What's Under The Paint? | Strippping Paint From A Mid Century Thrift Store Find

Trash To Treasure
3 followers
This was one of my most rewarding projects. Who knew such beautiful wood was hiding under that paint?
#TrashToTreasure #FurnitureRestoration #Upcycling #ThriftStoreFinds #WoodRefinishing #MidCenturyModern #WalnutRestoration #PaintStripping #OxalicAcid #WoodworkingTips #DIYRestoration
AI Generated·May contain errors
Video Summary
AI GeneratedA craftsman restores a thrift store walnut table purchased for five dollars. The process involves removing layers of old paint, treating deep stains with oxalic acid, repairing structural joints, and using grain filler to hide paint remnants. The project concludes with a strategic staining and polyurethane finish to achieve a \"gently worn\" aesthetic.
I found this table in a thrift store. At first I had no interest in it,
but then I decided to take a closer look.
It had obviously been painted, but when I flipped it over
I saw some nice walnut veneer on the underside,
and I could see that the wood trim around the
edges was solid walnut.
They had it marked at $10, but it was 50% off furniture that day.
So I figured for five bucks it was worth taking
a chance that there was a good-looking walnut table
under
the paint.
The first
thing I
had to do
was to take
off all of
the paint.
I was able
to remove
the upper tier to make it easier to scrape underneath it.
All I had to do was remove a
few screws.
Luckily
there
wasn't any
glue used
to attach it.
Once I had
scraped off
as much as I
Then I went over the whole thing with some 100 grit sandpaper by hand.
To get off as much of any remaining paint
or finish that was on there and I taped off the
front and back pieces of trim
because the grain on those pieces runs perpendicular to the grain
on the top. So I didn't want to accidentally sand across that grain
and leave cross grain
sanding marks. With all of the paint removed I could see
that there were some stains on the top.
There was this black ring towards the front of the table,
and then towards the middle there were a
couple of black rings. They might be a little hard to see on camera,
but they're there. And there was
also this black stain here. Not sure what that is.
Maybe ink. And there was also a mystery black stain
on the top level. To remove these stains, I applied some oxalic acid.
Oxalic acid works really well
To remove black water stains.
Which is what I'm assuming the black rings are.
And as far as the other spots,
I wasn't sure if it would work or not with those,
but it was worth a try.
I let it sit for a while
and cleaned off any residue that was left.
And I could see that the stain on the upper level was completely gone.
The rings down on the lower level near
the center of the table were mostly gone.
There was maybe a faint shadow of them.
The ring at the front was a lot lighter.
You could still see it, but it was a lot better
than it was before. And the spot in the middle was still there.
It didn't look like it had lightened
at all. So I decided just to leave that one for a while
and come back to it after I had applied
some finish and see if it was still visible
and if I wanted to try some touching up. I did have
I did have to make one small structural repair.
This piece of trim was loose at the corner.
So I just needed to glue that up.
I used super glue for this instead of wood glue
because I couldn't see inside the joint and I didn't know if there was
some debris in there or dried glue
or something that would prevent wood glue from sticking.
So I decided to use the super glue
which sticks to both things and I taped off around
it just so I could avoid getting super glue anywhere
that I didn't want to get it.
Despite all of the scraping and the sanding that I did,
there were still some remnants of the paint in the pores of the wood.
Here you can see some little specks of blue paint,
and these are stuck down at the bottom of the pores.
So I needed to get that paint out somehow. I couldn't sand it out
because that would require sanding all
the way to the bottom of the pores,
which would mean I'd end up sanding through the veneer.
So the first thing I tried was a brass bristle brush
and this actually did help. It got out a
pretty good amount of paint
but there were still some specks that I could see that were stuck in
the grain. I decided instead of trying to get
those out I would just cover them up. To do this
I used some grain filler. The filler that I used is from TimberMate.
It's a water-based wood filler
and the idea was that I would fill the grain with the wood filler
And that would cover up the paint
that was down at the bottom of the pour.
But before I applied the filler,
I did seal the wood with some shellac.
And I did this so that the color
that's in the filler wouldn't
penetrate the wood and stain it.
Once the shellac dried, then I could apply the filler.
And I just tried
to make sure I got it down into the grain.
I'd like to thank everybody for watching today.
And I'd like to invite you to check out my Patreon page,
where you can help support this
channel while gaining access to behind the scenes videos
and updates from me.
I'll put a link in the description below. Thanks!
Once it was dry,
I sanded off any excess filler with some 120 grit sandpaper.
So that removed the excess on top,
but it left the filler
that was in the pores of the wood.
When the filler dries it looks chalky like this,
but when I wet it down here with some naphtha
you can see what it'll look like once finish is on it.
And this did actually work. It covered up
those little specks of paint that were in the grain.
Next it was time to apply the stain. I
wasn't sure at first if I wanted to use stain for this one.
I considered just putting a clear finish
Because most of the piece has a nice rich color in the wood,
just on its own without any stain,
but it's not consistent throughout the whole piece.
For instance, the upper tier is a little
bit paler than the lower section
and the grain isn't as interesting. So a stain can help to bring
some consistency over the entire piece
and deepen the color a little bit on the upper tier where
Where it's a little pale.
Also, there were some defects that I couldn't get out,
and I could have just left them
and gone for an intentionally rustic look, but I don't think
that kind of a look works that well with this style of furniture.
And the way I see it, there are three levels that you can go
for when refinishing something, either the intentionally rustic look,
or the gently worn look, or the showroom fresh look.
Intentionally rustic, where you just leave all
of the defects out in the open for everyone to see,
that can work in some styles of furniture,
but I feel like in mid-century modern, like this piece,
or at least what this is trying to be, it doesn't really work as well.
The gently worn look,
I feel like that works better for this style,
so that's what I'm going for here.
Where there are still defects in it, but I've tried to blend them
in a little bit so they're not popping out quite as much.
And then the showroom fresh look, that could look great,
but that takes a lot of time and dedication,
and sometimes it's just not possible,
especially on a piece like this where there's veneer.
And if there's any kind of defect in the veneer
that you can only get out by sanding, then
There's only so much you can do because you can only sand so much
before you go through the veneer.
So I usually go for the gently worn look.
And that's what I'm doing here and that's why I'm using stain.
It'll just help to bring some
cohesiveness over the whole thing
and hide some of the defects a little bit that I couldn't get out.
For the top coat I chose
a wipe-on oil satin
polyurethane.
After the second coat of polyurethane had dried,
I went back and took another look at that
black stain that I wasn't able to get out earlier.
And it was still visible,
although it wasn't too bad,
but I decided to try and touch it up a little bit.
To do this, I took some Mixol tints
and mixed up a color that looked like it was a good match,
and then I mixed that with a little bit
of the shellac that I used earlier.
And just brushed it on and I wasn't trying
to cover up all of the black marks because some
of them actually blended in pretty well
because they were right on a dark grain line. I just
wanted to break up the marks enough
so that your eye wouldn't be drawn to them.
Once the touch-up had dried, I went over the whole table with another
coat of the polyurethane.
And here it is, all finished.
Thanks for watching.
