Antique Rusty Shovel Restoration || Woodworking, Metalworking & Metal Etching

BM Sculptures
10 followers
5 Video ViewsยทFeb 17, 2023
Welcome to BM Sculptures. This week I'm going to be restoring and modifying this $5 shovel head
that I found on Facebook Marketplace. The shovel head may look really old and rusty but it's
actually in really good condition. There are no chips or cracks. There's not even a dent on this
thing. It seems like it's just left out in the elements to rust. Once this stubborn piece is out
it's time to start working on the handle. I'm going to be using walnut and white oak and if
you've seen any of my other videos you know I love the contrast of the dark walnut with some
lighter woods and this is no different. In order to get the thickness of the handle I glue the
boards together. Once the glue dries I scrape off the excess squeeze out and then use the
hand plane which I'm not picturing here and I get that perfectly flat so then I could throw it into
my thickness planer. Now that the walnut's all milled up I'm going to put that aside and I'm
going to work on the white oak which I'm actually going to be doing a pinstripe on this handle.
So I'm going to cut this into a very thin probably around an eighth of an inch thick
run it through the planer make sure everything's perfectly flat and then I'm good to go.
Now that the pinstripe's done I actually want to add even more to this handle so I'm going to
create a little design in this handle a white oak inlay and I think it's going to turn out
really cool you'll see here shortly kind of what I'm envisioning and what I want to do.
Now that the oak's all milled up I'm going to transfer the pattern from the walnut and then
cut it out. Now at this point you might be wondering why does he need a fancy new shovel?
Well if you see here my current shovel just does not work properly. If you see exhibit A right
here you can see that it does not cut properly it just doesn't leave a good finish on my nanners
and I love a good finish on my nanners. So now that you know why I need a new fancy
shovel let's get back to the build and cut out that white oak.
Now these glue-ups of all the different pieces and different shapes really get tricky so I
actually did this in three separate glue-ups to make sure that the first one was completely dry
and not going to move on me while I did the second and then third glue-up. Once the glue is dry I
hand plane one side and then throw it through the thickness planer to make sure that this handle is
perfectly flat and square. I then get this 45 degree angle chamfer bit and I chamfer all the
sides creating kind of a sharp angled look that I love. Oh hello there. I'm going to cut a 45 degree
angle and basically create a point on the end of this handle and then chamfer both sides to match
the other sides of the handle. Now it's time to make the front end of the handle that fits
snugly inside the metal sleeve of the shovel head.
This took a lot of different test fits and minor adjustments and sanding and little chisel work to
get it properly fit. Finally after about a couple hours of work I got a nice snug fit on the handle.
Now because the angles of the handle didn't match up that perfect circle of the shovel head handle
I basically just sanded down completely and I almost made a rounded over connection point to
make it more seamless. Now time to do the part that everybody loves sanding down the entire
thing the 240 using a block. Now if you haven't used a sanding eraser before do yourself a favor
check out the link in the description. This thing is super cheap and it saves so much sandpaper. I
love this thing. All right now let's get to some metal working here and start cleaning up this
shovel head. Okay something kind of crazy just happened. I was taking a break from polishing
and grinding the shovel kind of thinking to myself how am I going to get inside the crevice
and the little indentation with the angle grinder and sandpaper and I kid you not I'm scrolling on
Instagram just taking a break and an ad comes up of a $20 sandblaster. I'm going to go down and get
this sandblaster and see if I could just sandblast this thing instead of polishing it up the way I
normally do. My first impression is this thing is messy. You're going to be pulling sand out of your
hair for weeks after doing this without a proper sandblasting box. Now this thing worked pretty
good but I only had a four gallon air compressor and this thing is rated for like a 7 to 20 gallon
tank so I had to take breaks in between which slowed down the process. I sanded from 100 grit
up to 2,000 grit then polished on the buffing wheel to get the best shine possible. I used my
Cricut Maker to cut out my design in vinyl and then attached that to both sides of the shovel.
I wanted to match the oak pinstripe in the handle so I ended up cutting a little vinyl
slice the same diameter as that pinstripe and I put that on the shovel first.
Here it is all masked off with the vinyl and ready for metal etching.
If you want to learn more about metal etching I have an instructional video of exactly how this
works with two methods. I will put a card up top and also a link in the description for you to
check it out. Hey guys I want to take a quick second to let you know that I answer almost
every comment on my videos. If you have a question, if you want to see me do some other kind
of video let me know in the comments I will get back to you. And while you're there don't forget
to hit that like button and subscribe to keep up to date on all my newest uploads. I ended up
leaving the shovel in here for around two hours at 10 amps. Once you take it out it is best to
scrub it down with water before removing the vinyl. Now I need to oil all the metal for rust
prevention and to keep on that oiling trend I'm going to oil finish the handles as well.
I have a little bit of a problem here the handle is too long. Now I knew it was going to be long
but when I put it on the shovel head it just looks a little bit out of whack it doesn't look right.
So I'm gonna have to cut off a full 11 inches of this handle in the absolute best part of the wood
grain. I'm kicking myself for not building the entire handle around this grain. But don't worry
I am not scrapping this I have a plan in the near future for this piece. Then of course I have to
use my router to re-chamfer those edges at 45 degrees, re-sand, finish sand work, and then
refinish this entire end of the handle. Now that that's done the handle is complete it looks good
proportionally and it's time to secure the handle onto the shovel head. I'm going to use epoxy to
attach them together and then use a brass pin to really finish everything off. So remember when I
said I had a plan for this guy? Well turns out I got a mini shovel! So I'm going to basically do
the exact same thing with this little shovel and this will be the handle and I am going to have a
matching miniature shovel with the most beautiful piece of walnut as the handle.
And just like that the mini shovel is complete and we are ready for the big reveal. This was
such a fun build. I love doing restoration projects where I get to do metalworking and
woodworking. I love both of them and correlating both of those into one piece just makes me happy.
I love doing this stuff. You let me know what you think in the comments. Again I'll answer every
single comment. Let me know what you think. I hope you like this video and until next time
this is Blake from BM Sculptures.
