Easy Upholstery STEP by STEP Dragon Scale Motorcycle Seat

Restore all old things
33 followers
1 Video View·Dec 5, 2025
Wanting to reupholster a seat with dragon scales for your motorcycle?
This is a video for you. Stay tuned. I will be your host, the one and only infamous Kentucky
Yankee without a doubt. Start off by making an X. It has to be perfectly square. You can use a tool
like this to assist you. Now determine your width. I want two and a half inches wide so I have this
centered. Now I'll go one and a quarter on each side. This direction needs to be smaller and I'm
going to go two inches so one here and one there. Now I'm going to connect the dots. Take a
measurement between here and here or here and here or here and here or here and here. It's all going
to be the same. Mine is one and a half inches. If your diamond is a different size this measurement
will be a different size. Next cut a strip of cardboard that width. In my case it's one and a
half inches. Mark here, here, here, and here. Then connect the dots. Now turn your stick like this.
Repeat the process. Match these lines. Copy the template. Repeat the lines. Just keep going with
it like this on both sides. Now take your template turn it this direction with your marks lining up
again and copy your template. Pay attention to which way your diamonds are. These are squattier
this direction. That's how I want them. Now you'll have to experiment. Find something round that fits
your diamonds the way you want it to fit and look. You'll make a mark from here to here.
You'll move it and make a mark from here to here. This will be the top of your scale. It's
upside down so that you can see me drawing. Next from here to here and here to here.
Now you have your first dragon scale. Now you'll carry on and make more just in a row.
You'll just keep going. You can kind of see how this pattern is working out. This is a pattern
you'll put on your fabric. The reason I did it on paper first is so you can experiment a little bit
and get your sizes right how you want them. Measure the length and width of the insert you're
going to make. I'm actually adding four inches this direction and three inches this direction.
It needs to be bigger than the insert. It will shrink as you sew it and you will need a seam
allowance. I also like to leave an allowance for how the scales are going to land on the seat.
They need to be centered perfectly if possible. Every step has to be straight and square.
Obviously to cut your pattern you can use scissors. You don't have to do it this way.
Again make sure you pay attention to which way your diamonds are going. This is squatty this way
and I actually screwed up because it needs to be squatty this direction. What I'm using is a
fabric pen to mark this up and it gives a nice detailed line. It's supposed to disappear with
heat but I haven't found that to be the case. I've been using this wax and grease remover.
You can get it in an auto body shop and it does a good job. I don't know what else would
clean it off. I'm sure some other glue gun or something. I'm using half inch scrim commonly
referred to as sew foam. It has a fabric backing on one side and then on the other side it doesn't
and this is a side wheel glue. This is a glue I'll be using. Most upholstery shops use this glue.
I'll be applying it with this Husky paint sprayer. They always say let it dry but I found
that pretty much after I spray it I can lay it down and that works best. I don't know if it's
the environment around here maybe is different than other places or what.
Now when you sew it because there's fabric on this side and fabric on this side the stitches
will pull it together and hold it in place. Sewing around the edge always makes it a lot easier
whatever you're working on and when you stop your needle always needs to be down so you can pivot
if you have to. Most upholstery shops use this T90 and you need to use polyester. That's the
most UV resistant and water resistant and all that. I'm changing the needle now because I'm
going to use a thicker thread. There's a big groove on this needle right here. It goes towards the
outside of your sewing machine. A long groove. This is a much larger needle because I'm going
to use larger thread. I think this is a number 22. If you need to know what size needle to use
with what size thread look it up on the internet. There is a chart for that. Before we start
especially on this part you better check your bobbin. Make sure she's filled up and this one
is not. This is the correct way to load your bobbin. You hold it like that. Your thread goes
that direction. Slips there underneath your little hook deal. Pull it and that's the correct way.
For the bobbin I am using the T90 thread. This is 210 thread. It's probably the most common
thickest thread used in upholstery. That being said I would prefer to use a 135 which is a little
bit smaller than this and I think it's better for this but this is what I have so this is what I'm
using. This is a typical sewing machine shank. This is a benny built shank. What I did was cut
the front off of it and round it up so that I could see the line very clearly when I sew.
This is what I'm talking about. You can see the very front of the line. I'm sewing everything
this direction first then we'll go this direction. My stitch length is four millimeter for this
and that might vary according to how big you make your scales. Wax and grease remover. This
is solvent based. They also make a water based. Now I'm going to need a pattern for the insert so
I'm going from this line one half of an inch in. This varies right now. It's thinner up here and
thicker down here but I want it all uniform so the half of an inch will actually give me a one inch
strip because I'm allowing for seam allowance. Now we'll just cut it with a razor blade.
This will be our insert pattern. You want to find the center of your pattern on the top and the
bottom. This is a notching tool. It cuts a little notch out for you. Now mark the center of your new
insert and then we'll match this with that. The pattern's all centered up now side to side up and
down. I'm just going to trace it out. Before I cut this I'm going to sew right here on this line that
I just drew. That'll lock the stitches in. Now I'm going for the ring around the seat that I want.
There's going to be a three quarter inch ring around this seat. I've allowed half an inch seam
allowance on this piece right here so I need a half of an inch here. The problem is it's actually
going to be one inch seam allowance from here to here. If you only made a half of an inch seam
allowance right here instead of a one inch seam allowance then when you went to sew your piece
you would be sewing it right here. Now if you took this off it's sewn right here. If you only had a
half of an inch you wouldn't have this extra half of an inch material here for the inside where it
folds over. Now for this side I want three quarters of an inch plus a half an inch seam allowance so
that's one and a quarter inches. I also need to mention there's going to be about a half of an
inch extra material here because when we sew it it should be sewn right here so we could measure
from here to here one and a quarter but there's a reason I'm allowing extra material here. I'll show
you what that is very soon. This is just headliner material. I'm using it like sew foam. I'll fold
these pieces in half and find the center and then mark them. I'll do the same with this part right
here. A lot of people will notch everything all the way around. I'm not really that good at this
so I just use a stapler.
The downside of the stapler of course is that you have to
take the staples out. Now where there's a curve I'm going to snip it before I staple it.
This will help it flex around the corners, sew up easier, nicer, better.
See it allows it to roll like that. All stapled up, held in place and ready to sew.
This is a magnetic guide and I have it set so it will sew it one half of an inch. The distance
between here and there is a half inch. The material will go in there like this up against that guide
and then I will start sewing. It will be nice even. Time now to do a top stitch. This is the
foot I'm using. It has a guide on it to keep it I think 3 16ths on this. By the way I did sew this
with t90 thread and I did four millimeter spacing on the stitching. The top stitch is going to be
six millimeter on the stitching. It's kind of a personal preference I think. When you're getting
close here to the end you have to get the needle just exactly in this hole right here. The very
first hole you started because I'm going to pull this thread through. Let me see if I can show you
like that. Now my needle needs to land exactly in this hole and it's hard to do when you're blind
trust me I know. Now this thread right here I need to pull in the back. So you pull your
bobbin thread and it'll pull that thread through the back. Now flip it over and tie these together.
Normally what you do when you lock a stitch in you will back the machine up. You'll keep sewing
and you'll go reverse. Sometimes I go reverse and forward and that'll lock your stitch in.
But in this case you don't want to see that. That's why we're doing it this way where you
can't see it. I do three granny knots which is probably excessive and then three more granny
knots with both sets because I don't want my stuff coming apart. It just looks like all the
other stitches you can't see it. If you didn't notice this top stitch was done with the thick
thread the 210. Now remember when we made this outside piece I said I left an extra half of an
inch on. The reason why is because now I'm going to take this right here right on this line and do
one inch and a quarter. That way if anything's distorted or out of shape or bigger or smaller
it'll all be uniform right now again before I start sewing the side on.
Done now I'll just cut it on the line and I measured it. It's a little bit less than a half
of an inch. That's why I do this because like when you do the top stitch and things like that it
shrinks things up and things get a little bit out of whack. Not serious but a little bit.
We'll set this piece aside for now. Now I'm going to take the staples out of this
right here and cut this seam right here. Just cut it straight.
I don't want to tear this seat up because this fabric because I'm going to use it as a pattern.
Steam it to make it flat then I'll take the stapler
and staple it down then we'll have a pattern. Now this piece is ready to go on the vinyl and
be traced out. I'm going to add a half of an inch on this side. This is the upper part of the seat
and then three quarters of an inch on this side. This is a lower part of the seat because I want
a little extra. I can always trim it off. I'm not making two pieces. This was two pieces. I don't
even know why but that's the way they are. It's not necessary. We'll just leave it all one piece.
Also on the ends each end needs a half of an inch where I'm going to sew it together so it
needs a seam allowance there. Another thing if you wanted to you could have cut this in half.
It just wouldn't look as good I don't think with a seam in the back. It does take a little bit more
time to put the pattern on cardboard like this but it makes it so much easier to trace and it's
more accurate. Some people don't care about that and that's okay too. Another reason a cardboard
pattern is good is if it's a common vehicle like a truck. Chevrolet trucks I have cardboard
patterns because I just reuse them. All ready to go. The first thing we'll do is sew these two
sides together with a half of an inch seam allowance. This piece is the same as this last
piece we put on. You want to find your center on everything. This part and this part and then
staple it there is what I do or you could notch it. Go around and I'm snipping it so it's
able to go around the corners easier and get it stapled up just like we did the other side and
it'll be ready to sew. Next step I'm wanting to do is put another top stitch right here.
Steaming the foam will help rejuvenate it. It'll poof back up if it needs to.
This really is some very tight closed cell foam. It's not moving much.
This is a very minor foam repair. Probably not even necessary but we'll go ahead and
patch it up a little bit. That's actually good enough.
Quarter inch stainless steel staples. I may end up taking that one out so I put it on this very edge.
I am putting the staples all the way to the outside edge just in case I have to take them
out. It won't damage anything because that's going to be cut off anyways just to get it started.
I'll keep working it all around and get it stapled up.
All stapled up now. We'll trim up the excess off of here.
By the way you don't need this many staples. I'm overkill. If I don't have to I won't cut the seam
where it's sewed. In this case I don't think I'll have to. I'm going to put a bracket over the top
of it and tighten it down. That way I don't have to worry about it separating which probably wouldn't
anyways because it's stapled up here. One last step. A little steam. I never understood this part.
Took me a long time. Finally I was talking to my buddy Max about it because I said heat expands
things. So how is steaming it going to tighten it? He said just like when we heat up metal.
When you heat it it expands. When it cools off it contracts and it normally contracts
more than normal. More than it was is what I'm saying. So then when you think about putting
clothes in the dryer if the clothes go in there and they're wet and you put them on high heat
and they're cotton they'll shrink. I'll give it a little rub down. I'm keeping a little pressure
right here. I'm gonna get sink in there. There is the finished product. I did forget to mention
steaming will get the wrinkles out. It had some wrinkles here because it's such a tight curve
but they're all gone now. If you don't think you can recover a seat like this you are wrong.
I am the one and only infamous Kentucky Yankee without a doubt at your service. Thanks for
watching. We'll see you next time.
