Restoring an Early 20th Century Antique Post Drill...

Restore all old things
33 followers
As I get older I begin to think a lot more about moving stuff out of my shop and a lot
less about moving more stuff into my shop.
So in a fit of sanity I finally realized that I just had to send this box of parts to somebody
that could and would restore a magnificent old post drill, namely Dave Van Slyke.
The rest of this story is that this project went from Cy Swan's shop to Ken Jordan's shop
to my shop and now it's being moved to Dave's shop and this time something is really going
to happen.
So this thing lived in my shop for I think it's been three years since Ken sent it home
with me and it's only been out here for about ten days and Dave's coming to life.
There's what it looks like in the box.
I would have never done this.
But I think it's about 90% certain that he's going to get it done.
Well Dave took pity on me knowing that I had at least a passing interest in how this was
going to work and he let me come out and at least see his first step, which is to unpack
the puzzle, spread it out on the dining room table and begin to set the perimeter pieces
just like at Christmas time, right Dave?
Well and the fact that this is just south of 400 pounds means that you get to help as
well, so that's fun.
Bingo!
You thought you were going to just have the camera, but nah, no.
Dave's a talented guy with a wide skill set that he's acquired over years at different
jobs and in different businesses.
He terms himself a termite because he's spent decades woodworking, including helping Ken
Jordan build his green and green masterpiece, also including building a sawmill.
So the fact that this drill came through Kenny to me and then to Dave is just a bonus for
everybody.
I'll just give it a little bit of a tap, just for fun.
So this is what, I guess you call this pinion gear, right, for driving this bed up and down.
It's missing the crank, but I have this crank off of an old cider press and it's so handsome
it's been broken and repaired so well, but it's going to be the basis of a new casting
and I'm going to have to enlarge the head because that, you can probably see, is not
going to fit.
So we're going to make it fit.
I love the shape of those little, this is early hex heads, you can see the, just look
at the different design of them than what we have for modern hex now.
Oh yeah.
Isn't that cool?
Sturdy.
Tall shoulders.
And they're just proportioned different.
Yeah, they're real, just a real tall, handsome, when they didn't care about extra materials.
Oh, I see.
That's broken off.
That's a catastrophe.
Okay.
Yeah.
That's a, that's a big remake.
Yep.
But that's okay.
That can be drilled out, right?
That's all of it.
Every bit of it.
Yeah.
Right there's a pinion.
Oh, good.
So, in fact, if I'm really clever, I could just probably pull all the way through there
to free that up and just knock that thing out.
Yeah, just knock it out.
Just have the urine peened out of it there, which is probably factory.
Yeah, probably riveted in there.
They probably set it, yeah, factory that way.
Dave loves restoring antique tools and equipment, and he's done a lot of it.
And it all looks good when he gets to the end of the project.
And he has learned over the last few years that Keith Rucker is an invaluable resource
with his YouTube channel.
He, in fact, has VintageMachinery.org.
In conjunction with Wendy Hill Foundry's YouTube channel, Dave just had a goldmine of resource
for what he was taking on.
He found on the VintageMachinery.org site an article by a man named Peter Serafan of
Boston, who had restored a drill very similar to this one and was very generous with his
knowledge.
All the knowledge sources that he ferreted out will be explained further in the second
video in this little series that's going to follow Dave deep into the weeds of this
really daunting undertaking.
An author named Orson Scott Card points out in his book, A Storyteller in Zion,
that only what we give away do we get to keep forever.
And I've grown to see the truth and the wisdom in that cryptic saying.
Because what a blessing for Sy and for Kenny and I to see Dave work so hard to bring this
old boy back from the brink.
And we still kind of had a stake in it because it came from our shops to his.
But the bonus for us is we get the satisfaction of seeing it emerge.
We get the satisfaction of seeing work done that we would have never taken time to do
and we didn't have to do the work.
So stand by for the next couple of videos that fill in the blanks on this little series
because they're going to be worth watching.
I think it's been over a month since I stopped in here and filmed Dave's initial sort of
analysis and inventory of the parts of that old drill press.
But I've been hearing good things.
He's done some casting.
He's done some machining.
He talked to a man back east who had fully documented a process.
So let's walk in, have a look at what's going on.
And the bonus point aspect of this is Ken Jordan's here.
So he's going to get to kind of keep an eye also on what's been going on with the parts
and pieces that came originally to me from him.
And I think that's just a beautiful circularity or I don't know if that's what you would call
a circularity but it sure is appropriate that Kenny gets to keep an eye on this too.
You made any headway on this Dave?
A little bit.
Show me.
Kenny, long time no see man.
How's he doing?
You keeping track of what he's doing?
He's doing good.
Well I've got a pile of parts there.
Holy smokes man.
A little different than when they came to me.
Yeah, look at that.
Wow.
So you're getting close to final assembly?
Yeah.
Yeah, I'm down to the big primal pieces now.
I'll be polishing on those and painting them.
Wow.
It wouldn't have looked like this if I would have tried it.
So far the thing I'm the most proud of is this knob.
Is that what you cast?
Yeah, that's the one that was original.
Okay, there's original.
And there's my cast.
Wow.
So you've done some casting apparently because that sure looks good.
Well this is the second time I've cast so.
No kidding.
If that counts.
I've done some casting.
You have done some casting.
Yeah, I'm real pleased how that came out.
So that's aluminum?
That is aluminum.
It has the same look as that old cast iron though.
I mean it certainly passes initial inspection.
Yeah.
And it works.
It does.
And for the purposes of this drill, the shafts and everything, this old drill is really tired.
Is it?
It lived a good life and a hard life and it worked hard.
Okay.
And when it started to fail, the guys didn't deal with issues to take care of it.
So they let it kind of go into self-destruct mode.
Failure added to failure added to failure.
Yeah, they scored some shafts with having wore out bearings.
Oh yeah, look at that.
Look at that right there, galls and stuff.
Yeah.
And this, I've got some ball bearings coming in the next couple of days.
Those are all gone.
And this whole thing, this actually, this all makes sense.
It'll make sense when I put it all together.
But this thread's on here and that's, you know, that, I guess it'd be the, let's call it the quill that lifts this up and down.
Yeah.
Well, this is a locking nut.
It was a locking nut.
It's just shiny.
You can barely make out some threads.
And you can barely make out some threads there.
So they let that roller completely out.
Long story short is for as much as I'm going to use this drill, it'll be just fine.
Oh yeah, and it's going to be gorgeous.
If it was a working drill, I'd have to replace a lot of stuff.
Okay.
Then we'd have a 1908 drill.
Yeah, that's right.
So all that to say, back to aluminum, aluminum's going to be fine for this.
Yeah.
You know, if it was a working machine that we had to count on to make a living, we wouldn't want that casting.
Yeah, but it's still hand pressure.
I mean, you're not putting a wrench on it, right?
All it's doing is bringing pressure down to that bushing and tighten that up.
And then this linkage rides on that bearing.
So that's all that's doing is just pinching that.
And then all the work's happening on that bushing with this arm here.
Okay, okay.
And then, so what you do is this just adjusts the eccentric in and out.
Is that the part that you had to build?
That's the part that we build, yeah.
Kenny machined that for me.
That's the store bought there.
That went right on.
Yep, yep, yep.
So that whole thing, that all came out of your shop?
Yeah, this is new.
And Kenny's shop.
This is new.
Wow.
To replicate what was lost somewhere along the way.
Okay.
So this table full of essentially fully restored parts and rebuilt parts and, you know,
carefully sleuthed out parts is only going to work when he puts the power to it.
You know, puts the machine in a frame and puts power to it.
And so I'm going to show you what he is pressing forward on now as far as the power supply.
And then I'm going to get a chance to do a little blacksmithing to support some of the shafts and some of those things.
But even though these parts are the meat of the matter, there's still plenty of work to do before you can put them together.
All right.
So Dave, explain to us now the propulsion and the shafts and transferring the power from that antique to that antique in order to make it work.
And you got to talk to us about these Babbitt bearings.
Sure.
So show us what you got going here.
Well, I had in my collection of gathered up parts this 1949 century repulsion start motor.
Repulsion start.
Yeah.
And I know nothing about it except to know that it's not like a modern motor.
No.
It doesn't have a capacitor.
It's the guys at the motor shop can tell you exactly what it does.
It starts up in one particular mode and then it gets to a certain RPM and shorts itself out and kicks into the next mode.
And the advantage is it's a real high torque motor.
Oh.
So the same standard 1,750 RPM?
Yeah.
This is 1,750.
Correct.
But torquey.
Yeah.
It's got real torque.
It's got good torque.
The downside is since we're going to be driving this with a flat belt drive is the bushings in this are not designed for side load.
Oh, and they don't want side pull on that shaft.
I didn't know that until I had the motor guys look it over at HPS.
And they went through and rewired some stuff and said, oh, by the way, those bushings are not designed for that.
I said, well, we're going to have to do a jack shaft.
And that's what we put together here.
So jack shaft is a term that you hear in machinery that it is a secondary shaft.
You put power onto another shaft and that is subordinate, right?
It's kind of like a slave cylinder in a brake system or something.
It's a jack shaft.
It's holding the power from the input that's putting the power in and then transferring it to the machine.
Yeah.
So all this motor has to do is provide rotary power to this.
And then all the side pull is going to be bearing off of these babbit bearings.
Babbit bearings.
Okay.
This is an old school bearing.
And you just recast the babbit on these this morning.
Yes, I did.
Did you get any video of that?
I did.
Oh, good.
That's good.
Yeah.
I'm just scraping these up and getting them settled in.
And I'm real pleased with that.
So this will couple to the motor.
The motor will drive this.
And then all of the work will happen with these bearings.
And for as little as I'm going to use it, they'll outlast me and probably my grandkids.
All right.
You're going to cut an oil groove in these?
Yes.
That's the next thing I do.
Right.
Top or bottom or both?
Both.
I'll probably, since this is such light duty, probably just top.
Yeah.
Across there.
It's a little challenging.
McMaster Car provided me with a shaft.
And since I had a lot of things to key on here, I just went with a fully keyed shaft.
So repulsion, start, induction, single phase motor.
You don't just go down to Radio Shack and buy one of those, do you?
No.
Like this one?
No, that's not too bad.
That's very good.
The bottom will look very nice.
So Babbitt is just a little harder than lead, right?
They call it white metal.
It's a lead based.
There's probably some tin in it.
You know what all the alloys are in there?
It's probably very similar to wheel weights, I'm guessing.
Yeah.
All right.
So this will key onto that.
Yes.
The keyway will fill that key slot and be machined down so you're not just grinding away at that
Babbitt liner.
I utilized a technique I saw Keith Rucker do that I thought was so brilliant.
That guy knows his stuff, doesn't he?
When he casts his stuff, he makes up these collars.
So I did the same thing.
Because imitation is, what's the phrase?
The sincerest form of flattery.
It is.
So these went on here.
And so what I did is I melted out the Babbitt from some old bearings that I had.
And that created an oversized hole, correct?
So then I got that number.
Actually, I took it in and did it on the lathe.
So these fit right in there.
Oh, they center in there.
Oh, look at that.
It does multiple things.
It's self-centering, first of all.
It creates a nice tight fit to dam up with your damming material so you don't get any spill out.
And it just makes everything basically self-aligning.
Yeah.
When you're done.
It's a little work on the lathe, which is fun work.
Sure, sure.
Yeah, and it's all said and done.
Then you just heat that stuff up.
Actually, when I did this pour, it was just like this.
And I was all dammed up.
And it comes out nearly perfect.
You put the top on there.
Yep, and that was the second pour.
The great thing about this is as soon as you're right in the middle of the bearing where you want to be, it has to fit.
And it's all said and done.
And, in fact, it does.
Because you can look at the reveals on this, and, I mean, they're spot on.
Oh, look at that.
They're just exactly what they're supposed to be.
It was never done that sweet back in the old days, right?
Oh, my God.
It recesses the babbit in a little bit because of those shoulders, but who cares because there's lots of material.
And so when the babbit cools and shrinks, you get a little bit of relief around the fit?
You know, it stays pretty tight.
Does it?
It's net-net.
And so, actually, you go in with a scraper and just do exactly what it's designed to do and get a shot of this.
But you just scrape that right out of there because you don't want it too tight.
You've got to get some oil in there because, see, a babbit bearing doesn't run on the babbit.
It runs on oil.
And so there has to be a film of oil for that to run on.
And if you don't have the oil, then it starts eating into the babbit.
So the babbit is just a support structure for the oil.
The oil is the bearing.
So this didn't have flywheel on it, which is a small thing to be missing.
The beauty shot is this way.
You're looking at the ugly end.
Oh, yeah.
Oh, yeah, yeah.
Yeah, yeah, that is the next shot.
So you might recognize this flywheel.
This is off of a blacksmith's forge.
Oh, really?
That's geared, and I don't know what that looks like.
But I think in the recesses of the cobwebs back there, I've seen something like that.
Yeah.
What I was looking at was the diameter.
Uh-huh.
What is that, 16 inches?
Yeah, and the S-curve because that's what the original was.
I see.
The original had a very similar appearance.
It had that look.
And so this was on eBay where all good things are bought for the price.
Yeah, that's right.
That's right.
But they arrive on time.
So this is not, a belt is not running on this?
No, this is just inertia.
Yeah, this is a shaft that goes overhead.
Oh.
And once things are up and running, this just keeps that energy in there and uses it literally as a flywheel.
So it was a three-quarter inch bore on that, which wasn't a big deal.
I think this is a 7-inch shaft.
I had to turn that down.
Uh-huh.
I put it all together, got a nice fit, was more proud of how everything came out.
And I put up my rollers here and put a dial indicator on it.
And it was 200 thousandths out.
And I was just shocked.
I thought it would have had to been that way before.
In the casting.
And ran that forge with a wobble on it.
Yeah, yeah, yeah, yeah.
I don't even care.
Probably RPM.
Low RPM.
So I said, well, now what am I going to do?
So I went in and turned this down smaller so that I had some wiggle room in there.
Put the dial indicator on it and just shimmed it.
Just shimmed it to true.
And I got that 200 thousandths down to probably about 6 or 8 thousandths.
That's round enough.
Yeah, for what we're doing.
Now, is that Babbitt or is that white metal?
That's actually aluminum.
That's aluminum.
When I poured that handle, I had this over here ready to go.
So I had those shims in there.
And I just wanted to lock those shims in.
And I threw some spooge in there and called it good.
It's going to be up in the air.
Nobody except a few million subscribers and you and me.
That's right.
Just a few of us know about that.
Just a few of us.
Well, this is going to be the crank to raise the bed up and down.
Okay.
And it's kind of an ugly looking thing right now.
But inside there lives a crank that came off of a cider press that I had.
And it had a 1 inch hole.
No, 3 quarter.
3 quarter square hole that I had to put these bosses on.
Oh, wait.
So did you cast this?
No, no.
This is just the pattern.
Okay.
So it lives in there.
But I made this up in wood.
Okay.
Tell us about the species.
The wood itself.
Yeah.
I like pine for stuff like this.
Yeah.
So that's a pine pattern.
So this has got lots of relief.
Yeah, so this is a cast iron handle in here.
Okay.
It lives in here.
That's actually it there.
So this mounts on the machine.
And this cranks and it raises the bed up and down work table.
Okay.
On the drill.
Make sense?
Yeah.
So it didn't have this handle.
And I like the shape of that handle.
I thought it was very cool.
So I thought, well, that's the basis for a pattern.
So I took pine and boxed this around here.
And then to make this set up here for a core, I had to think about how to do that.
So what I did is I made a silicone mold of this section, which then I poured in a urethane, which gave me this piece.
And so this piece became the guide for all the tapers and everything of what we're doing here.
And that's about a one degree taper all the way around this thing.
But I wanted this handle, when it's all done, to shoulder up right where it needs to shoulder up.
No more, no less.
And so I had to figure out a way to have that stub of taper inside this handle.
And so the way I did it is I made this little pull box.
So that's basically what we're looking at here, except I just chopped it and epoxied it on here.
Went oversized because we're going to be making a core when we do the casting on this.
So this is the same taper as that at that point that I want it to be.
So when it all gets done, Lord willing, the river don't rise, it's going to be fine.
Mr. Van Slyke is actually a fine finish carpenter by trade.
He's been a contractor here, he's done a lot of things, and he's turned his hand to restoration,
which has locked him into a lot of things that he may or may not have even seen coming.
And frankly, that's one of the appeals of learning something new,
because one new thing learns to another new thing, and first thing you know, you've actually learned something.
Thanks for watching Essential Craftsman, and keep up the good work.
