Building a 1500HP RB30 Stroker Engine with Jay and PRP! (RB Expert Tech Tips)
Jun 20, 2024
Building a 1500HP RB30 Stroker Engine with Jay! (Herman PRP Expert RB Tech Tips)
Special thanks to our sponsors
Real Street Performance ➤ https://www.realstreetperformance.com/
Platinum Racing Products ➤ https://www.platinumracingproducts.com/
Manley Performance ➤ http://www.manleyperformance.com/
TRC Gear ➤ https://thatracingchannel.com/
Facebook ➤ http://facebook.com/ThatRacingChannel
Instagram ➤ https://instagram.com/ThatRacingChannel
hi I'm jar I'm here with Herman from PRP
and we're assembling a new rb30 based
engine for Javier's R32
[Music]
well it's not a
JZ there's a few little tricks but it's
just another
engine there are quite a few tricks and
coming from the Jay-Z world it's uh it's
really worth applauding just how far the
a have come with the RB platform because
pound-for-pound it's hard to be a Jay-Z
in its near stock or lightly modified
form and what these guys have done over
time to
create uh the foundation to make as much
power as you can with an RB based engine
nowadays is really impressive most of
it's in the prep work well it's all in
the prep work but yeah I mean years of
evolution in the RB platform and what to
do and what not to do I still see
internet comments about people saying oh
the RBS have got oiling issues but all
that stuff's been sorted out and once
the prep work's done you know there's a
few things that we do with oil Galleries
and bungs and blocks and bits and pieces
but once that's done it's just another
engine yeah just another engine so we've
got a 90 mm stroke crank we've got a set
of uh how do you say it IRP or Italian
rods and pistons
8625 mil Pistons okay we've got some
ibeam
rods and uh we've got our integrated
main cap brace here we've got a rb30
which is a 67s variant RB it's not the
Rd which is very similar same deck
height and all the rest of it but it's
got a higher deck than the rb25 or 26 so
it allows for a bigger stroke crank and
a longer
Road pretty neat uh in terms of space
you know your deck height is how much
stroke and Rod length and compression
height how that all fits inside the
engine so this is right around 9 in of
deck where the Jay-Z is 8.6 inches of
deck so you have essentially 400,000 of
an inch to fit component which really
loans itself to making you know if you
wanted a longer Rod or a longer stroke
or a more substantial compression height
where you can fit a bigger pin height is
definitely your friend so over the
Fairly short rb26 which is 7.9 in so
you're talking numbers I don't
understand oh inches and millimeters
sorry we get stuck but you're right we
don't have a lot of deck height and with
our new block we've been able to Give It
2 mm extra deck height which has made
the world of difference when it comes to
gudgeon pin location um and where the
Piston ends up the length of the conrod
which is worlds apart from where we are
used to plotting out RB 26s and 28s but
yeah you're right that extra deck height
and being able to increase it is
monumentally better there are quite a
bit of modifications done to the block
can you go over some of the operations
that are going to allow this assembly to
work together and live well yeah so
we're used to using a much shorter crank
um well less less stroke in an rb30 so
when you go to a 3.2 it goes from 86 mm
to 90 mm and that extra throw causes you
some problems with the conrod hitting
things inside the cavity the engine
cavity so we have to go and machine some
reliefs for the conrod in the base of
the ball and then also the main oil
Gallery the conrod hits the main oil
gallery and it's all good in well to
assemble an engine and you go and put a
piston in or two pistons in however you
do it you go and turn it around a third
of a turn and all of a sudden it stops
and you've got this problem so um
Machining the block and clearancing
everything before before you go for
final build obviously it's essential but
if you already know what you're doing
before you're doing it like we've done
with this one it makes for an easier
build yeah so this uh engine was uh put
in a model and a CNC machine went and
gave just enough clearance just where it
needed it because you don't want to take
off too much material especially when
you're backing up against oil galys and
you want to take the least amount of
material out of the bottom of the scurs
because that's how you're retaining the
Piston so just done on a CNC machine uh
it's it's a a fairly um precise
operation that allows everything to fit
together well doing it with a hand
grinder much more tedious and a lot more
margin for error uh the other thing they
did was they cut a Groove in the oil
main so you have a bearing that's going
to be oiling through multiple oil inlets
so there's a larger Reservoir available
keeping oil available for the crankshaft
to keep the bearings alive which is a
pretty nice touch over just having a a
single oil inlet on the be
even pressure along the back of the
bearing coming in through multiple holes
it all help stabilize oil pressure um
and and surfacing across the bearing but
to cut that annular Groove is a little
bit tricky doing it by hand I have seen
some people with you know some medieval
Contraptions to cut annular grooves and
it and it works but having a CNC with a
ball nose cutter come in and hit it a
couple of times it's a lot quicker yeah
and we've also uh there's an increase of
the main Hardware yep so that's goes
from an M 10 stud we go out to a/ in a
lot of people also go an M12 bolt we
just go half in because the deck is also
half in from an M11 we machine it out to
a/ in stud because you can't go M11 to
M12 there's not enough thread bite okay
so you find yourself tensioning the ball
top and it'll go pop yep so going to a/
in it's just the next easiest upgrade
and it's a cheap and available stud ARP
or whatever brand you want to use so you
do the main studs and the headbolts half
in UNC fixes that problem okay and
there's going to be some order of
operations as far as fitting the girdle
to the engine block and we'll go through
that as we get the process rolling but
for now we can get the Varan in the
block get the crank in the block and
start mocking the rest of it up
[Music]
next thing we want to do is put the oil
pump on has to go on first because we
Tor down the bed plate or the brace over
the oil pump and it's really hard to
work with after that so usually I'd go
and check the oil pump alignment but now
that I've already done it realized my
Dows had to come out because I wasn't
having the movement to get my pump in
the right location why is the pump in
the right location or not in the right
location well if you main Bo tunnel B
tunnel hone your main tunnel that
position changes off the OEM so the the
original alignment Dows can no longer be
the right spot for your oil pump so
usually pull those out and then we can
go ahead and put the oil pump on this
time I'm going to use a gasket because I
know it's right already and we don't
have to pull it apart again
[Music]
okay so I just leave these a little bit
loose you only need a couple but right
now we're just going to stick in more
than a few I'll leave these ones out
because there's a crank trigger that
bolts to that one so I'm going to use
all the other
ones make sure the oil pumps still
moving and I put in my oil pump
alignment
tool I have to jiggle the pump to get it
in once that seats in we're happy we
know that's all aligned now I know
there's no tension or anything on the
main cap brace but we're talking
tent it'll be fine we can leave that oil
pump collar
on put some tension on the bolts we can
give them a final tension up later
as long as that oil pump collar still
moves we're in a good
spot beautiful we can leave that in for
now
anyway okay now we're ready for the main
cap race
[Music]
now there's a couple of main studs here
in a four-wheel drive application
there's a drive shaft that goes in the
way in the sump so what we do then is
cut about a/4 of an inch of the stud off
to make it easier to assemble the sum
what's that in millimeters it's uh about
87 or 8 mm
okay is it guess well we lost on Deck
height yeah with this metric system
stuff 9 in I'm like I know what 6 in is
but not nine
sorry main cap walk is a pretty serious
thing in an RB it happens a lot so how
do you stop the main caps walking around
it's already got a standard good that
connects all of the main caps together
which is a pretty brilliant idea from
Nissen so why cut them individually and
make a hard steel cap that has its
advantages and disadvantages and this is
not about that at the moment but um I
thought how to tie into the pan rail
without Dowling the crap out of all the
Caps so I thought why not make the
original version but tied into the pan
rails without having floating parts so
we made the first Steel in integrated
main cap brace that has it well it had
its own challenges because it kept not
wanting to settle and every time you
tension the main tunnel and cut the main
ball and then you back it all off and
measure it again it was all over the
place and it would warp and change and
it didn't want to settle so we found
that we had to settle the block with and
we tried Heat Treating we tried
everything we tried then to settle the
block by leaving it parked for 6 months
with the brace uh main cap tension do
and then you'd start to get some
consistency in the measuring of the you
know of the main ball we thought that
wasn't good enough so I went and saw a
metallurgist friend of mine and we came
up with a new composition for a ductile
cast iron which ended up forming this
brace after we machined the first uh
core plug and got that right we tried a
few different uh grades of ductile iron
we found one that was really stable it
machined really nicely uh had a nice
chip rate it was easy to treat blacken
heat treat and um you'd pull it off and
put it on back on 20 times and it was
all very consistent so we we feel we
found the right solution for this for
this engine that's cool it's pretty
interesting you know there are many
engines that had Factory uh girdles of
sorts you know you could pop the oil pan
off your Evo and some of the main caps
were tied together kind of as one
part and that all kind of gave away to
the bed plate because the bed plate puts
the main caps and the pan rail in one
piece so this is a good hybrid of a bed
plate and while we don't need it in the
Jay-Z world it sure seems like it uh
plays a role in your world should we
make it for the JayZ anyway though is it
it's JayZ I'm pretty sure it's JayZ j-z
is it Jay-Z yeah it's a b c d e f g
something something something z
z still not working yeah Z
you'll notice on this block these kind
of sinks on this pan rail have been
slightly oversized and machined in a
different spot because the pan rail
bolts were not drilled evenly on a nen
block and that happens all the time so
you kind of have to get the best of what
you can with what you have main cap
registers are skewed you have things
that don't line up you have to machine
the oil pump down or the rear main um
plate and you just have to sort of
massage things to make it work but
there's always a way to get things to
settle and sit right but um if Nissan
had the technology that they have now
with the vr38 back then which is 30
years ago it'll be a very different
looking block I'd
imagine it
wasn't what we call precise these days
so you just got to work with
it still the best sounding engine
ever checking the thrust we want to have
four or 5 th in float on the crankshaft
so just between the main cap brace and
the Fly weight we push the crank All the
Way Forward get a measurement
then all the way the other way it's
actually not too
bad we got about three th it's pretty
right but we still settle the mains and
I'll still show you how to sorry settle
the thrust so I'll still show you how to
do it because this one's probably
already been settled but it's fairly
barbaric a main cap unless it's dowed or
bed plated there's no way to align the
upper and lower thrust that's right so
you're going to mechanic align them with
sophisticated devices
absolutely we're missing the other
sophisticated device is this calibrated
um it hasn't been calibrated
by an alcoholic okay but it's pretty
good it's pretty good yeah give it a
whack and then get into the other
side and you can do it anywhere on the
crank I just prefer to do it on the
back and what you're doing there is
you're shoving the thrust face of the
crankshaft all the way back and all the
way forward and you're aligning those
bearings because the crank thrust is
true it's turned on a
lathe the block is a half and the girdle
is a half or main cap is a half and when
you hit the crank it basically lines
those halves up so your upper and lower
thrust bearing will then have an equal
amount of clearance a lot of people have
thrust problems that aren't related to
the transmission forcing on the
crankshaft or just through this process
here where those two upper and lower
halves are not in alignment with each
other and what happens if you don't
align them is you start to create heat
when the engine first starts up and
you'll create friction and you'll burn
push the oil out of the surface and all
of a sudden you start yeah munching
bearings thrust bearings and then that
thrust goes through everything else and
ruins your fresh new engine yeah lot of
money crank walk is the term we we used
for a bit is that what you guys called
it crank walk yeah CR we can run see we
agree with that crank walk finally on
something all
right five I think it's good we're good
yep so now we can finish tensioning the
main cap brace and we might check it
again when we're done I like that
another thing that you can do if you're
doing this type of work at home is
measure the endplay with the block and
the crank without the cap and then
measure the Inplay when you have the two
together and just make sure that the
same that helps tell you that you don't
have a difference between the the level
of the upper and lower thrust Berry
[Music]
[Music]
so the thrust is
good crank feels nice want to get that a
spin that's good all right spots we have
another Trick's flip the engine
over and Herman gets to show us another
RV specific thing trickery the backing
washer there's several different types
of these washers but fundamentally they
all work the same way and we just want
to make sure now that we've put our
gasket behind our oil pump we want to
make sure that this goes on and and
bases out on the collar neck of the
crank okay and stops there and doesn't
hit the oil pump which in this case
we're good there's a gap there okay so
as long as you have clearance between
the washer if you don't have clearance
between the the washer take the oil pump
back off remove the gasket remove the
gasket go silicone mhm okay so you
probably want to check this before you
put the girdle on that way you don't
have to take the girdle back off
absolutely okay clearance between the
washer and the S of the crank people ask
why that changes and I'll just address
it now niss cut those thrusts I think on
a manual machine and the position for
that thrust changes there's also
aftermarket cranks there's variables as
to why a crank snout ends up where it is
and also aftermarket collars people tidy
up the nose of it when they do a nice
Machining job not thinking that it's
going to cause you a problem later right
people of variables that can cause you
an issue there but as long as you're not
ging up the back of that washer and
cutting up the oil pump you're good okay
cool tell me something I want to know
about an RB tell me something that makes
it exciting when you guys started
messing with these engines what was the
point where you're like we're not going
to really go down the Jay-Z rabbit hole
we we like this about the RB what was
the this was it the chassis it was in
have you driven a GTR
no we need to change that okay it's a
beautiful feeling car and whether it's a
like 32 when I first got in one of them
in Japan I was buying cars and importing
them in Australia you just get in the
car and the seat just feels nice and
when you drive it it just feels like a
solid car and you get used to the engine
platform and the noise and that's just
where started now we were importing
Supras at the time as well and sure it's
a nice engine platform and car's awesome
and we were getting lots of money for it
but just to me and a lot of other people
the GTR just feels nice yeah I I would
like to drive a a 6 or 700 horsepower
R32 cuz that's the one I would own I
wouldn't I wouldn't I'd want to scratch
that itch and say like okay I like this
and look a standard car to drive with
that's 208 Kow it's it's boring it's
pretty boring I don't enjoy it well I
don't know that I the last time I drove
a dead stock usdm twin turbo super I
really enjoyed it I was like if I could
have a stock one and a modified one I'd
have two y you know just cuz then you
could have the
real the authentic personality of the
vehicle as the manufacturer put it
together and then as we made it more
powerful I've got an N1 at home and it's
it was just boring so I did a few things
I put an mtron in it I did you know some
trigger kits and coil kits and little
bits and pieces gave it a little bit
more boost and it's just a nice car to
drive and I'd call that standard yeah
yeah all right well let's um assemble
some pistons and rods and we'll load
those in and we'll be about ready to
have a completed short sounds good
[Music]
[Music]
[Music]
[Music]
[Music]
[Music]
[Music]
so these were knockins these are
knockins from Factory they're not
usually
pained um so we removed them I can't
remember the thread size but we had to
make up this particular bung to get the
right size that's not quarter pipe it's
not quarter it's a it's an overgrown
quarter okay so it's not a standard
fitting so we made them we made them
purple so people know that they're are
they're ours but yeah it's a you s a tap
we sell a tap and it's off the shelf tap
but the bung is a custom siiz bung
because it's a bigger bung than your
standed Le you got to take them out
because you have to get all the
particulate that happened through
machine so you take all your plugs out
and instead of putting Knockin plugs
back in screwing and plugs screw and
plugs now really important with
these there's a main oil gallery that
feeds the main all the mains are fed off
that oil Galley yes now if you screw
that bung in too far front or the back
you cut off the supply to the main oil
gallery on one and seven yep
smoke the crank right out of
it okay one other thing while we're
here I'm going to show you the oil
pressure bypass valve there's a there's
a oil Gallery bypass which is just a
ball on a spring in a valve that is bit
hard to get out but you get it out with
a
screwdriver and uh that lets the oil
pressure bypass the filter when it needs
to now because this is what we would
call a race engine making over 1,000
horsepower I like to cap it at 800 a
street car you might want to leave it in
and not filter all of your oil and have
a bypass for safety but if an a race
engine you're going to arguably drop the
oil very often you're going to filter
all of your oil because you can't afford
to have any metal shavings going through
your engine at any time
or the bypasses so the oil filter
doesn't blow up when it's cold uh yes
and also to not have to filter all of
the oil because in a street car you
shouldn't have to filter all of the oil
right well once the engine's established
and not making metal there isn't much
particular ever to be caught true but in
this particular application you want to
filter all of your oil all of the time
so we bung that right on plug plug got
it got it it's got to be very
complicated being Australian because you
bounce between the the metric system and
the old uh regular numbers we use here
in America metric it's always metric
unless you're building an
engine and there's some people that talk
in Horsepower and some people that talk
in kilowatts oh this thing's going to
make heaps of kilowatts with heaps of
boost heaps of kilo kilow wasps with
heaps of boost mate got it got it now
there's a bung at the back but I can't
quite get to it yet I'll get that one
when I get it off the stand we also have
some Welsh plugs what do you call them
here freeze plugs plugs to stop things
freezing well um when the person doesn't
have coolant in the engine
and it's freezing you hope that a plug
pops out before the block cracks see in
Australia nothing freezes it's not cold
enough yeah in America some places it
gets pretty gross pretty cold pretty
cold it's worth noting if you're not
going to use a screw in freeze plug you
want to make sure the freeze plug fits
extremely well because it can vibrate
out or pop out under normal
operation or if you lift the head it
will blow out and you will have a lot of
coolant
under the tires in a very short amount
of time it's one of those things that we
are far along enough in this process
that using uh coolant pressure and uh
proper bypass Val for the cooling system
if you do have a cooling system is a
smart way to not crash your car pressure
sensor pressure sensor and a pop off and
a pop off because coolant is very
slippery isn't it very slippery under
the tires slippery sucker with heaps of
boost with heaps of boost yeah what do
you call it in Australia when you've
when you recognize that you've totally
lost control of the
vehicle okay that's it this is the main
galy and it comes up and impedes the
head in two locations well in a
hydraulic head you feed in two
locations okay so an rb30 single cam
head or an rb25 non- Neo head you would
feed through both locations with a
restrictor now they come factory with
restrictors but we downsize them to stop
the amount of oil pulling in the
cylinder head but when we go for an
rb26 uh solid type setup we block one of
them usually the back one and we still
restrict the front one according to how
hard and fast the engine revs so we have
several restrictors available 1.5 1.3
1.1.9 the harder and faster the engine
revs so closer to the rb26 the smaller
the hole and the higher well and the
slower revs uh you can afford to have a
bigger restrictor in the front unless
you're sticking to hydraulic and then
you want two 1.3s for example
um the cam shaft core is smaller on the
RB so you have a faster lobe speed yep
uh do the buckets Live Well they they
live they live they could live better
okay DLC coding uh definitely helps but
you don't want to starve the top end of
oil as much as you don't want to have a
pooling of oil so yeah it's a balance
it's a balance and it's been worked out
over years but years ago the go-to was a
2.2 mm restrictor and it still just put
way too much oil in the top and you're
frying bearings down the bottom so
anywhere between you know a 1.1 and a
1.3 is fairly well happy goto and an
rb30 1.3 and an RB 26 or 28
1.1.9 if you really have an issue with
circuit racing and you want to keep the
oil out of the head but then again you
should be going dry sump at some point
yeah dry sump dry sump dry sump the
timing gear we can we can put on for a
vid cuz this engine natively had a uh uh
a cam angle sensor on the C intake cam
shop well no well technically the rb30
had a
distributor and leads oh because this
engine was for a grocery getter that's
right but the twin cam head then had a
cast a crank angle sensor that drives
off the exhaust
cam so because this block was never
designed to have a twin cam head The
Idler and tensioners don't work so we
drill a tensioner oh sorry a guide
tensioner hole here and The Idler goes
down here instead of having both guide
and tension are next to each other on an
rb26 that hole doesn't get used in the
rb30 so it basically gets relocated the
go the tensioner goes here and The Idler
goes down here and it all works do you
mind if I make a job in America we just
Ed the 2JZ and we didn't have to rely on
a repurposing a grocery getter Engine
with the correct oner head yeah that's
fair enough yeah so there's a tension a
drilling tool that we offer for the rb30
and you just flip it around one's a
drill hole and the other one's a tap
hole so you can keep it straight and not
have a CNC or a Bridge Port that's all
done we need a water pump we need some
timing gears there's a Welsh plug in the
front as well that has to go on before
the water pump and then we can put a
wood Ruff key in this one's got a single
keyway that we modified but you can use
the two half moon type keyways
MH and then that is all happy and we can
put the trigger gear on the
engine and we're pretty well set up
there right on I know that you didn't
build the engine that jaier was using in
the car at first but there are a fair
share of upgrades between that engine
and this engine can you go over what
makes this a better engine to move
forward with well I mean we still guided
um Javier and Andre in that first build
uh cuz it was U it was a new thing for
Harvey it was cutting teeth but uh they
retained an 11 mil or 12 mil stud which
isn't ideal we've gone to a half in here
it utilizes the overlay brace which we
like to rate to 1,000 horsepower and
this has got the new integrated brace
which we didn't make at the time also
this block was Sonic tested by us and
his first block I don't believe was
so we have a a system of rating the the
cylinder wall thickness and hardness to
give us a matrix on how we rate the
block and the maximum rating we ever
give a rb30 is500 horsepower due to the
deck thickness no matter how good the
balls are an rd28 is got a 12 mm deck
which is obviously a different kettle of
fish because you've got the rigidity uh
rigidity in the in the deck yeah so this
particular block got rated 1500
horsepower so it's a Block it's a known
quantity uh and now we've freshened up
with you know the new Italian rods and
pistons stuff which is not new now but
at the time that we organized this build
it was it was new and it's still awesome
gear and then we've got you know a 3.2
stroker crank uh like the other one but
it's just fresher okay we've gone to a
pro trigger now uh it's got a Billet oil
pump uh it's had a few you know upgrades
but we know what the block is it's most
important you know something can be
known it should be known so if you're
digging through cores that have uh
questionable Integrity Sonic testing is
a a really old technology of just
understanding how much material is there
that's that's that's going to have a lot
to do with how the engine lives and dies
it's just how much material is in the
cylinder walls how do the cylinder walls
keep shape under stress and how does
that deck keep shape under stress
because all that boost is trying to move
the components around and the thicker
you have in a deck and the thicker you
have in a cylinder wall the better the
components are going to keep shape so
the girdle does a good job of tying the
bottom of the engine together
unfortunately without Sonic testing you
don't know what you're getting to in the
top half of the engine which is arguably
just as or more important I think we
touched on grout filling at some point
during the build but although it's not
essential now to stop the block so much
twisting which is one of the techs that
grout filling was you know was filling a
void on uh still we have a weak cylinder
so we still grout fill them about to the
to the bottom of the higher side of the
Welsh plugs is usually just rule of
thumb it Heats oil up a little bit more
obviously the Heat's got to go somewhere
yeah cuz it can transfer yeah but it
does it has got other you know
properties which you know help absorb
noise and and um vibration in the block
and it gives you a sturdi botom in so
well I appreciate the education and the
opportunity to work on another uh well
renowned
and exciting uh turbocharge platform
that's in the same Community as the
Jay-Z so I appreciate you sharing with
me and uh get this thing back to hobby a
and get it in the car and uh get to the
track and start making some laps thank
you for the opportunity I have fun yes
sir thank you let's go
[Music]
FR keep straight
F cool

