Carpenter Builds a Bench/TV Stand from a Single Plank | New Build Season 7 Part 7

Inside Home
23 followers
#Craftsmanship #WoodWorking #JapaneseCraftsmanship #Carpenter #JapaneseCarpenter #JapaneseSkill #DIY
#DIYwoodworking #JapaneseArchitecture #Architecture #TVStand #Bench
AI Generated·May contain errors
Video Summary
AI GeneratedShayan constructs a massive, 5.5-meter wall-to-wall built-in counter made of ash. The multi-purpose unit features a central TV stand flanked by benches or tables. Because the client requested a single-piece countertop, Shayan builds the entire structure on-site, utilizing precise scribing and custom fitting to ensure a seamless integration with the room's architecture.
Hello, Shayan here. Today I'm building a counter
with a TV stand in the middle and a bench or a
table on each side. It's multi-purpose
and the whole thing runs wall to wall. Since it spans
the whole room, it's easily over 5.5 meters long.
Let's get started. I think this stretch
of videos will all be about building interior pieces out of ash.
This one is ash again.
Since it runs wall to wall, it's long.
I've never built a TV stand or a counter this long before.
It's built in furniture.
What's interesting about
it, what makes it unique,
is that it's all one
piece. I had a woodworking shop make the countertop.
Normally, in a case like this,
I'd build three separate units and fit them neatly into the house.
The only difference is whether the counter runs as one plank or not.
If the countertop could have seams,
I could just build 2 or 3 units and set them in place.
Only when someone insists on it being one piece,
does the carpenter struggle through building it in on site.
Honestly, it's hard work and it's heavy.
But when it's done, I'm sure it'll be something really worth having.
Circular saws
are battery
powered
these days,
which is nice.
But this one just stops all of a sudden.
Even when 95% drained, it keeps spinning at full power.
So I think it'll make the cut and then it just shuts off.
I don't check the battery level every single time
so I end up using it until it dies.
Since this is a built-in made on site,
I get nervous making templates
or taking measurements too casually.
Especially since the material can't be replaced.
So even though it's heavy,
I have no choice but to set it in place once.
Then, I take my measurements from the actual site and mark it.
I've never once changed this approach.
I suppose it all comes down to not being confident about it.
But fitting
it against
the real
thing is the
surest way.
As for the shape, there's a bottom panel,
the vertical panels stand on it and the top
goes on last.
Fastening the vertical panels to the bottom panel is a bit tricky,
so this time I'm setting them into dados cut
into the bottom panel to the exact size of each
vertical panel.
I use offcuts of the actual material and carefully trace each one, make
kerf cuts and use a groove cutter like this.
Then I chisel it out to finish it.
Since the material is ash,
being off by even a little can make it too loose or too tight,
which makes it tough to work with.
So I check the fit every time as I go.
I cut
and
plane
each
piece
one by
one. I
go over
them
all
with a
hand
plane,
then finish with sandpaper on a sander.
It'll be coated with a finish. Hardwoods especially
are prone to tear out, and if any is left,
the sheen shifts here and there.
That shifting sheen can be part of the charm
but for the finish to go on evenly without blotches,
sanding is a must.
Now I install
the bottom panel.
I think the bottom panel is fairly easy
because I've already built a base frame
with a toe kick along the front that's
the same height as the baseboard around the room.
I put glue on top of the frame and set the bottom panel on it.
I can drive screws firmly into the frame along three sides
and at the dados where the vertical panels go.
So fastening the bottom panel itself is easy.
Ideally, the side panels
and countertop would go in as one assembled unit.
But it won't fit, which is exactly why I build it in place.
That's the tricky part of built-ins.
Now that the bottom panel is in,
I put boards on the wall in front of me
before standing up the vertical panels.
That's the back wall of the cubbies.
I use cedar offcuts from the soffit and the rooms.
Eh, but you're supposed to be a carpenter, aren't you?
I'm going to play Daigo again.
I'm about to go to the studio.
This summer was really hot.
I sweat buckets so that part of summer is always tough.
All I can do is keep moving forward one board at a time.
I just keep at it until I can finally say, there, it's done.
I mark the
vertical
panels
so that they
fit snugly
where
they go
and stand all eight of them up first.
But I haven't cut them to height yet.
First, I cut only the two at the ends.
Then I take the heights of the ones in between.
Of course, cutting them all to the same size should work.
But I make sure to fit things to the actual size.
So, I set the two end heights,
stretch a string line and take the heights of the six in between.
That way, even if things are off by 2mm or so,
the top still runs perfectly straight.
That's the basic rule for built-ins on site.
I
fastened
the
vertical
panels.
The ends were easy since I could drive screws in from above.
For the ones in between, the screws go into the wall at the back.
For the dado joints, I rely on glue to hold them.
I spread strong glue on the bottom of each dado.
At the front, I clamp them down to the bottom panel.
That's how I stand up the six panels in between.
The middle
section is the TV
stand, which
is the main part
of the counter.
So I add one more shelf there.
There's no way I can build a shelf in such a tight spot.
So I make it in an H shape first.
Then I attach it to the bottom panel in that shape.
The screw heads always end up showing.
Even down low where you'd think nobody would see them,
they catch the light and stand out.
So I filled
them
with wooden
plugs.
The TV stand section also goes together with glue and screws.
This is urethane glue and it really sticks.
I use it wherever something absolutely can't come apart.
When I used it years ago,
I was so impressed that I said it sticks to anything except water
Someone commented that was a bit of an exaggeration.
But honestly, it sticks so well. It's impressive.
The squeeze out just
turns into spongy foam.
So I take it off with a chisel or a utility knife.
And the surface is clean again.
It's handy glue.
With the vertical
panels in,
it's finally time
for the countertop.
It's only a little wider than the bottom panel but it really is heavy.
Same as before, I set it here once and take the measurements.
Now I transfer the measurements to the countertop,
which is called scribing.
This top lines up with the bottom of the window frame.
Like a bay window,
it doubles as the windowsill and spans the full width.
In the middle, I cut it to fit around the wall.
The window frames are different widths on the right and left.
So, in a case like this, I make a template and trace with it.
If I took measurements with a square and got it wrong by 15 mm,
that'd be a disaster.
It happens once in a while.
Whether I measured from the outside or the inside edge of the square
makes a 15mm difference.
Even when I'm careful, I sometimes get mixed up.
But if I make a template
like this, I can follow the same measurements on both sides,
so there's almost no chance of
a mistake.
Now I cut the countertop.
Where it meets the wall,
I notch it a little oversized,
and only the part at the window frame needs to fit tight.
Since it only has to fit against the window frame it's simple enough
but fitting a countertop's
notch around something that sticks out
and fitting its protruding part into a recess
are two very different things.
A protruding part can be planed so if I plane it carefully
it'll
definitely
fit tight.
I finished the
countertop
with the
sander too.
It ended up
thinner than I expected so for the edges I go
with a standard chamfer just a bit on the large side.
If it were a little thicker,
I could do a bull nose with a bigger rounded profile,
but a larger
chamfer
is plenty.
Now that the
countertop
is cut,
I can finally install it.
Same as before, the screws go into the wall and the rest is glued.
Glue needs pressure to work, but this shape makes it easy to clamp,
so I can rely on strong glue here.
At first, I plan to put in about two screws per spot
and hide them with wooden plugs,
but the countertop really is better without them.
If I used plugs, I was going to have fun with different shapes,
but it looks
cleaner
without them.
Next, I run window jamb extensions around above the countertop.
It's rare to have a counter on the bottom
and jamb extensions on just three sides.
Scribing them to the countertop
and getting the measurements right is especially tricky.
They reach
the ceiling,
fill the
full width
and have to
fit against
the counter.
Compression rods are so handy here.
They hold everything tight. I wonder how many tools they're
worth. Now the 5.5
meter TV stand is done.
It's long and the biggest
I've ever made. With this
length you could even fit three TVs of any size on here.
Put a TV in the middle and use the rest
It's a great piece. That's all for today. Thanks for watching.
