300 Carat Massive Uncut Gem Plished In Reverse
2 Video Views·Nov 13, 2026
Is bigger better?
Not as often as you would believe when it comes to opal cutting.
A lot of thought goes into the execution of such a large piece of seam opal, especially when the color bar is so visible.
Tune in to see how I tackle this large piece of seam opal.
AI Generated·May contain errors
Join me for a very cool session on a very large opal.
I need to make some serious decisions here about
which way I cut it.
After studying this piece
with a very very thick color bar it has lots
and lots of color in it and
it seems to be clean right through to the other side.
There's only one problem there's some color
But the best colour is right on the line of potch.
I'm going to take a risk.
And I'm going to grind all of that potch
off to make a crystal opal.
The new 90 grit wheel on the
Cabking machine is eating up this potch very quickly
because I have a lot to get through
to get down to that color bar.
Now this is going to be quite a risk if I do say so myself. I don't
know how this color is going to face
but what I do know is I don't want that gray potch on the back
The back of the stone.
I would prefer a crystal opal than a dark opal every day of the week.
And the other thing is, the colour that's the best sitting on the potch
would be best sitting on the top of the opal
and not below or underneath that blue green.
If I grind it the other way around I will end up grinding
that blue green off first to get right
down to that green color on the potch.
So I think this is the best decision but you'll have to stick
around and see
if it works out.
Getting closer
to that color bar
and the potch
is wearing thin
I still don't need to change over to the finer wheel as yet
but I will be when I get close so I
don't get any scratches in the color.
I really am hoping that that green color turns out much
brighter than the purple color below.
If it does we're on a winner. If it doesn't then
well we're back to the drawing board.
And what I am also hoping is that that potch is straight
So that when I grind all that potch off,
it's easy to make one big stone.
That would be the ultimate goal
but it doesn't always work out that way.
So once we
get close
we'll find
that out.
I really
should
have seen
some
color
come
through
by now
and I'm wondering why it's not showing through.
Every press I make on this wheel I'm getting
closer and closer but it doesn't seem to be working out very well
and I'm wondering if it's
actually the potch concaving in.
I have a hunch that I might be right.
There's a bit of color on
The colour on the edge is showing up.
But as I push further and further, it doesn't seem to go in very far.
You can see that colour showing on the edge.
But as I work on the piece, it's not cleaning up in the middle.
And it should be cleaning up there first,
because the curvature of the wheel
means that the centre of the piece should be wearing out first.
So I think I've got a little bit of a problem here.
Oh, and now I've moved from the 90 grit wheel to the 280 grit wheel.
So I can work on it a little bit slower.
That pot should have come out by now
and what I'm thinking is that my last thought about the
concaving potch is correct
and I'm going to have to make some drastic measures here
if I want to
cut a clean
stone or
stones for
that matter.
I really
should
be stopping
right
here but
I'm just giving it a little few more hits
to see how much more comes out
but what I'm wasting is that color
on the edges as I try and get out the middle.
So I have to take some
drastic measures
to save this color
and slice it up.
I really hope this
works out because there's no turning back now.
Once you've made the cut, you've made the cut.
And my hunch
was right.
You can see
those little
potch lines
concaving into the green color.
So if I had gone and tried to take all of that out I would have
lost
most
of the
color.
Even
with
these
small
stones
I'm
struggling
to get
the
potch
out.
So, if I had left it one big stone,
I would have had to dremel it and make a mess of the
piece in order to see that nice colour.
So I think it's best if we were to cut it up into smaller pieces.
I can make
nice pleasing
shapes and
with these two,
I'm going to
make a really
nice pair.
They're nice and close
in size now and I can work on
the other pieces and I've got the
We've got the same problem again.
That concaving potch. So it looks like every piece
is going to be a lot smaller than I first thought,
which is actually fine. It really doesn't matter too much about
the weights or the sizes of the stones
when it comes to this type of opal.
And the reason is I don't price this type of opal per carat.
I usually price it per piece.
And that is because there's usually a lot
of excess on the backs of the stones or there's
color on the back that we don't really need being a crystal.
So I just price it as one stone value.
I was away last month at the Hong
Kong trade show and a lot
of people came up to me and said
is black opal from Lightning Ridge and I said yes it is.
And they showed me some opal they'd bought
and they thought it was black opal and I said
just because opal comes
from Lightning Ridge doesn't make it black opal.
It's its body tone that makes it black opal.
So for instance these pieces here come from Lightning Ridge,
they're definitely not black
opal.
They are dark opal or what I'm trying
to do is make them into crystal opals.
Like taking the potch off the back and making them more translucent.
So that's a bit of a fallacy and an old way for people to sell opal,
to say that if opal comes from Lightning Ridge, it's black opal.
That's so not true.
Making you aware of these things helps you
and arms you a little bit better
when you go to a seller and try and buy some opal,
and they tell you one thing, hopefully you've learned something to say,
well, actually, I know better.
These are the preliminary shapes. I'm quite happy with what's come out
and now it's time to polish them.
Cutting opal is a pastime
that takes many years of practice
and still after 35 years it still throws me curveballs
and says you haven't figured me out
yet have you? And it seems to happen time
and time again and that means I'm still learning
which is what keeps me in the game,
keeps me on my toes and keeps me loving cutting opal.
And while I was hoping for a larger piece,
I still would have considered chopping it into smaller
stones. The only difference is I would have had
a really great surface to mark out the gems where
I wanted them,
but instead I had
to guess.
But it still
worked out okay.
This triangle
while it's nice
I thought it might be better to trim it a little bit further
and make it a beautiful drop shape.
This still can be done on the dopstick you just have
to make sure that the dopstick's small enough
and the wax isn't protruding out too far so that you hit the wheel
when you're grinding
the stone in.
There were many ways
to cut this piece
and this was my way
but I'd love to hear your thoughts about
what you think you would have done.
Leave a comment below and if you haven't subscribed,
I hope I've earned it this time round.
Well this was a really fun cut.
I enjoyed taking away that thick layer of
potch to see the reveal. I bet you're wondering what did it cost
me and what did I make? Any profit? The piece cost me $2,300
and now they've been cut we come to an overall price of around
$3,500 for all of the gems together.
A nice earner for the day. Yeah I agree.
I hope you enjoyed this one,
thanks for watching and we'll see you next time.

