Geologists Just Found Out What Egypt’s Serapeum Boxes Actually Are

Archaeology Explained
5 followers
Nov 15, 2026 #archaeology #history
AI Generated·May contain errors
Video Summary
AI GeneratedThe Serapeum of Saqqara is an ancient Egyptian underground complex containing 24 massive granite sarcophagi for the sacred Apis bulls. Discovered in 1851, the site is a marvel of ancient engineering, showcasing extreme precision in stone-cutting and immense logistical coordination in transporting 60-ton monoliths from Aswan to the Saqqara Plateau.
Granite boxes of around 40 tons,
each one cut from a single block of stone. Lids of around 25
tons more, laid on top with joins
so tight that a sheet of paper struggles to slip in.
24 chambers carved into the bedrock beneath the desert,
reached by corridors barely wider
than the boxes they hold.
Stone from quarries roughly 800 kilometers
Put the box and its lid together
and you are looking at as much as 60 tons of hard rock,
or more upriver.
hollowed out, polished, and slid into a tunnel underground.
This is the Serapeum of Saqqara,
and it is one of the most difficult pieces of
ancient engineering on record to explain step by step.
The usual story is short. The boxes held sacred bulls.
The bulls belonged to a god, and Egyptian craftsmen made them.
Each of those statements is broadly true,
but none of them tells you how a block of granite
the size of a small room was cut free from a riverbank quarry,
floated hundreds of kilometers
downstream, dragged across the desert,
lowered below ground, hollowed out without cracking,
and finished to surfaces that still catch the light like still water.
That gap between what
What we know happened and what we can actually reconstruct
is where this story lives.
Geologists, engineers
and archaeologists have spent decades working inside it.
What they have found is stranger and more impressive
than either the textbook summary or the internet legends.
Stay with me, because the answer to what these boxes really are
starts with a man digging for a statue in the sand.
In the autumn of 1850, a young French scholar named Auguste Mariette
is in Egypt on a modest assignment.
He has been sent to buy Coptic
and Syriac manuscripts for a museum in Paris.
The manuscript dealers are slow,
the monasteries are cautious, and Mariette is restless.
He wanders out to Saqqara,
the vast burial plateau west of the old capital of Memphis,
a place of collapsed pyramids,
wind-scoured mud brick and drifting sand.
There, sticking out of a dune, he notices the head of a sphinx.
It is not a remarkable object on its own.
Saqqara is littered with fragments.
But Mariette has read the Greek geographer Strabo,
who visited Egypt around 2000 years ago
and described a temple of Serapis near Memphis,
built in a place so sandy that the wind piled
dunes over an avenue of sphinxes, some buried up to their heads.
Mariette looks at the stone face in the sand
and makes a connection that changes his life.
If this is one of Strabo's sphinxes, then there is an avenue.
And if there is an avenue, it leads somewhere.
He abandons the manuscripts. He hires workers.
He begins to dig. The avenue is real.
Over the following months,
Mariette's crews uncover sphinx after sphinx,
more than a hundred of them,
lined up across the plateau, along with chapels,
statues and offerings left by worshippers over centuries.
The work is brutal. The sand pours back
into the trenches almost as quickly as it is removed.
Money runs short. There are disputes with the authorities over
who has the right to excavate
and who owns what is found. Mariette keeps going.
In November 1851, the trench reaches a doorway cut into the rock.
Behind it, a corridor runs into the dark.
The air is still and dry and carries the
faint mineral smell of limestone that has
not felt daylight in a very long time.
Mariette and his workers move forward with lamps.
The ceiling is a rough vault cut straight into the bedrock.
The floor slopes.
Their footsteps come back to them off the walls.
And then, the lamplight falls on the first of the boxes.
It sits in a side chamber cut off the main corridor,
a recess just large enough to hold it,
and it fills that space the way a ship fills a dry dock.
It is dark, polished stone. Taller than a man, longer than a horse.
Its top edge well above head height.
On top of it rests a lid nearly as thick as a person's body.
The surfaces are flat. The corners are sharp.
In the moving light of a lamp,
the faces of the stone seem to shift and glow.
There is another chamber beyond it. And another.
The corridor runs on, with recesses opening on both sides,
many of them holding another enormous box.
By the time the full layout is understood,
the main underground complex, the part known today
as the Greater Vaults, holds around two dozen of these chambers,
along a gallery that stretches
for roughly 200 meters, with branching passages
that take the total length of tunnel much further.
These are not coffins in any ordinary sense.
A human sarcophagus, even a royal one,
is usually a few tons of stone.
The boxes in the Serapeum are an order of magnitude larger.
The biggest are roughly four meters long,
more than two meters wide and more than three meters
tall from floor to the top of the lid.
The box bodies are each cut from a single piece of stone.
There are no seams on the sides, no assembled panels, no mortar.
Each one began as a single
monolith and the inside was removed from it.
That detail is the one that stops engineers
in their tracks. Building something big
from smaller pieces is a logistical problem.
Carving something big out of one piece
is a different kind of problem altogether.
Every cut has to be right.
A crack in the wrong place, a flaw in the stone,
an impact during transport, and months or years of labor are gone.
There is no repairing a split monolith.
Mariette's own notes capture something of the shock.
He is a trained scholar, not a sensationalist,
and he understands at once that he is looking at something new.
But he also faces an immediate disappointment.
As he moves through the chambers,
he finds that almost every box has already been opened. Lids
have been pushed aside,
sometimes far enough to leave a gap a person could climb through.
The contents are gone.
Whatever was placed inside, whatever gold, amulets or wrappings,
was taken long before 1851, almost certainly in antiquity.
Robbers had come into these tunnels
with lamps and levers, shifted lids weighing tens
of tons just enough to reach inside, and left.
So the first great question of the Serapeum
is not really what was in the boxes.
The robbers, unfortunately, answered that one for themselves.
The first great question is, what were these boxes for,
and why were they made on this scale?
Here, at least, the ancient record is not silent.
The Serapeum is not an anonymous ruin. Its name comes from Serapis,
a god whose worship flourished
in the later centuries of Egyptian history.
But long before Serapis,
this place belonged to another figure entirely.
Not a pharaoh. Not a priest. A bull.
In the religion of Memphis,
one living bull at a time was recognized as the Apis,
an earthly manifestation connected with Ptah,
the great creator god of the city.
The animal was not chosen at random.
Priests searched the herds for a calf with particular markings.
A black hide, a white patch on the forehead,
special patterns on the body and under the tongue.
When they found it, the calf was brought to Memphis
and installed in its own sanctuary,
with its own attendants, its own courtyard, and its own household.
Pilgrims came to watch it.
Its movements were read as omens. It was fed, groomed,
guarded, and honored for the rest of its natural life.
And when it died, the whole country noticed.
For some 70 days, by most accounts,
the temples of Memphis went into mourning.
Mourners shaved their heads,
offerings stopped and started again by the rhythm of ritual
rather than appetite.
The body of the bull was taken to a special embalming house near the
Temple of Ptah, and here the archaeology becomes startlingly physical.
Excavations at Memphis have
uncovered the place where this work was done.
Enormous tables carved from travertine, each long
enough to take the body of a full-grown bull,
with channels cut into the surface to carry fluids away
and carved lions along the sides.
One of those tables survives today,
its surface worn smooth, its drainage grooves still clean
edged after more than two and a half thousand years.
On tables like these, the embalmers worked
with natron, resins, oils and linen in quantities
that would have dwarfed the preparations for most
human burials. When the work was finished,
the wrapped body was carried in procession
out of the city, up the escarpment to the desert plateau of Saqqara
and down into the dark.
Crowds lined the route. State officials attended.
Pharaohs paid for it,
and in some cases had their names carved into the record of it.
Then, the search for the next calf began.
This is the context that turns
the Serapeum boxes from an unexplained curiosity
into something with a documented purpose.
They are not anonymous containers.
They are coffins, built for a sacred animal that
stood at the center of one of Egypt's most important state cults.
That alone answers part of the riddle of their size.
A bull, embalmed and wrapped, is a large object.
Add the wooden inner coffins, the packing, the grave goods,
the space required to lower everything in,
and a box several meters long stops looking strange.
But it does not stop looking excessive.
Because the box does not need to be four meters long
and over three meters tall to hold a bull.
It does not need walls that are, in places,
reportedly close to half a metre thick.
And it certainly does not need to be carved
from one of the hardest stones in Egypt,
quarried at the far southern end of the country.
A wooden coffin would hold a bull.
A limestone box, cut from the plateau
a few hundred metres away, would hold a bull.
Earlier generations of Apis burials, in fact,
used exactly those simpler arrangements.
So the size and the material are choices.
Somebody, at some point,
decided that the Apis deserved something heavier,
harder, and more permanent than anything that had come before.
And that decision launched an engineering program
that would run across generations.
To understand what that program involved,
it helps to walk the galleries the way Mariette's workers first did.
The main corridor of the Greater Vaults runs
for well over a hundred meters beneath the sand,
cut straight into the bedrock.
It is wide enough for several people to walk abreast,
and tall enough that a lantern held overhead barely lights
the ceiling. The air is still
and dry, with a faint mineral smell,
the smell of stone that has never seen weather.
Opening off this corridor, on alternating sides, are the chambers.
They are not small alcoves.
Each one is a room cut down below the level of the corridor floor
so that the box inside sits in a kind of pit,
its lid roughly level with the walkway
or just beneath it. 24 of these chambers hold great stone boxes.
Stand at the edge of one
and look down and the scale changes how the body feels.
The box fills the room.
There is perhaps a metre of clearance on either side, sometimes less.
The lid alone, lying across the top,
is the size of a small car and weighs in the region of 25 tonnes.
The box beneath it, depending on which one,
is estimated at around 40 tonnes.
Together, the largest assemblies reach roughly 60,
though popular accounts often claim far more.
And that clearance is the detail that keeps engineers awake.
Every one of these boxes had
to be brought down the ramp from the surface,
along the corridor,
turned through 90 degrees and lowered into its chamber,
in a space barely larger than the object itself.
There is no room for a crane, even if one had existed.
There is no room for a large team to stand around the stone and lift.
Whatever method was used, it had to work in a tunnel, by lamplight,
with tolerances measured in hand widths.
It also had to work without bringing the roof down.
The Serapeum is not carved into a solid block of granite.
It is cut through the layered sedimentary
rock of the Saqqara Plateau,
beds of limestone interleaved with softer marl and shale.
These layers are not equally strong.
Some crumble when wet, some fracture along their
bedding planes. The ancient excavators had to cut long corridors
and deep chambers through
this sequence and leave enough rock overhead
to carry the weight of the desert above.
In places, they did it
so well that the galleries stood open for more than 2,000 years.
In other places, as later engineers would discover,
the rock has been quietly failing for centuries.
All of that is the underground half of the story.
The other half begins far to the south.
Most of the Serapeum boxes are made of granite,
and the granite of ancient Egypt has a home address.
It comes overwhelmingly from the region of Aswan,
at the first cataract of the Nile,
where the river breaks over a barrier of hard igneous rock.
From there to Saqqara is roughly 800 kilometres or more.
In modern terms, that is roughly the distance
from London to the south of France,
from Boston to Detroit.
In ancient terms, it is the length of the kingdom.
Some of the boxes are not granite at all.
A number are cut from other hard, dark stones,
which geologists describe variously as granodiorite,
diorite, or basalt-like rock,
and their sources may differ.
That variation turns out to matter,
and it will come back later in this investigation.
But the core problem remains the same for all of them.
The stone did not come from Saqqara.
It was chosen somewhere else, cut somewhere else, and brought here.
Granite is not simply a hard version of limestone,
it is a different kind of material altogether.
Limestone is sedimentary, formed from compacted shells and mud,
and a copper chisel will bite into it.
Granite is igneous. It cooled slowly from
molten rock deep underground, and as it cooled, it grew crystals.
Pick up a polished piece of Aswan granite
and look closely, and you can see them.
Pink and grey grains of feldspar, black flecks of mica and hornblende,
and glassy, translucent grains of quartz.
That quartz is the heart of the problem.
On the scale geologists use to rank mineral hardness,
quartz sits at 7 out of 10. Copper,
the main working metal of Egypt for most of its history,
Sits at roughly three. Even hardened bronze does not come close.
In plain terms, the dominant metal in the ancient Egyptian toolkit
is softer than the hardest mineral
in the stone it was being used to shape.
Drag a copper blade across granite,
and it is the copper that wears away.
This is where the debate about the Serapeum really begins.
Not with the question of whether
the Egyptians could work granite at all.
They obviously could, and the evidence is everywhere,
from obelisks to statues to the burial chamber of the Great Pyramid.
The question is narrower and much more interesting.
How do you take a single block of this material,
heavier than a loaded freight wagon,
and turn it into a hollow container with walls as straight as a ruler,
using tools made of metal softer than the stone itself?
The first stage, at least, is well documented.
At Aswan, in the quarries that still scar the hills above the river,
the clearest evidence lies in the stone.
Workers did not chisel granite out of the bedrock, they pounded it.
Scattered around the old quarry faces are rounded balls of dolerite,
a dense, dark rock tougher than granite,
many of them roughly the size of a grapefruit or a
small melon. Held in both hands, or possibly lashed to wooden frames,
they were brought down again and again onto the surface of the rock.
Each strike crushed a few grains of quartz and feldspar into powder.
Sweep away the powder, strike again.
Over weeks and months,
the pounding cut narrow trenches around a block, outlining it on every
side, until crews could work underneath and free it from the bedrock.
The marks of this method
survive. Along the edges of abandoned blocks at Aswan,
the trench walls are covered in shallow,
scalloped hollows, each one the scar of a single working position,
each one roughly the width of
a man's reach. It is slow, rhythmic, exhausting work,
and it looks exactly like what it is.
That explains how the block comes out of the ground.
It does not explain how the Serapeum
boxes look, because the outside of a finished box
is not covered in scalloped pounding marks.
Its faces are flat, its edges are crisp, and its interior,
the space where the sacred bull was laid,
was emptied of many tons of stone
and left with walls that meet the floor in tight
internal corners. A dolerite pounder cannot reach into a tight corner.
Pounding is a technique for rough shaping and trench cutting,
not for fine interior work.
So the investigation has to move to the second stage of the toolkit,
and here experimental archaeology has done genuinely useful work.
The key is abrasion. Copper on its own cannot cut granite,
but copper combined with sand behaves very differently.
Desert sand is largely quartz,
the same mineral that makes granite so hard.
When a copper saw blade is drawn back
and forth across granite with wet quartz sand fed into the
cut, the copper does not do the cutting.
The sand does. The blade acts as a carrier,
pressing loose grains against the stone and dragging them across it.
Quartz scratches quartz, and slowly, grain by grain, the cut deepens.
The copper wears away too, often faster than the stone,
but it keeps doing its job.
In controlled modern trials,
researchers working with replica copper saws and sand
have cut into granite this way.
The rates are slow, measured in millimetres or a few centimetres
per hour depending on the setup, but they are real and repeatable.
The same principle applies
to drilling. A hollow copper tube spun with a bow
or a weighted crank and fed with abrasive sand
will bore a circular channel into granite
and leave behind a solid core of stone in the centre.
Exactly these cores, and the drill holes that produce them,
turn up across ancient Egypt, from Pyramid Age workshops onward.
Now picture how those methods could combine on a Serapeum box.
Saw cuts define the outer faces.
Rows of tubular drill holes run down into the top surface,
outlining the interior cavity.
The cores are snapped off and removed.
The ridges of stone left between the holes
are knocked away with pounders and harder tools.
The rough cavity is then ground down
with blocks of stone and abrasive paste
until the walls are flat
and the corners are as sharp as the workers can make them.
It is a plausible sequence.
Many archaeologists consider it the most likely one.
But plausible is not the same as demonstrated,
and this is exactly where the debate sharpens.
Hollowing a box this large is not a matter of drilling one hole.
It is a matter of removing many tons of granite from inside a structure
whose walls must stay intact.
A single misjudged blow, a hidden flaw in the stone, a drill run too
deep, and a block that took years to quarry
and transport could crack from end to end.
Every stage had to be coordinated,
measured and checked inside a space where workers had to lean in,
kneel or eventually climb down into the cavity they were carving.
There is no surviving manual
that describes how this was managed.
The procedure has to be reconstructed from the stone itself.
And this is where researchers on the alternative side
of the argument make their strongest case.
They point to the interior surfaces.
Visitors who walk the galleries with a torch
describe running a hand along the inside walls of certain boxes
and finding them smooth enough
to reflect light. Some independent investigators
have placed straight edges and engineering
squares against the interior faces
and reported surfaces that appear remarkably flat.
and internal corners that appear remarkably close to right angles.
Photographs of those measurements circulate widely.
In them, a steel edge sits against dark stone with no visible gap.
To many viewers, that looks less like hand grinding
and more like the work of a milling machine.
It is a striking image.
It deserves a careful answer, not a dismissive one.
The careful answer begins with what a photograph can and cannot show.
A straight edge resting against polished stone,
lit from the right angle,
can hide gaps of a fraction of a millimetre.
A camera lens can flatten curvature.
A single measurement taken in one spot says nothing about
the next spot 30 centimetres away.
And a surface that looks perfect to the eye can reveal waviness,
tool tracks and tiny steps under raking light or a laser scanner.
Hand-ground surfaces can be extraordinarily flat
because grinding with a large flat block
naturally averages out high points.
Lensmakers and stone polishers have achieved exceptional
flatness by hand for centuries.
None of that proves the boxes were finished by hand. It means
that the claim of machine precision rests
on evidence that has not yet been tested the way
it needs to be. What would actually settle it is not another photograph
but a complete survey.
Three-dimensional scanning of every interior face,
flatness mapped across
the entire surface rather than at selected points,
and microscopic study of the surface texture
to find out what kind of tool,
abrasive or motion left its signature there.
Tool marks at that scale can be very informative.
A rotating machine tends to leave regular, repeating patterns.
Hand-driven abrasion tends
to leave irregular scratches that change direction,
depth and spacing as the worker shifts position, tires or changes grit.
One recent study of ancient Egyptian stone surfaces reportedly used
a lighting technique
that photographs an object under dozens of angles of illumination,
then combines the images
so researchers can examine tool traces in fine relief.
It showed how much information survives on worked stone,
and also how much remains difficult to interpret.
Some of the finest marks on Egyptian hard stone sculpture
still do not have a fully agreed explanation.
That is the honest state of the question.
Not a mystery that defeats science,
and not a case that has been closed.
An open technical problem waiting for proper measurement.
And the problem does not end when the cavity is empty,
because every one of these boxes had a lid.
The lids are not thin covers.
They are slabs of hard stone in their own right,
each weighing many tons, some estimated at 25 tons or so.
A finished box and its lid together reach around 60 tons,
well short of the 100 ton figure
that gives the Serapeum its reputation.
And the lid presents a problem the box itself does not.
A box can be slid into its niche and left there.
A lid has to be raised above the rim
of a container already sitting in a cramped chamber,
then lowered onto it without chipping
an edge that took months to finish.
The likeliest method is also the least glamorous.
The niches in the greater vaults are cut below
the level of the corridor floor,
so a box could be eased down into its pit.
Packed sand, timber cribbing
and levers would let a crew raise a lid a few centimetres at a time,
build up support beneath it and repeat.
Lowering it again could be done
by slowly removing sand from underneath.
Nothing about that sequence requires machinery.
It requires patience, planning,
and a workforce that has done it before.
And the Serapeum shows signs that its crews had done exactly that,
chamber after chamber, across many decades.
That raises the question of how the boxes got underground at all.
The main galleries run for roughly 200 meters beneath the plateau,
cut through soft rock,
with corridors only modestly wider than the boxes they carried.
A block of this size cannot be turned sharply.
It cannot be lifted over obstacles.
Every stage of the route, from the entrance ramp to the final niche,
had to be planned around it.
The working theory is that boxes were hauled
on wooden sledges over timber rails or prepared
surfaces, pulled by teams on ropes and steered with levers,
with the corridor itself acting as
a guide. There is evidence that this sometimes went wrong.
One box never reached its chamber.
It sits in a passage short of its destination,
its lid nearby, as if the work simply stopped.
Whether it was abandoned
because of a change in rain, a structural problem,
or a funerary schedule that moved on without it,
that single stranded box says something important.
These objects were moved by people, under deadlines,
and people do not always finish what they start.
Which brings back a question raised earlier.
Why go to all this trouble with granite
when the plateau above is made of limestone?
Limestone was everywhere at Saqqara.
It was quick to quarry and easy to carve.
Granite meant a journey of some 800 kilometers
or more down the Nile from the region of Aswan,
then overland transport, then months of grinding.
The answer, as far as the evidence goes,
is that the difficulty was part of the point.
Hard stone was the material of kings and gods.
It did not crumble. It announced permanence.
A sacred animal regarded as a living manifestation of the divine
deserved a container no ordinary person could ever afford.
And not all the boxes are granite.
Some are other hard stones, including darker volcanic rock.
Their sizes differ, their finishes differ.
A few carry inscriptions, while most are bare.
That variety matters
because it argues against the idea that every box emerged from a single
lost workshop. Different stones fracture and polish differently.
Granite, with its interlocking
crystals of quartz and feldspar, wears unevenly under abrasion.
Fine-grained basalt-like stone
takes a smoother, darker finish.
If these boxes were made over generations, from different quarries
by different crews,
that is exactly the variety one would expect to see.
The written record supports
The Apis cult itself is far older than the Greater Vaults.
Earlier bulls were buried in
separate tombs, often in wooden coffins,
in a sequence that stretches back centuries.
The monumental galleries belong to a later chapter,
begun under Samtik I in the 7th
century before the Common Era and expanded by later rulers.
One of the boxes carries the name
of Amasis II. Others bear dates from later reigns still.
Then there are the stelae.
When the site was excavated in the 19th century,
the walls and corridors yielded
hundreds of inscribed stone tablets left by priests,
officials and pilgrims.
Many record the life of a particular bull, when it was born,
when it was installed, when it died and under which king.
Because each bull's life was dated to a reign,
these modest tablets became one of the most
valuable tools historians have for reconstructing the order
and length of Egyptian reigns in the
later periods. The irony is real.
The most famous objects in the Serapeum are the giant boxes.
The most informative may be the small tablets nobody photographs.
The boxes themselves, when they were opened, were largely empty.
Lids had been shoved aside,
sometimes just far enough for a person to squeeze through.
Robbers had reached the vaults long before any archaeologist,
and whatever was buried inside had been stripped or scattered.
Popular accounts sometimes claimed strange substances
or unexplained contents were found within.
The responsible approach is to separate what excavation
records actually describe from what later retellings added.
A robbed tomb is not a mystery in itself.
It is one of the most common outcomes in Egyptian
archaeology. So what would a modern investigation look like?
It would begin with the boxes that were
never finished, because an incomplete surface preserves
the steps that a polished surface
erases. Rough faces, partially cut areas,
and the stranded box in the corridor could
show the order of work.
Rough shaping, hollowing, smoothing, and final polish.
Each stone would be sampled and matched to known quarries.
Every interior face would be scanned and mapped.
Experimental crews would attempt to reproduce the surfaces with copper,
abrasive sand, stone pounders and grinding blocks,
then compare their results under the same microscope.
And there is a reason that work cannot wait forever.
The Serapeum was cut through layers of limestone, marl and shale.
And those layers do not behave the same way.
Moisture moves through them. Some swell and weaken.
Over the past century,
cracks spread through the ceilings, slabs detached,
and parts of the galleries became dangerous enough
that the site had to close for years
while engineers installed supports and monitored the rock.
The structure that has protected these boxes for more than 2,500 years
is itself slowly deteriorating.
Every year adds new stress,
and every repair changes the context around the evidence.
That is the real urgency here.
Not that a hidden secret is about to vanish,
but that a genuine scientific opportunity is narrower than it looks.
Some researchers believe the precision of these boxes
points to tools more advanced than anything Egypt is credited with.
Others point to experimental work showing
that patient abrasion with simple materials
can produce remarkably fine results.
The fair answer is that the argument has
been running mostly on photographs and assumptions,
and it deserves numbers instead.
Egyptian craftsmen were not primitive.
Their quarrying, their logistics,
and their command of hard stone are beyond dispute.
What remains incomplete is our step-by-step understanding
of how their workshops actually operated on objects of this scale.
Picture it plainly.
A block of granite is split from bedrock in the far south.
It is dragged to the river, floated north for weeks,
hauled across the desert edge,
lowered into the dark, and ground by hand until
its walls are flat enough to fool a modern camera.
Then, a 25-tonne lid is lifted over it and set down without a scratch.
24 times. Over generations.
For animals the builders believed carried a god.
If ancient Egyptians could do all of that,
the remarkable thing is not that they
might have had help from someone else.
The remarkable thing is how much
of their knowledge we still have not fully reconstructed.
So here is the question for you.
If scientists could run just one test on the Serapeum Boxes tomorrow,
would you choose a full laser scan of the interior surfaces,
microscopic analysis of the tool marks,
or a geological match to the original quarries?
And what do you think it would reveal?
Tell us in the comments. And if there is
another ancient site you think deserves
this kind of investigation, name it there too.
