BMW M3 COMPETITION EXHAUST UPGRADE! Remus Downpipe-Back System | SHMUSEUM VLOG 23

Compact Plug
24 followers
30 Video Views·Oct 22, 2022
Hello and welcome back to the Schmuseum where I'm back from the trip to Germany
with the Porsche Taycan. It's immediately plugged in and
charging but today we're going to be taking the BMW M3 competition
over to Motec for a new Remus exhaust. Now the trip over to Germany all the
way down to Munich and back via the Nürburgring in this
went really pretty well. Of course the first stop has been to get it plugged
back in and to charge it up with the CTEK charger
back to 100 percent but while I've been gone the guys have been getting up to a
few things here. As you can probably tell some of the
cars cleaned up. We've got some more storage racks installed
along with the hoarding on the front of them which is really quite nice.
We've also very topically over here got a banner hanging
above the race room sim about the Remus GT3 Championship 2021
Team Schmier 150 versus Team Malmedy. The six races
are going to be coming up for that so make sure to check them out and keep up
with what's going on. But today is all about this car the BMW
M3 competition the G80. A car that up to this point
I've not fully gelled with. We've only driven it about one and a half thousand
miles or so. Of course we've had it for a couple of
months now in the garage but one of the things
is the emotive connection to the car and today we're going to be heading over to
Motec. First time I've actually been to visit
the guys over there to install a new Remus exhaust to spark
things up a little bit. So we'll head over with the car
we'll show you exactly what's going to be installed on it and we'll get a
We're making this a bit of a team outing. Tom
is going to be designated driver today. Always seems to be the way whenever I'm
around so... Tom is the chauffeur, the Schmuseum
chauffeur. I'm guessing this means as usual you're
going to end up in the back. That's totally fine.
Nice relaxed drive. Let's take a listen to the start of the stock M3
competition.
So that's something we're going to be doing as well today. So new exhaust in
the car which we'll get to Motec. Some cabling as well to do some nice
features on this car as well. How's it up front Tom? I think you've
done more miles in here than I have now. I think I probably have. I don't find it
too bad. I actually find this quite a nice comfortable ride and
you guys in the back are saying that's not quite the same.
This is actually a fascinating thing. When putting it to Sport Plus
the ride back here doesn't change. It clearly only adjusts.
Well up here it's a very big difference. It's very noticeable
instantly. Which is really weird. Maybe we need to have a look to see if
we've got some transport blocks left in this because it does seem to be a thing
with your cars and suspension. Could you imagine after the GT500 had
it first in the US and then the AMG GTR Roadster
had it up front. If this had transport blocks in the back
I don't think I could ever collect a car again without checking.
It would be game over. Oh well. And we have arrived at Motec.
We have indeed. We've got Mike's lovely red M4
competition outside. So I think we will park next to that one
head inside and see what we're going to be doing. But you know what else we need
to do? What else do we need to do? A stock sound
check. We do. Yes. While it's warm. We do indeed. We need
to do this then before we'll head inside to go and take a look at the new
exhaust. It is quite windy out here but the before
upgrade versus afterwards. Let's have a quick
listen. I'll start it up. We'll have the valves closed. Then we'll have the valves
opened and we can hear all the difference. So
lastly. Start up.
Here. So valves closed. A bit more exciting.
To M2. You hear the valve opening. So that's the stock sound. It's okay. It's
a straight six engine. It sounds you know reasonably good if you
open the valve. But it's not a proper characterful sound. Which is why
we're going to head inside here now at Motec. Go see what we can do about this.
It is time to begin then. The guys at Motec are just pulling the M3 in.
Putting it next to the M135i in their new unit.
Ready to get it in the air. We're going to make a start on
the install essentially. Obviously exhaust is a big change and a few other
little things which we'll go through first. I think we're starting with them
to begin with. Just to let the exhaust cool down a little bit.
Mark will run us through those and then obviously
the exhaust system which we will show you in a minute. It's just behind this
wall so we'll run through that as well. In here then we have the lovely
looking Remus exhaust system for this car.
Which laid out like this is spectacular. There is a lot of work
into this and obviously you know better than I do exactly what we have here.
Yep so we have four parts as you can see.
Four sections of the exhaust from the rear to the front.
Here we have like the slip-on, axle, back, GPF,
back. It really depends per car, per setup how this looks.
So this is what you initially would replace if you want to keep the
OPFs or GPFs in place. Which are these lovely filters that
mute the sound. This is only this and of course we have carbon fiber
tilt pipes. So this is a stainless steel system. It's sandblasted which gives it
this really cool effect. I can tell obviously we've got the
pipework here that goes down different channels. We've got our valve control
so this gives you the variation. You can have a quiet system or you can have a
much louder system which is vital with these kind of things
to be able to have that switchable. We've then got the lovely pipework that
runs all the way through in these different sections.
We're basically taking a bit of time to let the car cool down from the
drive before pulling out the stock system.
So these are the link pipe. So this replaces
the OPFs that are here. And then normally
at this end you would have the down pipes going to the engine. We'll leave
those in. We're going to replace those. So those
will stay on this racing system because the little box at the end shows that
it's a racing system. It's going on the car and it's going to
sound considerably different. And to control everything and to make sure
that everything can work normally with all the sensors
that are now in place, we have the LiPo engineering
cabling and OPF deletors. So we have these two OPF deletors
and what they do is they go in between the cabling and the sensor
that normally controls the OPF and then tells the car that everything is fine.
So these two are going in. They're underneath the car
behind the exhaust pipe. So we have to take the exhaust off then some
heat shields and there we're going to fit those. And then this section
is a valve control CANBUS module which you're going to install and it has a
lot of nifty features. So we can control the exhaust with open,
automatic or close. We have a few system settings with
regards to the headlights which we're going to show later.
You can have cut delete in this, sound tuning,
the staging setup for the car itself can be changed. So there's all
kinds of little nifty features in this little box
and we'll show them later in the video when they're installed. So
this kind of a cool install. We're going to do this first because then we can
cool down the exhaust which is currently on the car
which is quite an impactful install because these cables have to go to the
valve and this is going to be connected at
the front on the interior. So let's do this
first, then take the original exhaust off,
put the OPF deletors in and then the new exhaust on the car and we're finished.
And get all of this installed. So shortly this will be on the car
and we'll hear how it all sounds. I think this is the perfect opportunity to make
a joke of how many guys does it take to change the exhaust on an M3.
We've got five of them under there at the moment which is good.
It's pretty much already cooled down which is good as well so obviously we
can make a start with removing bits, sort out the cabling
but all is going well so far. Not that we've done too much but we are pretty
much set up and ready to make a start. Exciting progress, come and
have a look at this. The stock exhaust is on its way off being
lowered down effectively but you can see here the various parts.
Is that ready to come out? Right now we've got the moment itself.
It's not quite as pretty as the new system
that's going in instead. This is basically one piece
all the way through obviously from the the back box here.
We've got the muffler back there, we've got OPFs, we've got the secondary cats up
towards the front and then I think this is going to slide
out and magically just like that in a second
we'll see the whole basically the whole system just coming
straight out of the car just like that. Magic. That doesn't look
anywhere nearly as nice as the new system that's going in
but that bit itself wasn't too complicated just all of the wiring that
went in before it and now we have yeah
as you can see a lot of bits of silencing
that are now going to be removed. The cool moment now though
of two systems side by side. Wow look at the difference in the back box
that's a huge huge huge change. You can see sections you see your rear
box so when the valve is open it'll bypass everything
when the valve is closed we'll go into the two small silencers
and it removes your centre silencer two OPS and two pre-cats as well.
This is going to be quite loud. With the valve open yes definitely will be louder
So we're now underneath the M3 and here we've installed the OPF deletors
and as you can maybe see on either side of the drive
shaft you can see here and there you see two sensors which measure the pressure
differences near the OPS in the standard exhaust
and with the OPF deletors we make sure that you don't get any
error messages on the dashboard so they're developed by Leip Engineering
We just make sure that they are installed on the sensors
and then we can put the heat shield back in place and continue installing the
exhaust so looking good let's get the exhaust
installed. While everything's taking place over
the other side we are here with Mike at Motec
and we're basically taking a look at some of the other things that you got
and some of the different options. Yeah first of all we need to pick some
tower pipes for the M3. Main selection gloss black, carbon
and of course if you had a normal M3 you'd have a chrome tower pipe because
the competition's come with a black tower pipe so you've got a bit of a
choice as well. Yes I hadn't really thought about that so basically
three different options you can finish them with different graphics, different
Remus logo styles as well. I work with carbon fibre, always pretty
much love carbon fibre wherever it's possible. So a gloss black diffuser like
yours is perfect. You have the carbon diffuser
you might want to go gloss black but they'll look perfect on there and we'll put the later
Remus logo on them as well so perfect. They'll be very good and then
just another stuff that we generally do really
we're an M Performance dealer as well
M Performance rear diffuser that has the crushed carbon look on the F40s
no springs and spacers you know I'm sure we'll have a conversation off camera
a lot of things we can do. It's very easy to get really led astray when you're
looking at all of the stuff here at MoTeC. Yeah there's a lot of nice stuff exactly
yeah exactly everything from wheels to intakes but
yeah so basically hopefully things are going to come
together with the car very shortly and get everything finished up. Magic the
system is now installed one thing that you notice from here by
the way is the removal of the back box that sits there looking particularly
ugly and we now have the beautiful carbon fibre
tailpipe finishes installed and the entire system that you can see
underneath here looking very very nice of course fitting in
perfectly all the brackets and everything back in place
and in a moment I guess we're going to be lowering this down and taking a first
listen to what it sounds like. It's time to start it up the exhaust is
installed and you guys are now going to listen to
yes I think we probably stood a bit too close
step back cold start most likely given it's been parked here for a while
Mark's in charge of valve control ready ready let's take a listen
now that all is completed then the car is outside and it's time
to hear how it sounds with a few blips we have the valve control of course
using the system in the BMW M3 M1 and M2 modes let's have a listen
it will be significantly louder than it was before in fact I'm just
going to stand here for a moment default setup how it is straight out of
the box
so
Tom I need your opinion of the M3 I think there's only one word
that I think there's only one word that can describe this and he's
anti-social as he is proving it is pretty and so give us another one
it's a bit anti-social
yeah it's certainly a lot louder like my fear was that the tone might be lost
but actually it's a it's a really lovely tone
it's just very loud it also matches the color
I think the color is quite loud to begin with yes yeah it's definitely very
stand out this has become the new the new M color so I think it's it's
very fitting that we now have the sound to go with it
and it looks good the pipes are the same 102 millimeter I don't think actually
I don't feel nice as you mentioned even outside it's
shaking yeah the vibrations coming off the back up
pretty and I'm not shaking just because I'm feeling the vibrations
it's to be really quite cold this evening as well so my main
curiosity now is what's this going to be like on the road what's it going to be
like at 70 miles an hour will it be really loud inside is it
livable it's valve control so the valve opens for 4 000 rpm
yes obviously it's pretty small but going to be
heavily silenced it's not going to be a massive difference there are
there are different configurations so you can of course have this with the
just axle which would be the end of the day pack everything up
experience it on the move that's what we've done as well yes
something we can do at some point test and see we should have done it before
really but before it was so quiet it would have been a waste of time
yes but i'm sure with with the guys at motec mike's obviously got these
demonstrators here so we can probably do a before test on another car at some
point then do the after we're not going to be
doing the decibel test tonight though because by the time we get back it's
going to be quite late yeah we might upset and that would be unfair for
anybody living within proximity now i think it's time for us all to
fight over who's going to drive back and let's get on the road right we're
heading out tom has the honors for the first drive i won this battle
well that's a bit different yes it's noticeably louder
i feel like this just became the team car team m3
works quite well average speed check thanks for enjoying an exhaust if we
take it out of m2 and pop it into cruise control it gets civilized and quiet and
calm it's fairly okay there's a little noise
coming through it's funny when it drops between the gears because obviously it's
just gone down a gear or it's slightly on throttle it's much
yeah for us it's not actually too bad there we go just go up into eight
manually and but this is cruising at 60 because
obviously the average speed check so at 70 it probably isn't too bad
it's nowhere near as antisocial inside whilst cruising as
certainly aware of the exhaust change though there's a lot of noise
yeah you there's no hiding from the fact that this does now have
a significant exhaust on it we're back at base
that's just the creeping idle sound and it's a lot of sound
it's actually not too bad when it's just being moved
really gently they might actually get to hear you
silence we're back in this museum and there was one thing we didn't really
discuss yet and that is the live engineering
canvas module we put under the dashboard it has a whole
range of features i want to run you through and we're going to give you a
little demo so let's touch on the features first
first of all you can control the valve of the exhaust
now fully via this button on the dashboard you can also choose to put it
on the rocker switch here and you can also set what it should be
when you start up the engine for instance do you want to
have it open or do you want to have it closed
next to that you can remove all kinds of features like
auto start stop can be removed active sound design which is the
fake exhaust noise that's come through the speakers you can switch that off
via this little box you can also the pops and bangs you know when you go into
m2 mode and then going to sport plus or sport you have all these pops and bangs
you can remove those as well if you don't like them
you can also remove the cold start you know really loud cold start which is
which is often on these new cars you can take that out as well
and then there are two really cool features next to delete
if you want to fit cutlass downpipes on this car
and then you would normally get an engine warning light on the dashboard
and this box will deal with it so then next to that those two features
first of all you have silent mode and by pressing two buttons on the
steering wheel you will be able to completely make your
car silent within just a button press so you just
press two buttons hold them for a certain amount of seconds
and your car is completely silent so you don't have pops and bangs your valve
will always be closed really nifty feature if you need that
and then the other thing is flashlight and what that is is nothing other than
you can set the lights and the way it flashes so you
pull the stalk and then it can flash like as many times as you want and
also a certain sequence so the time between flashes you can set
all this kind of stuff up so it's a bit like
what you have like when you drive in a race simulator on Le Mans 24 hours
and you press the flashlight button on your racing steering
wheel then it flashes a few times to tell the car in front of you i'm
coming get out of the way so that's what this also does really cool
and interesting feature maybe something that
not is used by everyone but if you want to use it it has this
box has that feature installed and then of course we're going to give
you a little demo now showing you how this now works with the
valve control so let's start up the car
and you can see it's closed
