转载-ABAQUS学习 Charpy Impact tutorial - Johnson-cook material + Damage
Nov 15, 2026
AI Generated·May contain errors
Hello friends, welcome to Abacus Acumen for quick
and sound learning. So in this
video tutorial I will explain you about the Charpy impact test simulation
and this we are going
And about the Johnson Cook material model, if you refer back
to build in abacus
to one of our previous video wherein we have explained you about
ea 6.14 pre-processor
the background of the Johnson Cook material model
with the damage evaluation and the typical use of Johnson Cook material
is the where you want to represent the triaxial state of stress
plus the strain rate effect
and the temperature effect in one material model that is a one
universal material model for the metal
so where you can conveniently use the Johnson Cook material
model and in earlier video I also give you few references in terms of
the technical papers which thoroughly explains you about
or the uniaxial tensile test
which can be used to develop the material parameter material constants
so in this tutorial I am going to use the reference
or the material parameters and the damage
parameters directly from the test reference test paper
so over the time I mean how you go through
this video you will understand
the the different critical steps involved setting up this simulation
for this Charpy sample test so let's go back
and understand some of the inputs for this
simulations this is the FE model setup the Charpy impact test
so it has a sample of 10 by 10
size with around 56 millimeter is a length and out of 56 millimeter
around 40 millimeter is simply supported
so we are going to have so this
setup is taken from the ASTM E23 requirements
so you can always refer this is one of the
standard method which is referred as ASTM
E23 so you can always procure this
test document and go through
and understand the how exactly this test has been conducted so for
for this simulation and for this demonstration purposes I have
Hello, hello.
compile this information in this slide so we have this simply supported
condition with the 40 millimeter of span
with a V-notch around 45 degrees
degree Celsius and the depth is two millimeter of this V-notch
and there is an impactor
which is I'm going to model with the with the steel
properties
And this has the chamfer radius of 0.8 mm
with a 30 degree as an angle between these two edges
and the material what I'm considering for this simulation is sample
is aluminum and the unit system is Newton ton millimeter and second.
So approximately I'm applying the impact velocity of 2500 mm per second
and the impactor mass which is around 1.5 kg.
This mass I am representing by manipulating
the density of the impactor that is the steel
material.
So although it won't remain steel if we change the density
but for the simulation purpose
the properties that modulus
and all I am considering the steel modulus properties but when we apply
the density so I am going to change it to this number
so that it will represent 1.5
kg.
This is one way where we can use the density numbers to
well get the the mass we want during the impact
so ultimately we want to apply the kinetic energy
the initial energy and that is uh it's kind
of converted from the potential energy calculation
from the JRP impact test setup
that is uh you can do some hand calculation in the
background and understand what is the initial impact energy
so so the for that the
the inputs for us over here is 1.5 kg is approximate mass
and then followed by this
impact velocity that is the kinetic energy it will give
and that particular kinetic energy is the
initial impact energy
for this aluminum sample toughness evaluation okay let's go back to
the Abaqus CAE tool so let's start with start with the sample
so let's build the geometry first
And then we'll apply the loads and boundary condition part
and of course the critical part is the
material model definition that is a Johnson Cook in Abacus.
I am going with sample that is a
solid extrusion continue.
So initially I am going to build the profile.
It will take couple of
minutes to get this done
the geometry part.
So those who
are familiar with the
building the geometry part they can skip
and they can directly go to the time instant where
i'm going to explain you about the material model part
so i do i but just to have a flow
and the
continuation
i advise
you to go
through
the all the
details
step we
have depth
it's 10
millimeter okay so this is what we have
and then let's understand the datum part so i will go ahead
I will go ahead and create the assembly part for this so that
We can slightly do a positioning part over here.
So for convenient purpose and other geometric operations,
I am shifting here to 0, 0 coordinates.
So let me understand
the distances.
So in X direction,
minus 6.81, okay,
so we'll go
to the part again
and I will do some
partition
activities.
We can just follow.
So this I'm doing it to have a geometry based boundary conditions later
on and also it will help in having the fine mesh at the center
and which is very important when we do this sharp impact test.
So this is YZ
plane set 0 0
and go back to
the assembly
part.
So here I
will create
YZ plane.
Yep. And then
do the
partition
of this cell
using datum
plane.
Make dependent.
Okay, so we'll do this as well.
Make dependent. Let us try it now.
Select the datum plane.
All right, this is done.
All right, so it is there.
So here in this portion,
I'm going to do a fine mesh.
And then so this edge I will use it
for the simply support
condition that is a 40 meter span,
these two edges.
And then so other one is a there
is kind of an overhang portion
for the sample. Now let's build a
the anvil part
so this is a
chamfer so here
the radius
is fillet radius
is 0.8 select
the two sides
so it automatically creates
and then we'll have try to have an angle over here that is 30 so we'll
make the equal length for these two sides
and these two sides also we want to have equal length
all right and then we can set try
and set up this angle, okay, this sounds
good and now we'll extrude it by
14 millimeter let's say so it's slightly it will it
is having the width of the sample piece and with
the two millimeter overhang on each
side so maybe i think so we have
to do a repositioning over here
let me
measure
few
distances
x is
28.751112751812
okay
this is
in y
plus two
millimeter
So now we will go and create the properties
for this different materials.
So first is the for the part sample, okay.
So this is the critical
part guys.
So I want you to make
a note of these things,
this is the aluminum
material.
So Young's modulus
is 70 GPa, 0.3 density,
I will define 2.7
E raised to minus 9.
so just to remind you we are using the metric system
of newton ton millimeter and second so
so that is the reason you're seeing
the mass density it is in ton per millimeter cube and
then let's go for the plastic part
so here we are to select the Johnson Cook and you now we are
defining the parameters for the Johnson Cook equation
so that is the first parameter is a
three two four so so when we
while doing this so i expect you that you are clear about the
you know you can always refer back
the video what we released before explaining about
the Johnson Cook material model and some significant application part
so from that background so now
we can know i can directly you know we can
directly start defining these parameters
This is exponent coefficient is 0.42.
So, M part I am going with 0 number and here we have
to say rate dependent and select the
Johnson Cook and for the C
parameter it is 0.0026,
epsilon.1, say ok, so this is done
now I will go for the
damage, Johnson Cook,
so DN is minus 0.77,
T2 is 1.45, T3 is 0.75,
0.47 and D4 is 0.001 and D5 none.
So guys just to remind you again.
So one of the point is in this tutorial
for this JRP impact I am considering the power law
that is the stress strain curve with the yield
and the modulus part and plus that is the plastic portion.
and along with the strain rate effect
so the temperature effect is been is not been considered
for this evaluation so maybe
in next tutorial i will explain you about the accounting for the
temperature effect as well
so for the for this tutorial it is restricted or it contains the the
the triaxial the triaxial stress state tri state
of stress that is through the v notch and then the
the power
law along
with the
strain
rate
effect
so this
is done
so now we'll
select the
anvil part
and then apply the steel properties
so this is for anvil this is uh it has very simple properties
modulus and the density is good enough
so there are several ways one one can model the impactor
so we can also model considering as a rigid body
and otherwise we can have this kind of the one i'm showing
With the steel properties.
So here I am deliberately putting
this mass density as 1 e raised to minus 6.
So it will represent approximately 1.5 kg
of mass of the impactor.
So as per your need you can always play around
with the velocity and the mass.
So which is you can directly take it
from your test requirements.
and then you can manipulate the the mass you require
and the velocity required for conducting
this simulation. so here i'm just demonstrating
how you can really play around with the parameters
to get
the the desired simulation
of the results for you. this is
done. so we'll define the section
that is anvil.
so have this
assembly done
and then we'll go
for the step
part. so this is
explicit dynamic. time period should
be two milliseconds should be fine.
so it is 0.002 so i'm
going to define the
surface to surface
contact between uh
the master that is
impactor surface to the the slave part
so for that i am preparing the surfaces so you can
just observe i think you may be familiar
as well if not you can go through all the steps
so i'm going
to show you
in assembly
look for
surfaces
so i'm going
to create
a surface
that is
master
of anvil
it's
done so
create
one more
surface
that is
slave
so now
we can
define
surface to surface contact explicit and then
select from it is a master continue and then
slave continue here you can
define the contact parameter
that is the friction
part tangential
so this is for penalty coefficient
of friction i'm going with 0.25 here let's say okay
So this is the contact
is done now let's mesh this part okay
so I will go by the first part that is
the sample one
for just hide
this one okay
so go to explicit
and here I'm going to
choose the enhanced hourglass control
and then followed by there is one more important step is
element deletion so yeah here it is so
element deletion so I'm going to say yes
deletion is going to occur depending upon
the the damage criteria what we define.
So yes, okay dismiss and
We'd
like
to
have
0.2. So for fine
mesh
and do it again.
Okay
for the rest
of the edges.
I will go for
0.8. So let me mesh
this part.
Okay, so this we got the
fine mesh at the center
and then followed
by the coarse at
the outer
so let me
to the meshing of the anvil as well so i'm going
to hide the sample part and i will let me bring
the anvil
part so here
also we would
like to have
a fine mesh
at this tip
portion 0.3
i'm going
with and then followed
by here 0.8 again okay i
would like to mesh this part
okay it is meshed all right yeah now i can show all right
so this is done
So now we'll apply the loads and boundary condition part.
So let's go to load and apply the
simply supported condition.
to the PC1. Continue.
I'm going to select, excuse me.
Excuse me.
So this is kind
of 40 millimeter.
This is U2 right.
This is another
boundary condition
that is for
this part. So only I'm going to concentrate the U1
and U3 that is X and Z, G direction and only U2 I'm
allow
with
initial
velocity
now we'll
apply
initial
velocity
initial
velocity
excuse
me U2
minus 2500 millimeter
per second okay
this is done and in step i need
to the output request
I will set up that as well, all right
so here I would like to have the output at exact time interval
phi u e raised to minus phi u
So this is also would like to see.
Integer must be 5 raised to minus 5.
Let me see this.
The expression does not evaluate an integer and must be corrected.
Okay.
Okay.
Okay.
So, now let's have the output as well.
Output request.
History output at the same frequency.
So, that will have control like what exactly we are looking at.
At what interval we are looking for.
Okay.
So, this is done.
so uh guys uh what we had uh you know let me recap what we have done
so we have built a geometry
we have positioned this part
and we have partitioned the the sample part to
make a provision for the the meshing
that is a fine mesh at the center and then followed by
the coarse mesh at the outer side
and then there is a partition required for applying
the simply supported boundary condition with the span of 40 millimeter
and the boundary conditions
For this impactor is all the translation degrees
of freedom in lateral direction has been restricted.
Only the translation in the velocity that is the impact direction
that is the Y direction is allowed. And of course
the Johnson Cook metal model with a damage evolution has been defined.
So now I think we are all set to submit the run for this model.
Continue, okay, and I'm going to submit.
So it will take a while.
To have the results for this model, let me
see whether how far we are going reference
and rate for Johnson Cook damage evolution must be greater than zero.
Okay.
All right.
All right.
So let me go back to the property part here.
Edit one.
Yep.
So I missed this point.
So we are all set to submit this job
and we already defined the strain rate part also.
Let me take a look.
So there is one more small problem.
Activities involved.
So we need to get this impactor and at the center.
So let me do that as well. That is
2 millimeter in Z direction.
Okay, let's submit it again.
I'm just rewriting it
so it will take a while
So guys, I have result to share.
So here you can I just loaded the ODB file to this
This, uh...
Harpie model what we have built and
I am just going through the
the contour plot that is stresses
so let's let us have the the animation files okay so that looks
good okay so here it is so we are we're done
with the simulation you can see the the impactor is
creating the fracture into the sample
and and as expected the this is you know the triggering point
that is a v notch point so from that the crack has initiated
and it is going all along this direction
so so this way you can visualize
and understand the the behavior of the sample under the impact load
Okay, and there is one more parameter you can always look
at is the internal energy part.
So here you can look at the internal energy plot. So you can see around
At this point, it starts, you know,
once it is hitting point of impactor and then slowly
the energy is being absorbed while it is being fractured
and then at the end it completely, it becomes two piece and there
is no any further energy absorption for this aluminum sample piece.
So, this is what I wanted to share.
Take you through from this tutorial. So I hope you understand all
the steps involved into this sharpie impact test and I
Suggest you to go through this video and try to follow all the
Thank you for watching
this method as per your requirement If you like
this video please go ahead
and like this
video and also recommend you to subscribe our channel
so that you can keep receiving
new videos from us.
Thank you.
Bye bye.

