Sphere Making Basics - How To Make A Moss Agate Sphere
1 Video View·Nov 14, 2026
In this video I show you all the steps I take to make a rock sphere. In this case the rock is a beautiful West Texas moss agate!
AI Generated·May contain errors
Hello there fellow rock lovers and welcome back to the channel.
In this video we're going to make a
sphere. You see these three?
I made these three myself from a little jig that I have.
A three-headed sphere making machine.
I use a grinding cup this size. This happens to be a 1200
grit and that gives me a range of about that big to about that big.
You know plus or minus
a little bit. So with that in mind we need
to find a rock that would make a good sphere.
Let me show you what I've got. Check this out.
How does this rock look here? This is a very large
West Texas moss agate. If you look closely, sure,
you can see the mossiness there and there. And as
I turn it over here, this is very large, so bear with me.
So you see some color right there. Very
rough section there. Look at that.
Maybe some dark chalcedony in there as well. That's exciting.
And then over here, I have a big broken face where we can take
an even closer look at the
The mossiness inside this rock.
Check that out. There's some red in there as well.
And notice that the red area has a much
different shine than the rest of it. That's dry, by the way.
I haven't wet that. It almost has that
obsidian look. Although I know it's not obsidian.
But you see what I'm talking about. So this is a
good shape for us to make our sphere.
It's plenty big. I have set up a caliper that I use.
This gives me the maximum diameter I can do and I've taken it
and I've gone around
this big old rock and just checked in different angles to make sure
that we got plenty of meat to work with on this one.
So what I'm going to do next is get this in
the shop and I'll get it on the big 18 inch slab saw.
I'll mount it on the vise in such a way that
I can make one slab, well cut slab whatever,
move the vise way over and then make a second one.
That'll give us a very large piece with which to work that will be
at least that wide because remember
this is the maximum width we can make a sphere with the
particular setup that i have
so i have to make those two cuts one at one end one at the other
end and then that'll leave us that big middle section
to work with so follow me into the shop
and let's get started all right you can see i've got it clamped
in tightly into the vise
it's hanging out quite a bit
so i have to have it very secure now what this will allow us to do
is make a cut. First we'll make this cut here
and then we'll move the vise almost to the very end.
As you can see that will give us plenty of room to make our sphere.
So let me go ahead and make
these two cuts and then I'll show you what it looks like.
And just like that the cutting is
finished. Let's take a closer look at these pieces
because I think we're going to have a really
beautiful. Here's the first piece that I cut.
This will be one of the end pieces. Look at that. Wow.
That's fiery, isn't it? That's really pretty.
I'm not sure what I'm gonna do with these leftover
pieces because by the end of this video,
we're gonna have a bunch of smaller pieces of this stuff
to play with. But for now, that's one edge.
Here's the next piece here. Look at this one. Different
looking right there.
Yeah, this was actually the first cut now that I think about it.
Enough about
those two pieces. Let's look at what's left here
because this will ultimately make our sphere.
Here you can see one side.
Let me turn this big thing over.
This is the other side. I don't really
like this down here because it appears to be a little bit soft.
But we have a big chunk to work
with here. And remember this is the size I can make with the sphere.
So we have to imagine this
coming from this. Oh it'll be fine.
I can always go a little smaller. I obviously can't go any bigger.
So what we're going to do next is get
this big old center slab here mounted on a jig
that I put in the vise that will allow me to make discrete rotations
and start cutting
away at this thing, slowly but surely forming our spherical shape,
our preform as we call
it.
So let's go back in the shop and get this thing back on the saw.
Well, what do you think?
I got the slab mounted in the jig.
As you can see this jig allows me to rotate the slab
in these discrete positions every so many degrees.
Now the key to the alignment I have the width set.
You can see I want to make sure that this dimension
when I cut it will be approximately the same.
It's sort of hard for me to show you this on the phone
but that should be about the same
as this so that when I'm done with all these cuts and
Believe me, there are going to be a lot of cuts.
This preform will be somewhat spherical,
so I'm going to go ahead and get this first cut going.
Once I cut it, I'll rotate it, lock it in again,
cut it, rotate it, lock it in again, cut it,
et cetera, et cetera, until this thing starts to look like a sphere.
The first cut is finished.
Pretty cool, right? So now what I'm going to do is rotate this.
After 12
cuts on
the slab
saw, this
is what
we have.
Check it out.
Funny geometric shape, right?
This out though, isn't this going to be beautiful?
Look at the pattern in there.
I really like it.
I sure hope this thing shapes and shines nicely.
Wow, look at that area right there.
That's super pretty.
Now, we're not done cutting yet.
And as you can see, there are some little issues here.
I think I lost a piece there.
No worries. What I'm going to do next is get this back
on that same jig, only this time I'm going to
put it in this orientation
so that we can start turning it like this as we cut, cut, cut, cut,
12 more cuts.
So we've done this rotation and we're going to do this rotation.
Very important
that I do not move the carriage,
otherwise this thing will not be round. Let me go ahead and get
this back in the shop. I'll put it back on the jig, get it lined up.
I'll show you what that
Let's see what that looks like before we start cutting again.
As you can see, I've got it mounted now back in the jig.
It's ready for its first cut. After I make
the 12 cuts, this thing will look a little like a sphere.
I'll show you that as soon as I'm done
with these 12 cuts. And just like that, the cuts are finished.
Now, as you can see, it's
sort of spherical shape,
but let's take it inside now and take a closer look at it.
After 22 cuts on the saw, this is now what we have,
and as you can see, it sort of looks like a
sphere. Use your imagination.
I know, I know, we're not there yet, but we're getting closer, right,
don't you think? So what we're going to do now
is get it back on the saw once again, only this time
in this orientation. So what I'll do is I'll cut this,
cut that, cut that, cut that, make it even.
More spherical.
And I'll probably do even another angle after that.
The idea being I want to get this as close to round as I can
because before I start on
my sphere making machine,
this thing has to be pretty close to round, otherwise those
grinding cups just won't work.
Is this one going to be a beauty or what?
Look at that.
I am excited about this one.
As you can see, it's going to have little pits in it.
Nothing I can do about that.
Maybe once we get it to that sphere shape we won't see any
of those flaws, but in my experience
we probably are going to have some small pits.
That's okay. If it takes a good shine
it should be beautiful. Look at that.
I won't show you these next few steps on the saw.
What I'm going to do though is I'm going
to get it trimmed down even more. Once it's
done with the saw I'll bring it back in here one more time
and show you before we go back
into the shop and then start manually grinding
off some edges. And I'll show you that.
Here, just in a few moments.
After many, many, many cuts on the saw, this is now what we have,
and it sort of looks like a sphere.
In fact, if we compare it to an actual sphere, you can see
we are getting close. We're not there yet, but we're getting there.
So next up, I'm going to
take this back in the shop. I'm going to get on my carving machine.
You see all these high points?
Now I could let the grinding cups of the sphere making machine
grind those down, but it's going to add a lot of time.
So to speed things up, I'm going to get on my
80 grit wheel on my cabbing machine,
and I'm going to just smooth out all these high spots.
And then we can finally get this thing
on the sphere making machine. Oh yeah, one more thing
before we go back into the shop.
You see, this was a lot of cutting. When you cut like this,
This you end up with, are you ready for this?
A lot.
of trim pieces. You see these are the original big edge pieces
and then lots of this stuff here.
We have some of the smaller pieces that we got
to at the very end of the cutting,
just taking some high points off.
Imagine a lot of these will be thrown into the tumbler. And
let me set this down because look at some of these pieces here,
tumbled up and polished.
These should be beautiful. Oh, look at that one. Isn't that cool?
Wow. So look out for a different video on that.
I'll probably take all of these pieces here and
throw them in a barrel, get them tumbling.
I imagine we are going to have some beauties.
Keep an eye out for that video.
Meanwhile, let's go ahead and get back to the shop where I will
proceed with smoothing out these edges.
This part can be quite fun actually. It's very therapeutic
just to sit in front of the cabbing machine
and slowly grind away the little high points.
I probably spent...
20 to 30 minutes at this point. I think it was worth it.
So what do you think? I decided to go
ahead and grind it down quite a bit actually.
This way it will not take as long to get it into a
perfect sphere once we get it on the machine
which we're about to do next. So you can see what we're
going to have to do is get rid of all of these flat spots
and that's what that sphere making
machine will do with those three grinding heads.
It will eventually make this into a perfect ball.
Next step we get it on the slow speed sphere making machine
and we watch this turn into a
perfect sphere. Now as you can see I've got it in the machine.
I've got my three big grinding cups
on there are water drip going.
So next up I'm going to add a little grit. This is the same
thing we would do with tumbling a rock.
This is that 60 90 silicon carbide and what this is
going to do is embed into those cups and start grinding away.
You'll see the slurry develop.
I'll let this run for several minutes,
and then I'll probably add more grit.
I'll also adjust the different tensions to make sure
that I've got a good random motion of the rock.
As you can see, the motion looks good. It's random.
I don't want to see it suddenly just start turning in one direction.
That creates problems.
So as long as it continues to randomly rotate,
we should be in good shape.
Here you can see we've got a good slurry formed and a good motion.
Now this may take, oh gosh, a couple hours,
but it'll eventually make it a perfect sphere.
It's been going for about, oh I don't know,
an hour maybe, and as you can see it's starting to
turn into a sphere. There are still those flat spots,
but they are slowly but surely grinding
down. I'll check back in, I don't know, another half hour or so.
It's been another hour or so.
It's looking good. The sphere is nearly formed.
You can see there are still some flat spots.
Sort of looks like pepperonis going by, you see those?
Well notice that my grinding cups are getting close,
What that means is I'm going to have to stop this soon
and go to the smaller grinding cups
that actually are sold by Highland Park Lapidary.
I got these from Covington.
They're better at just coarse grinding
to get the basic sphere shape,
So I'll let this run a little while longer
and then I'll have to stop it and move on to the other cups
and I'll also show you what it looks like at that point,
This is how our sphere looks after gosh probably six hours
with those grinding cups. Clearly a
sphere now. However notice it has these flat spots
so we're not done grinding. Check out this pattern
in here. I think we're going to have a beautiful sphere once
this thing gets polished. So what I'm
going to do next is move over to this grinding cup.
Now this is the one that Highland Park
Lapidary sells and these tabs actually
have embedded diamond particles in them.
So this will do a good job grinding.
This did a good job as well, but this just takes the silicon
carbide grit and grinds that in,
And as you know, silicon carbide is not as hard as diamond. Let's
get it back on the machine.
We'll get this cup turning on it and hopefully after another row,
I don't know, a couple hours,
all these flat spots will be gone and we'll have a perfect sphere.
It's time for the diamond particles to do their thing.
Got a good motion. Now you can see over
Over time, we get a little bit of slurry developed,
And after more time, lots of slurry.
That's good.
That means we're grinding it down.
You can see the flat spots are going away.
Oh, now check it out.
Hardly any flat spots left at all.
We are just about finished.
What do you think?
We finally have a sphere.
It's a nice round ball.
Look at that.
And as you can also see, it's not going to be perfect,
You see these little imperfections here.
That's just in the stone itself and
I could have continued to grind this thing down,
making it smaller and smaller, but it's been my
experience that that usually is just throughout the rock,
So why bother making it smaller and
smaller? Now besides, I think once we get this thing polished,
it's going to be beautiful. Look
at this through here. You have to use some imagination.
It's going to look like this
when we're done with a nice shine. Once it has that nice shine,
Ooh, I think it's going to be a beauty.
What I'm going to do next is get this back
on the spear making machine move up to the 220 grit and
once it's finished I'll bring it back in here
and I'll show you what it looks like hopefully
we will no longer have all of these scratches.
Just like with the coarse grit we want to have a
good random motion looks like that's what we've got here
and after a few minutes well check it out
a slurry starts to form that's right the 220 can create
a slurry let's let this run for an hour or so
And just like that, the 220 grit phase of our sphere is finished.
Now we can really start to
see the pattern coming through. You see that?
And it actually has a little bit of a shine on it.
Wow. This gives me hope.
I believe when we're done with this one, it will be really shiny.
Probably even shinier than this one. We'll see.
I'm going to get back on the machine. This time,
I'm going to use the 400 grit cups.
Once again, looking for that good random motion.
Let's let this go for an hour or two.
I'm finished with the 400 grit cups, and here's how it looks.
As you can see, it is starting to develop a decent shine.
I wish this had been a flawless sphere,
but it's just not going to happen.
Now I will be able to clean out that white slurry you see there.
So don't worry about that. That will not be in the final product.
For now though, you can see we're getting a good shine.
The next two cups are going to be this style, not the segments.
But the complete ring, this happens to be the 1200.
I'll do the 1200 next and then the 4000.
After that, we will be finished.
Did I mention we need a good random motion?
And just like that,
the 1200 grit is finished.
I left it on there for a couple of hours. Now the shine is actually
pretty good. Oh, this will be beautiful once we're finished,
I firmly believe. Notice that
that grit is now gone, that slurry that was stuck.
That's just the rock right there.
You ever wonder how you can get slurry like that out
of little tiny crevices? Well, check this out.
It's the ultrasonic cleaner to the rescue.
That's right. Just drop it in, turn it on, and
watch the little clouds of dirt just billow off the surface.
It's kind of fun actually
seeing that happen. Well,
it just takes a few minutes and it's all cleaned up. Now that I've
done that, we're ready to move on to the final grit.
That's the 4000 grit. We're already close.
To the shine on this one, as you can see.
Now let's see what 4000 grit does to it.
Do I really need to say it?
Random motion.
There you go.
Our West Texas moss agate sphere
is finally finished.
Check it out.
What do you think?
Wow.
I just love the details within this mossiness.
Everywhere I look, it's something new to behold.
A very, very pretty stuff.
Oh sure, I wish it had been a flawless sphere.
You see it does have those little pits in it,
cracks. But hey, what are you gonna do, right?
That's just the rock. I like this area right in
here. You see this color? Turn it like this.
I think that's really pretty right there, that red.
See the white and the yellow and the gray?
Yeah, it's very pretty. So the shine's good,
yeah? 4,000 grit, that does the trick. The shape?
Well, what can you say? It's a sphere.
Pretty much matched this one, it's a little bit smaller.
It's okay, I think this shines better on the latest one here.
Well, it took a lot of effort.
And you can do this much quicker with different equipment.
If I had, for example, a high speed sphere making machine,
that would have made a big difference.
Of course, if I had a core saw to cut,
I could have saved a lot of time with my slab saw,
but I don't have those and I only do these periodically.
So I don't worry about that.
If I were a business,
I would definitely want to invest in some faster equipment.
But just to go out and find a big rock and then turn it into a sphere,
I've got everything I need.
And I think the result is pretty nice.
Look at that in there.
I hope you enjoyed this video.
If you did, please be sure
and check my other videos for more like this.
Thanks again.

