Drop In Tub 3 Wall Alcove

Repair house
9 followers
Nov 13, 2026
AI Generated·May contain errors
So we just dry fitted it and I just want to make sure,
you know, first of all that this sits level as it is,
but also come up with the additional framing that we need.
So right now I can see that we need some framing along this side
so that we can mount our backer board on.
And then this wall is going to have to be buffered out
because I'm only, I'm actually
sticking outside of this wall by an inch.
I always recommend if you're going to do,
have an outside corner, having at least an
inch or so outside of the tub
so that you can finish your tile work against it.
Last thing you really want is being butted
up right against drywall because this is a
common area that you end up getting a lot of damage to your drywall.
So if you can buffer this out
so that you can have tile along the edges.
the best way
to go.
So I was really
disappointed
to see this
but this tub
is actually discontinued.
This was made by American Standard and it was called
the fold over edge apron.
It was basically an American Standard studio tub.
that just didn't have the front apron on it
and i thought it was a really cool tub because
it allowed you to put tile on the face
of the tub apron just kind of gives a little bit of a unique
look but unfortunately discontinued it
but really everything that i'm doing here is pretty much the
same way that you would be installing a drop-in tub of some sort
so if you wanted to do a tiled front
this would be a similar way
to go about it it just wouldn't have the same detail
as the american standard but i also wanted to mention that i do
have videos on installing an american
standard studio tub with an apron but all of these
tips that i'm showing you in this video are applicable to any tub
installation it's just going to be a little bit different
because they don't
make the specific one but
If you want to check out the American Standard Studio
with a normal apron, I have a couple of videos.
I'll leave links down below.
Okay, so we're gonna go ahead
and put the drain assembly on.
I find it the easier or easiest to at least
put on your tailpiece before setting the tub.
That's always the hardest thing to install.
So if at the very least,
if you can at least put on your tailpiece,
it'll make things much easier.
Before you're connecting the rest of the plumbing.
So it's really three simple parts,
just a rubber gasket, the tail piece itself,
and this is gonna thread into it.
That's where one of these tub tools,
tub removal tools is really helpful to tighten this in.
And all we're gonna be using is 100% silicone.
This is the silicone that I really like.
I use it for shower doors and everything.
It's a water clear silicone.
Um, really high quality, really durable,
doesn't yellow, um, and it's great to be able to have
this fastened to your, your tub.
So the first thing I do is just get a little bit
on the bottom of your tub, okay, and then
you put your rubber gasket and I even go
do a little bit additional on top of this and
that'll be my tailpiece.
And then for my insert to the tub, put a generous amount
on the back of this and set that aside
and then we'll just put
a decent bead right here
and this is just all of this is just a lot of this we're going to be
wiping away but if you put a significant amount
there you'll make sure you have a good seal you
can even just press
that into place they'll kind
of hold it with the silicone
and you can take your
tub tool just hold this parallel with the tub
and you can just hand tighten
this you want to make
sure that this rubber gasket doesn't slip out
when you compress this all right and you can just take
all this excess silicone and just wipe it off okay
so you have this rubber gasket
Now it is wedged so you have a smaller thinner portion at the bottom
and then it's really thick
at the top so when you're installing this as you can see like even
when this is sitting straight up
this is more slanted up so you need to have
the bigger fatter section of this on top. You want to
put your regular slip fittings on here so you put the nut
and then the slip washer make sure the
tapered edge is towards your fitting.
Actually we do need to cut this down a little bit. I'm
Some silicone around here.
Make sure that, make sure this is pointed
towards
your
fitting,
your
gasket
on this
one.
Okay, so we're gonna set this tub in mortar.
I usually just like to get a 60 pound bag of mortar mix.
This is just your standard Quikrete.
And then just basically mix this
to the wettest allowable amount.
So if you read the back of the bag,
it says maximum water is five quarts.
So if we use five quarts,
that's gonna give us a nice, real loose,
Mortar mixture, we don't want this to be really thick.
If you had an unlevel floor, make this a little bit thicker
so you have the ability of making the tub level.
But in this scenario, everything's level.
So all this is is basically a setting material,
something for the tub to have a little bit of support
so we're not needing to level it out.
So make
it
pretty
loose.
Okay, so we just need some of this mortar
right
in the
center.
Okay, then I like to just use a little bit of silicone
and just put this on our ledger board.
This kind of just gives a little bit of additional adhesion
to this and then you know just in case
anything moves slightly it won't creak
so it's kind of a nice added protection and security to
the walls here.
I'm just going to go
straight across
the tub deck here.
All right so you're
just going to jiggle that around make sure
that that mortar doesn't hold anything up
and really with a level tub or level area
you could even walk on this a little bit.
I did want to mention I was really fighting
that front wall on this particular situation so I took
it out and then just basically installed the tub.
So really everything I'm doing here right now
is essentially exactly the way I would install
a normal American Standard Studio tub with an apron.
It's about three quarters of an inch.
So don't worry about that but just you want to make sure
that you shim
this so it
doesn't pull
that flange
too far.
So I have a
bit more room
on this side
The way that this was a little bit uneven with my tubs.
I got like three quarters of an inch here.
I got about an inch over here.
So not a big deal.
I'll just add more thinset underneath of it
and get it flush with the surface.
But it's always better to be in a little bit
than too far out,
because there's not much you can do
if it comes out too far.
