by this main chain over here that goes to the crankshaft and it's got its own tensioner
assembly over here. Now on top of all of that we've got this assembly here which is the balancer shaft
and then it's also got its tensioner mechanism over here and then additionally it powers this
gear over here which has the drive shaft that leads down to the oil pump. Quite a lot of complexity
for just a simple v6 engine which is multiplied by the fact that this is located at the transmission
site. If you have to do any service you're going to have to remove the transmission to get to any
of these guides or tensioners when they do eventually blow. This intermediary gear here
has got a triple square on it but it's kind of off-centered while the other side gear has three
little torxes on it that hold it on and they do the same thing they're both the intermediate gears
to take it to the camshafts. I'm going to knock these loose first the oil pump drive shaft popped
and I'm going to remove the secondary drive over here. One large cassette now this tensioner is
just spring loaded which is great I like this because they're not going to fail as often but
what I don't like is that all these slides here are all made of plastic. The chain is nice and
thick though. The entire slider here is all made of plastic but they are using a hydraulic and spring
loaded tensioner with the oil feed over here and we can release this chain over here and I can pop
off this guy and remove the main chain. The slides are all plastic look how easy it is to break this
it's actually pretty flexible. This one's backed by die-cast metal same thing with this one it's
backed with die-cast metal which is great. I'm going to remove this flange that held on the
oil pump gear you can see that had an oil passage inside of there to lubricate this bearing surface
that was in here there's a lot of pieces of debris inside of here. I'm going to remove this balancer
bolt remove this plate looks like it was hiding an oil passage back there I'm going to give this
oil pan a tap here and then I can take off the crankshaft and move the block off to this side
for the next segment. Now that we've disassembled the engine let's take a closer look at some of the
components that make this work starting here with the crankshaft. Now the front is where your harmonic
balancer will bolt up to and at the back here you've got the two gears for the camshaft and oil
pump drive. Now this engine suffered major catastrophic damage to the starvation of oil
around this bearing region over here you can see it is completely mangled up there's actually pieces
of bearing on here that I can't even peel off. Now this kind of failure happens when there's
major oil starvation so for example this bearing here wants to turn but there's so much heat and
friction that's built up inside of this engine it completely seizes up once this seizes up well
something's going to have to give and boom there goes your connecting rod straight through a hole
in the block. Now the main rod bearings didn't suffer too much damage it was mostly a connecting
rod thing and that's because the oil is usually fed first to the main bearing and then the
connecting rod tees off of that in order to get the oil so it's basically the last thing in the
line to get the oil so if there's any starvation issues that one's going to die first. Now one
thing you'll notice is the connecting rods don't share the same journal the way like an i6 or v8
would and that's why they have to be offsetted because this is a 90 degree v6 not a 60 degree
v6 like you'd normally see on other engines so you have to phase these apart in order for them
to balance itself properly. Now the beginning of the lubrication system starts in the oil pan where
we have this oil pickup tube here which as I've mentioned before is full of a whole bunch of junk
inside of there from the failure which means that this engine didn't just fail they actually drove
this engine after it failed allowing it to suck up all of that crap. See if I can take this oil
pump apart and see what's inside. Now this is a variable oil pump so when your rpms are a little
bit too high it's going to squeeze against that spring over there and you're going to see it's
going to change the effective volume of these little compartments inside of the vanes here
providing a different fluid flow. Now if I pop this off here you can see here's the oil pump housing
and here is the part here with the vanes these are the little vanes this thing's definitely had
some debris going through here you can see the oil has a little bit of a sparkle to it moreover
you can see them some of it is actually deposited on the bottom here. Oil from the pump is then
going to be sent through this hole over here in the upper oil pan where the oil cooler mounts to
it's going to then cool off and then sent back down over this way to the back side over here
where it's going to go into the upper upper oil pan. See there's a lot of chunks and a lot of
damage from when that connecting rod blew right through all here it's damaged now a lot of that
oil is then going to be sent straight from the bottom over here to the top directly into the
block. Now here we come to the engine block on this 3.2 engine here you could see that unfiltered
oil is then going to be sent through this oil gallery down to a main oil gallery that goes
down the middle over here on the left side look at all that damage then over here where it's
completely blown a hole right through everything and then continuing over here on the left side
now following up that left side you can see this here is where the oil filter is going to mount to
it's then going to filter out the oil and then send it back through down this hole over here
back down towards the main bearing and finally back in the middle of the v here you can see
the oil gallery where these sprayers are going to tap off of this sprayer is in the right spot
but you can see this one's all bent out of shape moving over here the sprayers don't really exist
anymore but you could see where that oil gallery used to be over here on the left side and then
finally over here you can see this one here is all mangled up but this one is definitely
spraying the cylinder walls you can see the main flaw here is you're sending unfiltered oil through
the cooler through many parts of the engine through these little oil galleries and filtering
it out all the way at the top of the back of the engine before bringing it into the main bearings
i think that's a pretty bad flaw they should probably keep the filter close to where the
oil pump is you kind of prevent a lot of that crap flowing through the oil from reaching all of these
main bearings sorry i'm gonna have to call audi out on this one because they don't even include a
proper dipstick tube for you to check it yourself you got to go through who knows what menu in order
to get the oil level from the sensor over here and in addition to that they make the oil run
through half of the engine before you can actually filter it out like i know the 3.2 engine is
supposed to be the reliable engines you're really asking for failure when you're not designing any
characteristics into this to be tolerable to low oil pressure or the lack of low oil can't be
relying on this little sensor to tell you something's wrong on the dashboard because when
this comes on it's often too late and the people who drive q5s don't really know how to read very
well either now teeing off of the main oil gallery you have these ones here that go to the head
respectively so that they can get lubricated and to feed the variable valve timing system you've
also got one that comes over here for the timing chain tensioner and then one over here for the oil
pump bearing now looking across the top of the block here you can see that's the cylinder that
blew and boy did it blow blew a cylinder liner and blew a hole in the top and the bottom and the
this is probably a higher rpm failure if you ask me now we talked earlier about the pcv system
essentially what this does is going to take crankcase pressure generated by the pistons
moving up and down and send it through that diaphragm that used to be missing over there
and a bunch of the baffles inside here before sending it out into your intake to cause carbon
buildup while we're on the block we're going to talk about the pistons or at least what's left of
them you can see on this piston here at the top there's a lot of carbon buildup it's kind of like
a sludge sort of buildup but on this side here you can see it's completely clean and that's likely
where it contacted the top of the head now what i've got an issue with is really the lower ring
over here which is your oil control ring now these two top rings over here are the compression ring
but this oil control ring is of those low tension type you can see here it's like completely blocked
up which means that as this piston is moving down it's going to try to scrape oil but there's not
much room for that oil to escape back down the inside of the piston and it's going to end up
burning oil and obviously when you burn oil eventually you're going to end up with no oil
and starve the engine of oil which is probably what happened in this case here's another normal
piston you can see it's got a corrugated section inside of here which gives it a lot of room for
oil to seep inside of there and flow back through the piston over here so this won't burn as much
oil now while the cooling system is somewhat simple there isn't a lot of robustness built
into some of the components for example the water pump is going to sit up at the front here nice and
simple and then it's going to cross over to this side over here where we have the thermostat that
sits over here that's going to allow coolant from the water pump to spread over to the back side of
the block over here to cool off the block itself now the block itself is actually pretty strongly
built although in this case it didn't really survive that's because it has a closed deck
design here which means that these areas in between the cooling jackets here are filled in
not that good for cooling supposedly better to keep these cylinder walls intact the use of plastic
on these cooling components is abundant even this thermostat is made of plastic here now that's
because these things heat cycle a lot and they can cause leakage as they warp over time now take a
look at the bottom of the cylinder head here you can see that theme with the closed deck design
kind of continued the cooling jackets around this head is actually pretty small they're not very
deep you see around here it's completely shallow there's actually not really much of a cooling
jacket here now this engine does have direct injection which is where you can see this little
port over here which is going to directly squirt fuel down into this combustion palace over here
next to the spark plug that's great because you can control the combustion better and
supposedly emissions and have more power however you will have that carbon buildup on this side
here you can see that the heads are somewhat clean not so much carbon especially when you compare it
over here to this side and as i pull out this piece here check out the wear from the chains on
this one now these chain tensioners are also oil power now the top end of this engine actually
stayed pretty clean there's not much damage inside of the cam cap bearings while there is a bit of
tarnishing from the lack of oil changes overall it's actually in pretty good shape now you can
see the oil feed where the block is going to feed the head with oil that oil is then going to make
its way to these two oil galleys over here now those two oil galleys are then going to run the
length of the head here and you can see those holes where these hydraulic lifters are going to live
the oil pressure is just going to push up on this rocker and that's what's going to push down on the
valve so you don't have any lash between the cam which is rolling around on these needle bearings
and the lifter here's a look underneath the head here from when the piston let go
and it smacked the head it damaged it pretty good and mushroomed everything sitting on top of the
head is this cam cradle it's going to take oil from over here and bring it to the two solenoids
that used to sit here to power the variable valve timing system on the intake and exhaust side
however what's most intriguing is the variable valve lift system where we have these solenoids
which have these little plungers on them they're going to kick out when activated so here's the
camshaft and you'll see that we've got this little track here where the plunger is going to engage
into and when it does engage it's going to shift from this side over to the other side so essentially
this entire thing here is going to move from one side to the other we have two cam profiles one on
this side and one on this side of course the taller one is going to open the valve more to allow more
air in at higher rpms and then the smaller one is just going to be when you're idling or driving
around town in order to select which one you want you just have to activate these solenoids
which are going to follow this little path in here and that's going to shove this over back
to the one you want depending on where you've shifted this this little roller wheel here is
either going to follow the small lobe or the larger lobe for more lift it's pretty clear that
the valves and the damaged cylinder are bent you can see right through them and that's a look at
the audi 3.2 engine and how it works now if you don't want this to happen to you make sure you
check your oil and check it often also make sure you subscribe if you want to see more videos just
like this one now if you are the engineer that designed this fake dipstick i'd like to have a
talk with you because it's responsible for many many of the engine failures that you see on this
channel
