There are so many tiny, highly detailed, process specific tips like these. Methods you'll only come across every now and then when the process of throwing or trimming pottery is really broken down. In this video, I discuss what I think are five underrated pottery tips, four of which were those 'aha', 'click', moments for me, those tricks you hear that suddenly make something that you struggled with make sense.
By the way, if you have any similar tips, little tidbits that changed the way you view a specific step or process, I'd love to hear them. They can change you way you make pots drastically and I love to try and incorporate newly discovered tips from into my craft. I guess that's what we all are to some degree, we're amalgamations of the potters we've learnt from.
Thanks so much for watching!
How to wedge clay: • How to Spiral Wedge Clay How to cone smaller amounts of clay: • How to Cone Clay on the Potter's Wheel — A...
📚 • You'll find many more guides on how to centre and pull up the walls of clay here: • How to Throw a Pot — A Beginner's Guide
⏱ • Timestamps: 0:00 - Introduction 0:24 - Firstly, the condition of the clay 2:02 - The ease of centring soft clay 2:58 - Why you need to release the clay gently 3:47 - Centring the firmer clay via the push & pull method 10:10 - Another tip for centring larger lumps of clay 11:22 - What to do if the clay feels too 'sandy' 12:40 - Even a small amount of movement helps 14:09 - Clean up
*I throw using both a Rohde HMT 500 & 600 potter's wheel and fire using Rohde kilns too, the electric is a TE-200 and the gas kiln is a KG-340. ____
AI Generated·May contain errors
Video Summary
AI Generated
This guide provides five underrated tips for pottery wheel throwing to help beginners improve control and avoid common mistakes. It covers essential fundamentals—from proper wedging and continuous centering to advanced shaping techniques—ensuring more consistent, professional results and a more positive creative experience.
This week, I'll be discussing what I think are five underrated tips
when throwing pots on the wheel.
None of these were things I was initially taught, but when thinking back to when I
was first learning how to throw, these five things that I wish I was told.
Some of them might seem really obvious,
but if you are somebody learning a craft or a skill, you know
those moments where something's described to you and something clicks in your mind.
Well, these are all tips that have had that effect on me.
Bar one, but we'll get into that.
Here's the rough list, but I will of course be covering each
of these in much greater detail and amending one a tiny bit too.
But the first step, as this is really the foundation
that makes everything hereafter easier, is properly kneading and wedging the clay.
This fully blends the body, gets rid of any inconsistencies,
and pops air pockets inside. Both of which are things that will create hindrances
when you begin centering the clay and pulling up the walls.
So absolutely don't skip this process, especially if you're a beginner, as it's
likely one of those things you'll be doing for the rest of your career as a maker.
Thus, getting the fundamentals right is of paramount importance.
So the first tip I want to discuss is make sure to press in fully when lifting up.
What I mean by this is that when you first go to lift up the walls on the outside,
you really want to make sure you press your lifting finger in to create a groove all
the way around that's consistent. I don't initially think about lifting the clay up.
In fact, I'm just pressing my knuckle in from the outside to create this groove.
And the important thing is that you want this groove
to be consistent all the way around the circumference.
I press in and keep that knuckle held in place until I can see
and feel the indent all the way around until the entirety of that circle
of clay has passed through my grip, and only thereafter do I begin lifting up.
If, on the other hand, you pinch and lift immediately,
you end up indenting one side of the walls, but not the other.
This not only creates more drastic throwing rings in the pot you're making,
but depending on how quickly you're spinning the wheel
or how firmly you're squeezing your hands together,
you can actually create an undulation in the pot simply by rushing the process
and not creating this careful groove initially.
Before I begin lifting up from the inside, my fingers are pressing out where
that bump is, and then from the outside, I lift this bulge of clay up.
I know this sounds really basic, but I wasn't taught
this when I first started to learn, and even when I taught evening classes,
I'd see beginners trying to rush this initial process.
They wouldn't set the groundwork by creating that intentional groove.
Instead, they're just pinching pull up quickly, which,
if not done properly, doesn't move the clay up all too much.
It also means you're not pressing in material around the base,
which you can then lift into the walls,
and you end up pinching and exerting pressure the whole way up,
when in fact you can lift just by creating this groove around the bottom,
which means I am applying quite a lot of pressure initially. After which,
once that groove has been made, you don't squeeze your hands any further.
You just lift whilst keeping them held in that position.
This means you aren't pinching or squeezing the clay the entire way up,
meaning there's less that can go wrong.
As if your hands do slip, as you're not squeezing them together really firmly,
they don't fling off and hit other parts of the pot, potentially destroying it,
which again is something you often see beginners doing,
especially as the hands get close to the rim. You keep pinching
and you get closer to the rim, and all of a sudden there's nowhere to go.
So instead of just gently releasing your hands as you get to the top,
you pinch through the rim as you get to the top of your lift, distorting the rim
and creating an undulation, a wavering top, which you then have to correct.
So in short, much of lifting up the clay is about creating this initial groove
and the bump above it. Yes, you are applying pressure to do this, but thereafter,
as I lift this section up, I'm not continually pinching the walls as I lift.
Instead, my fingertips and knuckle or sponge on the outside just stay
in these positions, and then they're raised up together.
So, to sum this first tip up, press in slowly and gradually at the bottom
and create a distinct groove that travels all the way around before you lift up.
Now the second tip isn't so much of a practical one;
rather, it's a bit more of a philosophical take.
And that's simply knowing when it's worth calling it a day.
There have been so many times throughout my career as a potter so far where I've
encountered a particular shape that I just mess up again and again and again.
Normally during the throwing process, and it does become extremely frustrating.
You start beating yourself up about it, taking the failed clay,
wedging it up, and trying again and again and again.
And there's one particular shape in my career, which were these small
leaning back jugs I was making during my apprenticeship at Meisel Pottery.
They were an absolute nightmare to get right.
And the pots you see here weren't made during
my first throwing session, learning this shape.
Rather, this is a couple of weeks down the line after a handful of making sessions.
Sometimes there'd be one or two to show, or other times I'd have
to trash an entire board's worth as the shapes weren't right.
So if you find yourself in the situation where you're becoming frustrated,
you keep ruining pots and you're becoming angrier and angrier with yourself.
Just stop and either make a shape you're much more comfortable with,
which for me are just mugs or bowls, shapes that I'm really familiar
with and can almost make with my eyes closed, or I just pivot entirely
and do something productive like tidying up the workshop or doing some organising.
Anything essentially that isn't failure.
Okay. The next tip is to slow down
and to check your piece during the throwing process.
You may think that you can only centre a pot at the very beginning,
but the truth is there's a number of times when making a pot from beginning to end
that you can check it and centre it to make sure the walls are spinning evenly.
So obviously you can centre the clay when it's in this shape,
but often during the opening up process, beginners will do this step unevenly.
And even if the initial lump was perfectly centred,
there might be an undulation in it now.
But the good thing is you can re-centre the clay when it's in this shape, which I
do by wrapping my hands around the spinning clay, clasping them tight, and letting
the clay spin through these new rigid handholds that are keeping it centred.
So if you ever do find that your opened up piece of clay is off centre,
this is easy to check. By the way, if you see the walls undulating like so,
sort of jittering in place instead of gliding perfectly on centre,
wet your hands and the spinning clay. Clasp your left hand around the part
that's closest to you and wrap your right hand around the outside.
Tense and squeeze your hands and slightly collar in the shape, but most importantly,
focus on simply keeping those hands stable and not just following along
and bouncing around with the undulation that was in the clay.
You can do it on the other side too, and generally the way I approach
this changes a lot depending on the shape of the pot I'm working on.
But that isn't the only moment I can recenter the pot.
I can do it again after the first pull.
Then after the second, the third.
The fourth.
And even the fifth.
And I'm essentially doing the same thing with the chamois leather at the very end.
So just remember, centering is something you can
do at almost every stage during the throwing process, not just the beginning.
The next tip is to spin the wheel faster than you think for less throwing rings.
This holds true, but really it needs the amendment,
which is the importance of the consistency in your throwing rings.
This is a really good way to tell whether you're throwing consistently or not.
Essentially, there's a perfect balance between the rate at which you move
your hands up and the wheel speed that leaves you with a very flush,
clean surface with minimal throwing rings.
They should look soft and quite close together, like you can see here,
traveling all the way more or less from bottom to top.
If the rings look the same, it means you've moved your hands up at a good even rate,
which generally means the walls of your pot will be even too in cross section.
Now, if you are going for intense throwing rings,
then this is an entirely different story. But if you aren't,
and you find that your throwing rings have more space between them and are deeper,
then it means you're moving your hands up the walls of clay too quickly.
At the same time, you don't want to move too slowly, as if you spend too much time
in one place, you can create a thin patch, thus weakening the walls,
especially if you do it towards the bottom, as there's much more weight above it.
But going back to what I initially wrote,
which was spin the wheel faster for less throwing rings.
This takes into account you aren't raising your hands up too quickly,
as even if you spin the wheel really fast,
if you're lifting your hands up very rapidly too, then of course
the throwing rings will be very intense, and they can look something like this.
The thing is, in terms of cross section, the walls on this are thick
and thin and thick and thin all the way up, and this disparity,
if not controlled or corrected, typically tends to just get worse.
Unless, of course, this is the aesthetic you're going for.
But still, the most important thing about lifting up is spinning
the wheel relatively quickly with moving your hands up at a constant rate.
As if you don't, this is what happens. In this instance, I initially threw slowly,
then quickly, then I lingered in one spot, and then I raced off the top.
And as you can see, this is left a completely uneven surface,
simply due to the rate at which I moved my hands up the piece.
If you throw altering the position of your hands into the mix too,
you can be left with really wonky walls, and thin patches can easily develop,
which end up buckling and causing the pot to collapse. So the rate at which you move
your hands and the wheel speed should really remain consistent as you pull.
As as soon as you begin changing wheel speed, hand position,
and the rate at which you move your hands up during the pulling process,
then you'll end up encountering difficulties like these.
And the final tip, and this is something I talk about quite a lot,
is press out against a rib or a kidney.
Dictate where you want the profile of the pot to be, not the other way around.
So much of learning how to make pots is about learning how to be the one in control
of the clay. When you're first learning it, often feels the other way around.
The pots you make are different each time as the process itself is a struggle.
But with time, you learn to be the one who dictates what the clay does
and what the final form is. And one thing that really helps is being able
to correctly define the shape without accidentally deforming the pot itself.
Thus, when it comes time to scrape clean the walls of the pot and to really shape
the vessel, instead of just jamming the piece of metal into the clay,
which is something I see lots of beginners do, instead you want
to hold whatever type of kidney or rib you're using just hovering over
the clay where you want the profile of the pot to be.
Then you push from the inside out against this edge.
I also tend to tilt the rib forward slightly as this creates
a smaller point of contact which scrapes away the slip more efficiently.
Either way, the rib itself stays relatively stable,
but I move it up slightly as the pot gets taller,
pressing out the entire time instead of forcing the rib against the clay.
This puts far less stress on the pot as you're exerting far less force on the object
as a whole. And after a pass or two, you're left with this lovely smooth surface.
I've also found that it distorts the overall shape less doing it this way,
as you're essentially pressing the walls out precisely where they need to be.
This is a technique I use whenever I'm shaping pots.
The outside hand and that metal ledge is kept steady whilst
the clay from the inside is pressed out against it,
and it works especially well on thinly walled pieces towards the rim,
where typically the vessel becomes weaker as there's just less clay supporting it.
This isn't to say that I don't use the kidney the other way around,
say pressing it into a piece to remove slip.
I still do do that, but it's really shape dependent.
The thickness of the walls also plays a large part too, as obviously
with a sturdy pot you can be a bit more aggressive with the kidney from the outside,
but typically even with bigger pieces I hold the kidney steady
and I press out against it.
I find with smaller pieces and those with narrow necks or even spouts,
I work the other way around.
But for day-to-day pieces such as bowls, mugs, and vases,
I never tidy up the walls by just pressing the metal in, like you can see here.
Instead, a majority of the work is done by pressing the wall out against the tool.
By the way, I lean towards using sharp metal kidneys
and ribs as they're much sharper and scrape away the slip more efficiently.
But they come with the downside of being obviously sharper,
which means if you make a mistake, it tends to be worse.
Now here's what happens if you do it the other way round with a piece like this.
Instead of trying to shape it by pressing out,
I'm going to be pushing in with the kidney.
Immediately I feel the wall bending inward.
As with the amount of force needed to scrape away the slip,
I actually have to press in really hard.
Obviously at the same time I have to press out to counter this force,
and as a result I'm pressing both out with my fingertips and I'm pressing
in with the metal tool. Yes, it does leave me with a very clean surface,
but the issue is the shape itself begins to change as the clay can't move down
or in or out, so it has to go up. Thus in scraping clean the outer surface,
I've ended up with a pot that's taller than I intended.
I should also say if you're trying to shape by pressing the metal in and the walls
of your pot are as thin as this, there's a very considerable chance
that the sharp edge of the tool you're using will catch on the spinning clay,
completely destroying the pot. So to recap, when you are shaping, press
the clay out from the inside against the edge of the kidney or rib you're using.
The tool itself shouldn't be pressed inward, but you can raise it up if needs be.
If the pot gets too tall, following the specific profile you're after.
So I hope you found those five underrated tips helpful.
Let me know if you did, and also if you have any of your own like this,
I'd love to hear them. That's all for this week.
Thank you so much for watching if you've made it to the end,
and as always, I'll see you next time.