How To Template & Shape A Custom Carpet Stair Runner

Repair house
9 followers
11 Video Views·Oct 29, 2026
AI Generated·May contain errors
Welcome, in today's video we're going to be explaining to you how
to shape and cut a custom runner like this one right here.
So your first job is deciding what size you need your runner to be.
As a general rule of thumb,
we use 100mm spacing from the side or the stringer.
So we're going to be starting on our straight run of stairs.
And what we're going to need to do is put some protection down,
so some tape to start marking.
So if you just set your tape measure to 100mm
and then we take our tape and put that in the middle.
It doesn't have to be exact.
And we're going to come over this bottom stair.
All the way down to the bottom
and we're going to do that on both sides. Right so before we go on
with our marking you're going to want
to get yourself a couple things. So we like to have
ourselves a 100 mil block like this one.
Any bit of wood you like cut to 100 mil and keep hold of
that. And another thing you're going to want
is a combination square like this one. So our first
job is to take that block that we told you to get,
sit it against our stringer
On the tread and mark along the side of it
so on this side you can see we've got ourselves a little
obstacle we've got the post
so we want to actually be measuring off the stringer not the post so if
we take our tape measure and we mark our 100 mil
and now that we've got our mark from our stringer
we can take our combination square
and extend that down to the nose so now that we've got the
width of our runner set for our straight run
of stairs we can now transfer those marks down.
Onto the next step. So for this side we can use
our block put it on that stringer again and just strike a line
And for this side where we've got a post
in the way we can use our combination square
and strike down off of the mark we made on top
so now that we've done that before we start
templating out for our winders we're going to make
a note of this measurement between the two points
because that is going to be the width
of the runner on our straight stairs
so i've took note of my measurement you should do the same
and make sure you keep it safe because
we're going to need that a little further in the video
so now that we've got all of our markings
and our width set for the winders
which are the ones that turn we're going to be using
craft paper to make templates for our runner.
So to get our measurements for how much to cut off
of our roll of craft paper,
on our winders, we stick our tape on our pencil marks
and square to the nose and measure down.
So we've got 600 mil.
So just over-cut it, so we'll take 700 millimeters off.
So if we just measure out 700 mil.
and we're then going to take some scissors and cut this off.
So once our paper's cut and ready to go
we're going to set it square with our nose
and make sure that we're definitely going to be covering the
edges for our runner. I'll start by creasing the back
and then I'll take some tape and stick it
into position temporarily. Now that it's stuck I'm just going
to take some of the excess off the back.
You can either use a Stanley or your scissors.
So now the next step is to put some tension on the front
and then tape that down.
So now that it's in position, we take our block
and then we're just going to scrub along this side here
using our block all the way to the end.
We then transfer our marks down onto
the face using our combination square.
And now for this side, we're going to make a little cut along
our paper to expose the mark that's on the back.
And we'll just cut the waste off.
So now we can transfer that onto our templating paper.
Right before we go any further let's get
the rest of our craft paper stuck down to our winders
and our quarter landing. Right so that's
all of our templating paper fixed down ready to be marked.
So we're going to continue around this
outside edge with our hundred mil block just marking off
of our stringer. We're going to do
that all the way up to the noses including our small quarter landing.
And now we're going to take our combination square
and take the line from the bottom
up the front and over the nose.
So what you might find which is very common is this line
and the one coming up the front do not line up on your winders.
So all we do once we're up to
the nose here and here we just take our square
and then we're just going to meet
two lines together.
So if I mark that and you'll see that that's how we keep.
our gaps right
so that's the stringer side all marked out with our block
all the way down to the floor now we can move on to the post side right
so our next step is
remember that measurement i told you to take down
at the very beginning of the video we
now want to be marking from this line across
the width that you wrote for us it was 625
So we're going to mark that on the opposite side.
We're then going to take our combination square
and make that line long enough to get past our post.
That can now be sent down to the floor.
We're then going to do that same measurement
on the bottom of this step.
And then if we place our combination square up against this riser,
we can now pull a line back across.
And you should end up with this little detail.
around your post and now from this bottom one we can extend
that line up onto our winder and then
from the nose back to our next winder
and then we're going to do the same again from this point
up and now that we're onto this winder we're going
to transfer the measurement from our
newel to there from here to here
and we'll just use the straight edge to make sure we're parallel
along the post and put ourselves a line so now you'll see that this gap
and this gap are now the same
and then on the step above we're going to come off that riser
and do another square line
so now we've got two parallel lines around our newel and our
last measurement is the angle from the post
to there for us that's 70 mil we're going to
do the same up here and then we're going to take our combination square
and strike up the riser
and now we're just going to extend our lines until they intersect
so that one goes there
And this one goes.
And the reason we do all of this working out here
is because visually we've got a uniform gap
all the way down around our post.
So before we remove these, now that they're all marked,
there's a couple of markings we wanna put on this paper
for us to transfer to our carpet.
So here we're gonna be writing top.
W for winder and then one.
Now you can count from the top
or you can count from the bottom.
For us, we like to count from the top.
And then we wanna mark our pile direction.
So if we put an arrow for down and then write pile.
And the last step we wanna do
is to mark where we want our binding.
So if we just do arrows like this.
Because we want binding down all these edges,
but we don't want binding across the top.
Now, this may seem like a bit of a stupid step,
but when you take this off,
it is very easy to get confused
about what's happening with what.
So now that we're all marked up,
we're gonna take it off and start cutting along our lines.
So make sure you take your time with this,
because obviously this is gonna reflect
directly onto your carpet.
So don't go rushing your cuts, take your time.
This little extra section that we've got at the top
and the bottom leave those on because they're
going to help when it comes to fitting the carpet.
So that's what we're left with we're going to do
exactly the same thing on each of these templates
and then we're going to put them to one side
and move on to the last step
and that is to measure how much carpet we need for that straight
run of stairs that we took the measurement for.
How we do that we take our tape measure
we take our measurement by folding it inside
of the creases of each stair hold it
And go on to the next, hold it, go on to the next,
all the way down and to the top of that first winder.
Right, so we've done all our templating, we've took our measurements
and we're now at the piece of carpet we're going to be cutting.
We've come to a good friend of ours,
Russell, and he does binding and whipping,
and he's going to talk to you about
a few different methods you can use to cut your carpets down.
So shaping a staircase is pretty easy for us fitters,
but there's different tools that you can use.
Obviously a straight knife
but have something underneath the carpet to protect the floor
if you're confident enough to cut
a straight line with a straight knife.
If you're not, use some scissors.
It takes takes you time to do it but at the end of the day
it will be very accurate.
We already know our measurement which is 62 and a half.
And just get your shears and follow the design
and just go slowly or as fast as you feel comfortable at.
With this design, we can easily spot it
because we deal with it day in day out.
But if you're a novice or never done it before,
what you can do, you can just mark it with a marker just
so you know where you're going to hit the design.
And then if you want to go buy yourself a tool,
these are about £10, £15 on any online flooring shop.
And these ones are around about 40 to 50 pounds.
These are the ones that we use as a professional.
These are more of a DIY cutter, but it does the same job.
Right, so when row finding a plain carpet,
you can do it in different ways with different tools.
I like to use a braddle.
A braddle just opens up the pile and most carpets have a line to it
and it will stay to that line, stay true.
You can actually buy the exact tools for it,
these again are about £10 on most flooring sites.
You've got this, this is the comb, you get this from the States.
Again this opens up the pile and
all you do is go back and forth and it follows the pile.
So now we've done that, the purpose of that
is to open up the pile so we've got a clean line to cut through
and with our cutters you can just
easily go through with it.
With binding and whipping you can actually mark on top of the carpet
it doesn't affect us because we're actually covering
the mark that you're going to create so
all I'm doing is just following the design with a ruler
and a pen and I can cut to that with some
shears a straight knife or even with my cutter
which will make it a lot easier visibly to see.
And if you notice what I'm doing,
I'm putting my hand behind the cutter keeping the carpet flat
and taut and then as I'm pushing through it makes it
a lot easier to cut the carpet.
straight and true. So now that Russ
or Russell has shown you how to cut our straights and some
of the different tools you can use we're now going
to look at the templates we made. So what we're
going to be doing is sitting them on top of the carpet like
so and because we're using a pattern
carpet we've got an extra line on our template
and that is the nose of where our design ends.
We line that line up with our design.
We're then going to take our pen and mark around our template
and it's at this stage we want to
take super duper care to line our pattern up with our template
because when it's cut and bound
this is when it will show.
So we want to make sure we've got our design nice and square. If you've
got a pile you want to concentrate
on the pile direction that's why we put that arrow
back when we was on the stairs. So that's our marks.
and just remember when you're looking at our treads
or our winders this section here is the
part that goes up so this is why we want it super straight
because if you go off the carpet's not
going to look right going up your risers right
so we're going to start cutting this out we've
got proper carpet shears
but you can get away with using normal scissors if you want to so
we're just going to follow the marks that we've put on our carpet
and one last step once we've
Once we've got it cut,
is to transfer our binding marks that we put on our template.
So we're going to turn it on to its back and put some arrows.
We rushed you off a little bit there at the end because the weather
come in and got us.
But if we have missed anything, chuck us a comment below
and we will tell you whatever it is you think we might have missed.
This is installed.
And don't worry, we have got a full video
on the actual installation of this.
So click the link and give it a watch
and we'll see you on the next one.
