DIY Super Speed Boat.

Tech Boss
138 followers
4 Video Views·Dec 7, 2022
I've been building this speedboat for the last few weeks. It's a hydroplane
that's propelled by air propellers, so it's actually an airboat,
and it's designed to go as quickly as possible and maybe break
a record or two. The hull is made from PVC,
the sponsons or floats are made from wood,
and we've got some 3D printed parts, and I'm going to be showing you
exactly how I put this whole thing together step by step.
I've built a few different seacrafts on this channel before, each connected in
some way to my main interest of DIY aerospace type projects.
This seacraft is essentially a scaled up version of the hydroplane I built back
in 2018. I'm interested in the way that boats
like this use lift to plane across the surface of the water
with minimum drag. Hydroplanes are able to go way
way faster than hydrofoils, like the couple I built back in January,
as they skim along on three small contact points. Hydrofoils are inherently
draggier, as they use submerged underwater wings that usually have to
displace far more water. One famous example of an extremely fast
and successful hydroplane is Bluebird K7, a boat that set several
world records and reached a top speed of over 300 miles an hour
using a turbojet engine from a fighter jet. At such extreme speeds,
hydroplanes have to ride a very fine line and have to be
perfectly balanced to stay on the water and not take off entirely.
So I wanted to build a craft of my own to ride this line and,
with upgrades and tweaks, push towards greater and greater all-out straight
line speed. I've decided to build an airboat to see how close I can get to
the existing RC airboat record of 103 miles an hour,
set by Dan Jones in 2016. This therefore is the first episode of an
ongoing series, starting with the fundamentals such as checking to see
that the thing actually floats. In a moment we're going to put it on the
lake and see how it performs for the very first time,
but not before I show you how it was built. So
let's see how I put this whole thing together.
To get started with my design, I used Fusion 360 to flesh out my sketches and
turn them into an accurate 3D model. This was done to help me decide on the
scale of the boat and a few key choices such as what the
materials were going to be for each section of the boat. I decided
to build the sponsons of the boat, the big lifty float things at the front,
from wood, so jumped into Adobe Illustrator to design them in 2D.
These two-dimensional parts were made to be locked together using tabs and slots.
This would help to accelerate the build as I could assemble the pieces like a
big lego kit. I then cut my design on three millimeter
plywood using a laser cutter. But hold on a minute,
how did I come up with this design in the first place? I largely based this new
craft on the previous hydroplane but massively scaled up the power and
increased the dimensions a little bit. The theory with how this configuration
with the airboat propellers work is that the high center of
thrust pushes the nose down and lifts the back end out of the water.
The sponsons push back with their lift and keep everything nicely in
equilibrium. As with the smaller first hydroplane I went with a twin motor
setup with these beastie 4258 motors. They should be capable of producing
1800 watts of power and many many kilograms of thrust
each on a 6S LiPo when paired with these massive 16 inch props.
The rear prop has a more aggressive pitch than the forward one.
This is because it will be spinning in faster flowing air created by the first
prop. Right then, now we know what we're
building, onwards with the build. I used super glue to stick the sponsons
together piece by piece. The tabs and slots drawn up earlier came in very
useful here. I ordered a couple of 200 millimeter
diameter pvc pipes to use as the hull of the boat.
They're tough and waterproof but needed some reinforcement
so I made a frame for them. The pvc was a bit longer than I needed so I had to
cut it to size. To do this I wrapped some masking tape
around the tube and attacked it with a saw,
taking my time to work around bit by bit until I had cut through.
Now it was time to glue the hull together. Again I used gap filling super
glue and some accelerator to bond the pvc halves together.
Next I could glue the frame to the inside. Moving on to a slightly trickier
bit, I used some basic maths to work out
where the holes for some carbon booms needed to go
before marking some paper and laying it over the hull.
These carbon booms were secured in place with epoxy whilst another hole was cut
this time for a 30 millimeter motor pylon which was again made from carbon
fiber. I cut some mounting bracket things from
some more three millimeter ply which could hold the pylon perfectly straight
and firmly in position when all covered in some more epoxy.
Returning to the sponsons I finished them up by sheeting the tops and bottom
with balsa wood before filling any gaps with filler
and sanding it all smooth. To waterproof many of the parts on this
boat I decided to use aircraft dope which is a form of varnish that can be
applied, sanded, applied again and basically entirely seals the wood.
When I had them all nice and shiny I took a drill to the sponsons to allow
the carbon rods to pass through. In hindsight I could have planned this
all a bit better but winging it to some extent
meant I had less chance of getting the holes in the wrong places.
I used my ender 3 to print out a nose cone design that I've whipped up in
fusion. For this I experimented by using a
setting called vase mode. Vase mode prints a single outside layer of your
model to radically speed up the print time.
This nose cone only took five hours however the nose was clearly not strong
enough and had some strange warps due to cooling and
contracting during printing. This meant I reverted to printing parts
such as the tail in normal high speed modes.
The tail took around 19 hours to print. After filling gaps,
sanding and waterproofing with some more dope I could attach this part to the
hull. A simple motor mount was designed to
bolt the motors to the motor pylon. Originally I wanted to design a fancy
tilting one which could be set at different thrust angles but
I didn't really have time to develop and fix one when it inevitably exploded into
a million pieces. I made the tail skid from more plywood
and waterproofed it. In the future I might modify this part so I can attach
various different planing skids and perhaps even an experimental hybrid
hydrofoil wing that can help lift the rear out of the water
before becoming an air stabilizer. But maybe I'm getting a bit ahead of myself.
Another print later and I had a new v2 nose cone that was immensely strong.
One of the last bits to do was the servo mount and rudder. I ended up rushing the
rudder assembly a little as you'll see later on
so I will be revisiting this in a future video but for the servo all I needed to
do was to make a little bracket to hold it in place.
Before putting all the parts together in final assembly I had to paint the
hydroplane. Priming the entire thing with car body
primer I created an even base layer for the first coats
of bright blue rust-oleum paint to bite into.
A tip with this sort of thing is to take your time, do a fairly light coat at
first and then build up with successive layers.
I chose blue to capture some of that bluebird spirit and also give me an
excuse to name this thing bluebird just like
Donald Campbell's. It's a bit pretentious giving it a
name like this but I suppose it would be quite cool if this bluebird did break a
After a few layers I could seal off the paint with some automotive lacquer.
Going on to the home straight I could bolt the motors to the motor mount blocks
with some three millimeter bolts and connect the ESCs.
All of this is a bit messy for now but can be improved later on.
A temporary battery mount was glued to the internal frame and positions for two
batteries and a GPS speed unit were added with velcro.
Everything was pretty roughly taped on and velcroed in place on the inside of
the hull but there's plenty of room inside
to get in there and move things around later.
With that I could just about cram the hydroplane into my tiny hatchback
and head to the lake for a first test float.
That was close, I almost nailed in the poo there.
Are you filming? Yeah. Great, great start to the test.
The day is here, I'm going to power up the boat,
put it on the lake and yeah lovely conditions. This would only be a simple
buoyancy test with a bit of maneuvering around
just to see how the thing sat on the water. Speed was not the aim here but
of course something still had to go wrong. Time is now,
let's do it. What do you think Mike? You ready?
The plan is we're going to just stick it in the water
obviously and then we're going to just keep it pretty close to the shore so
that if it starts to sink or something that I can just jump in and get it
whereas if it's in the middle of the lake and it starts sinking
it's game over. Have you got your arm bands? I've not.
It takes a while for the propellers to stop, there's so much inertia.
I might get the wet foot here.
Why did I do that? Well it floats, that's good although I'm not sure if
it's going to stay floating, that's the only thing.
Should I take it right back out again and see if anything's leaking?
Yeah maybe. It's going to drip a bit but
there's no massive spurts of water so that's a good sign.
That's promising. Right okay, I'm excited.
It's happy to go again. The rudder doesn't work very well.
Oh the rudder's fallen off, that's probably why.
That doesn't sound good. Well it might be a bit of a short test tonight boys.
The rudder, this is the bit I was working on today and sort of rushed it so
so clearly using glue isn't a great way of
connecting a brass tube to a brass rudder.
Oh let's just check if it's actually leaking, that's a spurt.
Right make a note of that, plug that later. So obviously I'd found two issues
to fix before the next test but I still wanted to get a bit more footage for you
viewers. As the boat had tracked fairly straight previously I decided to point
the boat at the other bank and let it go just so it could get to
the other side. Right we'll just send it over there and then
get some good shots of it and then I'll do it.
Just put it back on the water. Just put it back on. However
as it turns out the boat had a mind of its own.
It's not gone towards the bank. Oh I see. Shall I just carry on?
And that was the second poor decision of the evening.
Cruising towards the other side of the lake I did get a chance to observe a
planing issue. Perhaps this was because I was in the midpoint of the planing
transition and I wasn't flooring it, only opening
the throttle up a little. But it did make me think that maybe I needed a bigger
tail skid. Reaching the other side I hoped the
boat would remain pointing towards the shore for an easy recovery.
Oh no it's going the wrong way now. It's not a good time to have had a leak as well.
It's a desperate father chasing his child.
Thank god. Where are you? I'm right here. Well that was a bit of an adventure
wasn't it? Well we've saved it. Yeah thankfully it
was pointing the right direction as I got over here so I just
powered it into the shore. All right so obviously
there's some things to improve on the boat like the rudder
and also I think there are a few issues with it planing
so the way that it was sat in the water. So we'll address that in the next video.
As mentioned we really need to address the planing issues with some mods and
come back for some further testing when we can get the thing fully out of
the water and riding the surface at increasing speeds. Despite this I'm
really pleased with the slow speed stability, the overall buoyancy and the
lift of the floats. I think this boat has some real potential moving forward
so yeah let me know in the comments if you want to see me doing more on this
boat and what your suggestions are for
improvements. Click like if you enjoy this video, if you like what I'm doing
and obviously if you're not subscribed already
do that if you'd like and thank you very much to all of my
Patreons who make things like this possible. I
honestly wouldn't have been able to buy all these different components
if it wasn't for your kind generosity. Cheers, see you on the next one!
