How to Upgrade Your Orange Pine Furniture with an Easy Paint Wash

Trash To Treasure
3 followers
Same dresser, two similar yet very different looks! I had the opportunity to buy back a piece that I had previously redone just over two years ago. I'm doing a two toned look again, but with even subtle differences in colour and styling, AND different hardware, this piece has a fresh new look. I was also able to make repairs to the drawer guides that I wasn't able to do the first time around.
#furnitureflip #refinishing #painting furniture #furnitureflipping #fusionmineralpaint #furnituremakeover #furniturerepair #pine #pinefurniture #dressermakeover #paintedfurniture #paintwash #Upcycling #Zerowaste #Diy
AI Generated·May contain errors
This video is sponsored by Skillshare.
Back in early 2021, about a month before I started my
YouTube channel, I bought this dingy beat-up pine dresser
from Facebook Marketplace and I
gave it a whole new look.
I gave it a two-tone look, I added new hardware, I did a white wax
on the pine to kind of tone down the orange,
and I believe it was a custom paint color.
Fast forward to a few weeks ago when the person
who originally bought it had mentioned that they
were moving and didn't have space for it in their new place.
It had been used this whole time as a
kid's sort of art center and I
also believe they had their TV on it if I'm not mistaken. This was
a great flip for me at the time
but as you can see the little ones have done a number on it.
I purchased this back from the original buyer
because I wanted to take this and give it a
very similar yet completely different look.
Two takes on the same piece pretty much two years
apart. Stay tuned. My name is Angie and I refinish furniture.
Sometimes I paint and sometimes I don't
but I always do what I can to save old pieces from the trash.
Welcome to my workroom.
So starting things off here as always I'm going
to remove the hardware. Now I purchased this
hardware brand new at the time.
I don't know yet if I'm going to reuse it but I'm going to set it
aside in case I decide to.
These have metal tracks on the bottom of the drawers and wooden runners
and you'll see here in a few moments that some of these runners
or guides are not in the best condition
This was a known problem when I sold the piece
and I made sure that the buyer realized that
there was an issue with a couple of them.
At that point in time I did not have a table saw
nor the skill to recreate these.
He is actually a very talented furniture maker and said oh no
problem I'll do that myself.
But as tends to happen we don't get to projects sometimes so
So he never did fix the broken or missing guides.
When I originally did this, I actually drilled new holes.
The original hardware was on the edges and
I made handles in the middle. It was just the look I was going for.
These two bottom drawers were the
ones I remember having the most issues
and that is because the runners were gone completely.
All in all actually, aside from some kids artwork on this dresser,
it actually fared pretty well.
I did a white wax on the top
and you can see with a little bit of mineral spirits most of those
crayon marks and marker marks,
they actually just scrubbed right off. But the other reason
that I'm using mineral spirits here is because I need
to remove as much of that white wax as
possible because what I want to do this time around
is do a paint wash on the top.
People often ask if you can paint over something
that's already been waxed and
yes you can but this is a necessary step.
You might not get all of the wax off but
you need to get as much as possible before you
do either your scuff sanding if you're
painting over paint or in this case
before I sand down to the bare wood.
Now you might be looking at this and thinking
that the white wax looks a little bit yellow
and that's typical for pine.
What's going to be different about my new look
for this piece is that I'm going to be
doing sort of a tan or beige wash
and it's going to neutralize that orange and yellow
color and I'm not sure if this is gum
or some sort of like Play-Doh or something but I'm
just going to scrape that off and continue cleaning.
Now some of you know that I was actually sick last week and it kind
of threw a wrench in the order of the videos that I'm putting out.
Initially, because I had to film recreating these wooden guides,
I wanted to do the video
on how to do that before this video came out,
but it ended up getting switched around.
So in this video, you'll see me recreate the guides,
but it's going to be kind of a brief
overview.
The second video is actually going to go
into more depth about how to do it and how to make
different types of guides,
so make sure you watch for that in the next couple of weeks.
So you just saw me go over the painted areas
with mineral spirits as well because I
do believe I sealed those with the Fusion Mineral Paint beeswax
at the time so I just
want to remove that. I am going to be painting
the lower three quarters to two thirds of this piece
and having the upper quarter or third approximately be wood grain.
It's a bit different than what I initially did where I had a two-tone,
and even though that sort
of dipped look is not new, it's not groundbreaking,
it's been done for a while, as soon as I saw this
piece come up for sale again,
I knew that that's what I wanted to do to it.
I always like giving the drawers a bit
of a refresh even if it's been scrubbed
and cleaned which this one has.
Everybody that buys a piece of refinished furniture knows that
it's used but my goal is to make it feel as new as possible
and I didn't really get to do that
the first time around with this because there
were some things that I wasn't capable of fixing
I wasn't mixing at the time, but now I can,
so I want to make this as fresh as possible.
For the lower four drawers that were already painted this sort
of custom gray color, they are going to remain painted,
but I'm going to be doing a different color.
So I'm just doing a scuff sand here.
This has already been cleaned with Mineral Spirits.
I believe I'm using 180 grit here, and my goal is not to get all
of the paint off, it's just to smooth out any imperfections.
Pine is very soft and obviously paint
or any other finish is not going to protect it from
the dents that come with use over time.
I also did a very quick hand sanding after
the machine sanding and then wiped off any dust.
I'm going to be using two different
paint colors on this. I'm going to be doing
a paint wash with Algonquin by Fusion Mineral Paint
and then the lower portion of the dresser will be painted in this color
oakum which is also gray
but it leans more brown than what was previously on the piece.
Oakum is a really beautiful color and can read differently depending on
the room and the lighting that it is under.
This is the same color I used on that little
mid-century chest of drawers a while back
that I hand drew the flower on the front of.
Usually when I'm doing my first coats
of paint I'm not at all worried about coverage.
In fact your first coat generally does better
in terms of adhesion if your first coat is thin and
it also gives your second coat something to grip to.
So don't worry if you still see some of what
is under the paint showing through
on your first coat, you'll get it on your second.
So where this new design is going to differ
from the old one aside from the subtle shifts in color
is right here. What I want to do is strip the paint above this tape
so that the top and about a third
of the way down will just be wood grain. This won't just
be on the sides, it'll
also carry along the trim on the front on that top third. The top three
drawer faces will also be the same color
as the side here that I'm getting ready to strip down.
So that the top three drawer faces kind of blend in rather than
stand out with contrast like the original design.
This is also known as a dipped look and like I said before this isn't
groundbreaking or some new trend. It's been around for a little while.
It is very popular so it should sell well
but the main reason I want to do it here
is to show you how just little tweaks like where you put paint
and where you don't can really make a difference in the final product.
I'm using circa 1850 stripper here to remove this paint
and I do remember when
I did this initially that I did not use a primer
which will really help when it
comes to taking the paint off.
Now there are two camps of people there. There are
people that say to prime every time you paint
and there are people that will
prime in certain situations and I fall into that latter category.
The adhesion of the paint was not an issue on this piece at all
and I didn't show it but
initially when I got this back I did a little scratch test
and that paint was rock solid.
What makes this part easier is that there was no primer
so it'll make stripping it
way faster. But just before we get into that I want
to give one minute to today's sponsor.
If you've been on my channel for a while,
you guys know that I am a perpetual learner.
Skillshare is an online community of curious people just like me
who are trying to find
our own creative voices and take control of our financial futures.
And for me, that's in a less traditional way.
This class by Sonia Rasula is about how
to build a digital presence for your creative
career, whatever that may be.
And Skillshare has many other classes in this same realm.
They make it super easy to find what you're looking
for and I love that you can filter the
results, whether that's by skill level
or the amount of time you have. And often when I'm
searching I'll just go in to whatever subject
and save a bunch of classes that interest me to watch
later. You can watch them on your computer,
you can watch them on your phone or tablet.
And these classes are well thought out,
well filmed, and I just really enjoy them.
The first 1000 people to click on my link
in the description box below will get a one month free
trial of Skillshare where you can check out the platform
and get started on your own creative
journey. Learn how to design a career to fit you.
I was able to use just a putty knife on the big
flat areas and then I used this stripping brush
which has nylon bristles to get in and around the trim
It gummed up pretty quickly
and wasn't all that effective on this particular paint,
so I added a bit more stripper
and then went in with some steel wool and that did the trick.
Once I had the majority
of the paint stripped off,
I was able to go
in and start sanding.
People have been asking me why I don't use Mr. Dewalt
as much anymore and the main reason is
right here. The shape of this sander makes these areas
so much easier than the round orbital
sanders. It's also a lot flatter than my Dewalt
so I'm able to get into these areas where my other
sander might be a little bit too high.
My first sanding here was with 150 grit and then I went
Went back in after with 180.
Now the top here is where you can really see the difference between
the bit of white wax that is left and the natural color of the pine.
And when I say natural color of the pine I mean when it's raw.
As soon as you put any kind of seal coat
on top of raw pine it usually goes either
super yellow or super orange
and then of course it will patina and get darker over time.
Now there were a few areas that were indented where
the white wax had kind of settled in,
such as those spots.
Because this is a solid pine top, I'm actually able to kind of sand
that out without worrying about busting through veneer, for example.
Just doing a scuff sand just like I did
on the drawer faces that are going to be painted.
There's a couple areas of concern, not concern,
but a couple areas I have to pay attention to
such as the top here and whenever you're painting over something
that has both raw wood and paint
showing you need to seal it with something
so that you have a consistent layer underneath your paint.
Otherwise your paint can absorb differently
and you'll actually see that spot through the paint.
So you see once I'm done kind of scuff sanding everything
and smoothing everything out,
cleaning it up, I'm actually going to go in with some spray primer
and just use it on the areas
where there is some raw wood showing.
Just a very light layer and then I'm going to let that dry.
I don't have to use it everywhere,
I just need to use it where there's wood showing.
Now there are many different colours I could use for my paint wash,
and many different ratios that I could use,
but what I'm going to do here is take an empty fusion jar
and divide it up into eight parts.
This is normally what I do whenever I do a custom colour,
it allows you to put fairly equal amounts in.
I know roughly how much paint I'm going to need for this.
I want to make sure that I mix enough that I don't have to remix,
but I also don't want to have too much, so it's a bit of a guessing
game, and the more you do this the better you'll get at it.
What I'm doing here is using two
and a half parts water to one and a half part paint.
You could stir or shake this. Normally
if it's solid paint I will stir and shake,
but these paint washes usually a good shake is enough.
Now my goal here isn't to completely cover the wood grain,
but I want to tone it down.
I want to minimize the contrast between
these two different color woods, and I also want to
sort of neutralize that orangey yellow color.
Some people like that. I am not personally a fan.
With paint washes you need to move really quickly especially
the more paint you have in your ratio.
Doesn't really matter how you get it on just get it on quickly
and keep going over it so that it
stays wet. Once you have it completely covered
then you can go in and wipe it off. I normally
use a shop towel for this but you could also use a rag.
Keep wiping until there's no more
More paint coming off and everything looks smooth and even.
And this is what it looks like.
You can see now that that contrast between the two colors is
way toned down, but you can still see the wood grain which is nice.
Now if I were to reuse the hardware that I bought for the first flip,
it would look like this,
which doesn't look bad, but it definitely has
a bit of a country vibe. And what I want to do
this time around is elevate that a bit,
so I think I'm going to do a different type of hardware.
When the time comes to get ready to do the lower part of the dresser,
I'm just going to grab a, I think this was a 180 grit pad
and just gave it a very light sanding and this is going
to make sure that those sprayed areas match the painted areas
so that when I paint over it, it looks like one cohesive layer.
That first layer
of paint has dried.
I'm going to tip this
over onto its back
because I want to get
at the underside
of the rails and also I
need to get at the feet.
I'm also going to paint that little middle support section.
This all needs to get cleaned up under here before I do
the paint wash on the top section and I also want to clean up
the lower section. Now it's kind of funny
because I started to remove the legs and
then I realized that if I'm doing a true dipped look these
legs need to be painted.
And you can see I just kind of paused there for a second.
I was like, wait a second. So initially I
did the two-tone and having the legs wood looked nice,
but because this is a little bit of a
different style, I'm going to need to paint those.
So I just put them back. And now this is what this
looks like with the underside
taken care of.
There's one little area
of paint in this little
nook, which I had a feeling was going to happen.
So I just scraped that out and then did a little
Now you may have noticed, because I have just noticed,
that my hair is a different color now.
I finally went and got rid of the friggin' gray hair.
I'm prepping this now to do the paint wash
on the top part of the dresser and this part
I'm a little apprehensive about.
Not so much the sides here but the actual top. Doing paint washes
over large areas is, I don't want to say difficult,
but you have to work so quickly and it's
really easy to mess it up if you get distracted for a second
or have to slow down for some reason.
It's so important to keep moving
and keep that area wet until you can wipe it down.
Adding a little bit of Howard Feed'n Wax inside the drawers
and this is something that I get
asked about often, whether it leaves residue on clothing
or if it gets sticky and the answer
is no if you use it properly.
So this is not something that you just brush on and leave it.
Once you brush it on, let it sit for a little bit,
you have to wipe all of the excess off
and then let it completely cure before you use it.
So even though Fusion Mineral Paint
technically has a built-in top coat,
once you dilute it, such as in a paint wash,
it loses that property, so you need to seal it.
I'm going to be using Varathane Premium Diamond Wood Finish,
which is a water-based polyurethane.
It looks milky in the can and as you're applying it,
but it dries clear and doesn't yellow.
Just like polycrylic, I prefer to apply this stuff with a foam brush.
It's just the way I learned to do it,
and it's what I'm most comfortable with.
This stuff does have pretty good self-leveling properties as well.
Some people like to brush it on.
It's a little bit trickier on the top.
Again, because it's a large area,
you have to move quickly without overworking the area
and without going back in and brushing stuff
that's already started to set up.
And here's a good example of, like I said,
how it looks milky, but it does dry crystal clear.
Okay, so as I mentioned in the beginning of this video,
there are a few wooden drawer slides or guides
that need to be replaced.
And I also mentioned that I do have a separate video
coming out very soon.
In fact, it'll probably be the next video that comes out
where I go into a lot of detail
about how I actually do this.
Rather than repeat myself twice,
I'm just gonna kinda quickly go through this here.
And in that coming video,
you'll see how I make a couple of different types of drawer guides,
because they do come in different shapes.
The shape that is used on this dresser
is what I call an H shape,
so basically all I have to do is cut some pieces out of hardwood
that are the same length, width,
and depth as these pieces that I took off the dresser,
which serve as my templates.
And then I have to cut some grooves or channels in it.
It's one of the most common repairs that I have to make in furniture
and because of that whenever I
do make guides I tend to make a bunch of extra ones
so that I don't have to do it as often
because I don't have a permanent setup for my table saw.
It's a mobile unit so I have to
take it out and get it set up every time
so I like to minimize how often I need to use it.
All I'm doing here is now cutting the grooves.
This would be a lot faster with a router setup
or dado stack which I do not have, the latter that is,
and in that upcoming video I'm just going to
show you how to do all of this with just a table saw.
So basically what I'm doing is making multiple
passes to create these grooves or channels
and then I can test it in the track. Now you don't
want it so tight that it catches,
you want to have a little bit of wiggle room there.
This particular one has holes in both ends,
that's how it attaches to the piece.
So basically I am going to drill my inner hole first,
and then use a slightly larger bit
to sort of countersink that screw head.
You can use a countersink bit if you want for the second part,
I actually show that in the other video as well.
But here this is just an alternative way
to do that if you don't have a countersink bit.
Once my new guides are all ready,
I can remove the old broken one from the top here and replace
it with a new one and then add them
into the bottom where there were none to begin with.
Of course I can't
wait to test these.
It's perfect
and I'm very happy.
A lot of the wooden drawer stops,
which are these little pieces that attach to the frame
that keep the drawers from pushing all the way back,
they were missing so I had to replace a
I replaced a bunch of those and also added a bit of feed
and wax to these drawer guides.
As far as hardware goes I did try the black ones
and I did like it but I'm leaning more towards
these. I want this to have more of a modern upscale vibe
this time. I'm really curious to
know what you guys would pick whether you would prefer the black ones
or the gold ones. You'll
see the reveal with the gold ones
but let me know in the comments below which ones you like best.
Well, I hope you've enjoyed this video so far.
It's been really interesting to see this piece
go from this sort of dingy orange pine dresser to this first iteration,
which was a really cool
two-tone high contrast piece.
And then I ended up buying it back two years later and doing something
very similar, but with subtle differences.
And I think it makes a big impact. I hope you enjoyed
this reveal. I love how this piece turned out.
As always, thank you so much for watching. Don't
Don't forget to like and subscribe if you like this sort of content.
content and I will see you next time.
