💲With the NIJ 07 protocol and CPL finally upon us, many armor companies are starting to produce designs that they will start CPLing or listing under the new RF ratings. The original Gen 1 1155 was a single (and later multi) curve Alumina/Eglass NIJ 06 CPL Level IV plate. Stopping M2AP and a slew of other lesser threats. Due to what many feel was a botched FIT, it was removed from the CPL. RMA has since launched Generation 2 variants of their armor using stronger, thinner and lighter strike faces. The 1155 is offered in 10"x12" and SAPI sizing and is multi-curve. This demonstration tests the limits of the design with various threats like M2AP, M855A1, M193, M855
This demonstration pertains only to the specific samples tested and may not be used to claim product certification, approval, or endorsement by NVLAP, NIST, or any federal government agency. Always refer to official NIJ-accredited laboratory reports for threat profiles.
—
The information presented in this video is technical and educational in nature. All safety precautions were followed. Any imitation or use of information demonstrated is done AT YOUR OWN RISK. This video is not an attempt to sell goods or services. I am not a gun shop and do not sell firearms, parts, or magazines. All such activities are regulated and subject to applicable laws.
plate number two is strapped in and ready
to go we have a few treats from Sugarfoot Outdoors we
have been waiting to test these for some test subjects
and i figured this would be
a good baseline hey everyone welcome back
to the range my name is Matt Olson
king of Armor Destruction Armor Wizard zap zap hot off
the freaking presses from RMA
they released these in 2026 we did
the 1165 gen 2 now today we've got the 1155 gen 2
This is a NIJ 0607 Level 4 or RF3 plate.
Let's show this guy on the table
and talk about what we're going to do today.
Now, on full transparency, RMA Armament sent
these 1155 Gen 2s over for me to review with no strings attached.
I do have an active affiliate with them,
meaning that if I have a link in the description below
and you have made the decision to purchase these on your own accord
and you want to say thank you to the channel
for all this hard work that we put in,
that's what those links are for.
I put all that back into the channel
by buying different types of armor.
or ammunition or different materials to get this job done.
So as I mentioned the 1155 Gen 2 is the
new variant of the original 1155.
As of making this video these are not NIJ certified meaning
that there's a giant list that NIJ keeps
and effectively it's a quality assurance you know
program that the NIJ uses so that when you roll off serial number one
and all these specifications
Serial number 10,000 is going to remain the same.
This level four plate is multi-curved.
It is a sappy medium, so we measured this
at 9.252 inches by 12.20, so very close
to that nine and a half by 12 and a half.
It is 7.485 pounds, or 3.39 kilograms.
It is very thin at 960 thousandths, or 24.40 millimeters.
As I mentioned it is multi-curved
so this is a sappy cut so we've got that curve there
and we also have a curve here and then usually
these little leading edges have a curve there
and what that ends up translating to is it's going
to fit your body a lot tighter than a single curve
or no curve so that usually what I've noticed
is it takes a lot of that weight off the shoulders
when you're wearing these around all day long.
If this is the first time you're using my YouTube
channel we do all our body armor demos completely
different than everyone else on YouTube. We're
We're after worst case scenario.
Rewind that and say it again.
We're after.
Worst case scenario.
Since this is rifle armor, we shoot at 45 feet.
We also shoot at zero degrees, again,
because that is worst case scenario.
Finally, we put a spreadsheet here at the beginning and the end.
We kind of foreshadow all the threats that we're going to shoot at it.
We mark our velocities and our pass-throughs.
In the end, we do a fan favor.
That's a teardown where we get to look at the guts of the plates.
I do want to remind everyone that I am not an NIJ lab,
so if you see a threat stopped or passed through,
you should always defer to the manufacturer to produce accredited,
recent, and frequent lab tests
showing that those threats are stopped.
Pop it on the flip side.
If you're the manufacturer and you see some kind
of weird threat stop, you should send
that off to the lab and have that added
as a special rifle threat to your panel.
One final caveat is, again, I'm a guy out here on the woods.
I'm stretching my dollars as thin as possible.
Sometimes I can get two plates, sometimes I can get four.
So I have to take as many shots on a plate as possible.
You know, I try to maintain that NIJ shot distance
of at least two inches from each
shot.
So if you see a pass through on the seventh or eighth shot,
don't always assume that that
plate is garbage.
Plate number one is strapped in and ready to go.
And since this is level four,
we'll go right to that threat specification.
That is our M2AP, normally in .30-06.
I have it loaded in .308 with a 24 inch barrel
to get to the specified velocity of 2880 feet per second,
plus or minus 30,
2912, 2908, 2939.
And turn around. All right easy enough shots number one two
and three per our NIJ standards
level four our RF3 only has to stop one round.
So we put three on there and depending on which
chronograph you believe we were either in spec or slightly over it.
We can never seem to win
with those loads. I get one dialed in and then there's
a temperature variance and then they
pick up a little bit of speed. Place those bets and comments below.
Oh Raggy only one pass through.
On that third shot down there in the corner,
now you could argue that is pretty close to the edge.
It should be two inches, but that guy was stopped,
and then our first shot was stopped.
Now as far as back face goes, try to get in there.
I still am looking to build some kind of rig to hold this,
but that one was 30 millimeters,
and that one in the middle.
Was right around 17. There's not even a dimple in the plate.
I mean there's a little bit of one for
there. So it looks like RMA on the 1155 is using the e-glass still
and that does a pretty good job
at controlling back face. All right time
to see how multi-hit capable this plate is. We've stacked
330 caliber threats on there
so now we're going to 556 this is a 22 inch tc compass
with our tuning cans 556 long up front
so we've got three flavors of choice for 556
we have m193 m855 ss109
and m855 a1 epr it's getting kind of hard to find these days
m193 number
one two three
and then four
then our m855
ss109 number
one two
three and then four and our m855a1 number one two three
and then four now some of these
are in close proximity to each other place those bets
in the comments below as i whip myself with
these straps oh raggy we only have
two pass-throughs from this plate
and that was the shot
of M855A1 that was close to the M2AP pass-through
and then that shot right there which was
about two inches from that shot.
So that was a compromised area, but very impressive. So we've
got 12, 15 shots on a plate and only three pass-throughs.
That is very, very amazing for
what's considered a budget-oriented plate.
I do hope that RMA seeks NIJ CPL for this
and it gets it because it will be one
of the best bang for buck made in the USA.
multi-curve level four plates out there
that's under eight pounds frankly with a true edge
to edge right face and very true to size none
of the lightning cuts in the corner i do think
they offer that in a shooter's cut
but pretty darn amazing if i do say so myself let's move
on to plate number two now in terms of any back face there
is not a lot to write home about i did
beat this flat on the way to this one and
That shot of M855, 23 millimeters,
and that's being a little very generous there.
Very, very controlled back face when it comes to
5.56 frags for the level four plate.
Plate number two is strapped in and ready to go.
We have a few treats from Sugarfoot Outdoors.
We have been waiting to test these for some test subjects,
and I figured this would be a good baseline.
This guy is a 130-grain S7 tool steel tipped round,
and then this guy here is a tungsten copper alloy mix,
right around 160 grains.
We brought out the 24-inch Savage 110 again.
All right, time for the U.S. Army, U.S. military's new hotness.
This is the NGSW caliber, 6.8 by 51 millimeters, or .277 SIG Fury.
This is a hybrid case, pressures up to and over supported 80,000 PSI.
This is the 20-inch SIG Cross.
This is our Gen 1 or original variant of the 120-grain EPR,
also known as XM1186.
76
Now for this guy we're going to reduce the charge on it
so to simulate a little bit of range.
All right we'll finish the plate out with our 5.56 threat
but we've increased the core hardness to
some tungsten.
This is some Ruag 62 grain with a tungsten front end in it.
The entire core is
not tungsten so we'll go right hand side.
Our tungsten copper 160 grain
was right there.
the s7 tool steel 130 grain was right there
then the xm 1186 full charge was right there
they reduced charges right there then our tungsten core threats
and 556 number one two and three
place those bets in the comments below
oh raggy we had confirmed pass-throughs
from both of our 6.8
As well as that tungsten core threat right there.
Now, you could argue because we compromised the area right here
because of how crack propagation works in this area.
But this was probably a pretty bad area for that to stop.
But it stopped both of them on this side.
And again, that is something that it's not rated for.
Now, that 130 grain did a number on the corner of that plate, though.
Blew it all to the kingdom come.
But that copper tungsten matrix mix 308 round did not make it through.
Our 6.8, that smoked that guy right there.
And again, I think this has
to do with the material being this e-glass stuff.
If there's any part of that projectile left that that ceramic
strike face did not degrade, destroy, or turn on its side,
it's still hardened steel, and it can't stop that as well.
And that XM1186, that steel portion of that round is very, very long.
Now, we'll double check on this one.
on the bottom one but that definitely looked
like it squeaked through maybe on the side
because we didn't beat all this flat and there was a hole right there
and now for a fan favorite the teardown
that's where we get to look at the guts of our plates
we check for any pass-throughs you guys get
to see what kind of materials make up these
plates to see how that magic works how
a you know eight pound piece of material
is able to stop bullets in excess of 3,000 feet per second
so here was plate number two
We are using a drop face foam.
measured at right around 200 thousandths thick. It's pretty much that
industry standard foam.
It gets a little on the firm side when it's cold, but it does a really
good job at keeping that strike face from cracking when dropped.
We do confirm that this strike face
is not laminated on the front side.
Usually we see some type of, you know, adhesive and a material
like Kevlar or more of the backing material
that's basically used to laminate the front so
So that if you get a hit up here, it kind of keeps the ceramic
together so we didn't notice any of that on the 1155 G2
It is a budget plate and that you know is time
and money. So there is our cover
and here is the back confirmed the only pass-throughs were the
XM 1186 at full speed and that reduced pressure one
and if you look at that it's almost like what
was left of that steel tip was going sideways
and that one round of our tungsten 62 grain 5.56
So this is our e-glass backer.
We measure that right around 350 thousandths thick and I borrow
about 350. You can see that it's pressed
and still maintaining its shape even after taking
some of those 30 cal threats
I like that RMA offers or adds the foam protectant on the outside
edge of the strike face and the backing.
Now this isn't the reduced foam edge that I talk
I talk about this is on the outer perimeter
Then here is our strike face.
I measured that right around 330 thousandths. You can see on how
those shots crack that ceramic
and again as I mentioned it is not laminated but I would say
for not being laminated whatever ceramic RMA is using in this gen 2
It's holding up a lot better than the original Gen 1
because that would actually break off in sections
This one isn't doing that.
Then we get to plate number one,
and obviously we put more shots on that plate
so the strike face is not doing too hot,
but there's actually still quite a bit of large pieces from it
You can look at that cool crack propagation from the M2AP
and how that ceramic has to degrade that projectile core.
Then the only pass-throughs on this one,
We're the M2 AP shot number three down here in the corner,
and then those two shots of M855A1.
Overall, pretty good constructed plate.
I will say, if we could offer any constructive criticism,
it would be to obviously laminate the front side of the plate,
but that's going to add cost, but maybe add
a little better adhesion between our backer and our strike face,
because normally with the RMA plates, I can run my...
knife around the outer perimeter with that cover
and then easily peel the two apart again obviously
that's after i shot it but with all that being said
that's all i got for you for the RMA 1155 G2
i'd say this is a definite upgrade over
the G1 it does run a little more cost 2026 wise than what
the original 1155 was running i really hope
that RMA will CPL list this because it's going to go
I'm going to go on my list as one of the.
Best budget-oriented level 4 plates,
considering it's under 8 pounds, it's multi-curve, and it can
stop at least two M2APs, possibly even more,
and pretty much all of your 5.56 threats from the
longest barrel that that's possible from.
Well, folks, let me know in the comments below your
thoughts on how our 1155 Gen 2 from RMA turned out.
I personally think this is a valid upgrade
Over the Gen 1, we are lighter and thinner.
thinner than the original plate
and our strike face seems to hold up a lot better even though
that it wasn't laminated.
Now our alumina oxide ceramic has to be thicker
and it obviously weighs more than our B4C
or our silicon carbide
but I think it offers that good blend of weight versus thickness
versus performance when we start shooting some
of those obscure threats at it.
Alumina tends to do pretty darn well.
Our silicon carbide and boron carbide will always live in that place.
Place where you're looking for that high speed,
low drag plates.
And obviously that's gonna bring a lot of cost.
Overall, for where this plate was built to compete
in that budget space,
I think this is gonna be very hard to beat,
mainly because it's multi-curve
and because it's under seven and a half pounds
for an ESAPI size medium plate that, you know,
otherwise those 10 by 12 plates,
some of them cut the corners off of them
and that's how they get some of that weight savings
because they're not getting any more ceramic.
So this plate's gonna be very hard to beat.
I do believe RMA is going to CPL this plate,
and I hope they do.
That will, you know, add some confidence level
to consumers and or buyers
knowing that that extra step has gone through.
So the NIJ can say without a doubt
that it will stop M2AP from serial number one
to serial number whatever many millions that they build.
With all that being said,
it's time for me to get the heck out of here.
But at the end of all my videos,
I take a moment to thank all those
who helped make these possible
because there's a lot that goes into this stuff.
Number one is my family.
A big thank you to Amy and Deacon.
They are out here helping me any time they can get,
either from pulling a trigger or
helping me take care of landscaping stuff or anything else.
A big thank you to them.
Family, as always, first, Deacon would like
to remind you all to like and subscribe and
share these videos so the algorithm can work for us
and not against us, especially in 2026.
YouTube reset all the algorithms and everything,
and I have a hard time gaining subscribers
and or even getting views on some of this.
You know, niche content stuff that I'm well known for.
So any of that is greatly appreciated.
Number two are my Patreon and YouTube channel members.
I have my Patreon link in the descriptions below.
So if you're looking to give back to the channel in any way
or this data that I've given you basically for free,
that's what those links are there for.
You know, I got to buy tiki torch fuel to keep the mosquitoes away
or I'm buying straps.
or procuring different types of bullets
because some of that stuff is hard to get so all that
is greatly appreciated. Number three are the fine folks over
at RMA Armament Blake and Corey sent
me these 1155 G2 plates to destroy with no strings attached.
As mentioned I have an affiliate set up
with them so if you're looking to make
this purchase I do have a discount code Buffman
that knocks a little bit of that off there
and saves you some cheddar. Number four are the fine
folks over at Sugarfoot Outdoors they have some pretty sweet treats
and wild interesting designs
And for number five thank you all for watching
Until next time, I'll catch you at the range.
Look at that five o'clock shadow.
It's time to shave.
Good night.
So we use a giant clay briefcase filled with Roma plastilina,
number one clay from Chavant that acts as our compressible media to put
the body armor up against. And it's the same clay that NIJ uses.
But again, we're out here in the woods.
It's a representation of what the NIJ could expect.
They get to heat theirs in an oven
and they're only allowed to take it out for an hour.
By the time I take mine out of my little igloo and bring it down here,
it's already cooled off.
So if you see something like 50 to 60 millimeters in my clay,
likely in the NIJ's eyes, that could be failing. We use a
We use a chronograph whenever possible.
We have our Pro Chrono Pal Digital DLX as well
as our Garmin Zero C1 and our Athlon Optics
Rangecraft chronographs.
We've got three data sets there.
So if one of them fails, we hopefully have two out of the three.
Sometimes all three of them like to fail.
Since this employs a ceramic strike face per the NIJ,
we've gone ahead and dropped each
plate on its face two times as a preconditioning test.
The NIJ-06 and 07 drop standard are exactly the same.
I actually paid like $85 to have a PDF
that tells me that they're the same.
After we've done that, we mark each plate with a DT,
indicating that we've run the drop
test, and if we do it more than two times,
we mark that with a parenthesis.
Then we do a torque test.
That's where we grab the opposing edges
of the plate and listen for any cracks.
If we don't hear any, we mark that with a TQ.
As far as I can tell, this 1155 Gen 2 plate employs
a complete edge-to-edge strike face,
meaning for this 12 1/4 by 9.25 dimensions,
that strike face leads almost all the way out the edge of the plate.
Some places will sell you a lighter plate
because they're giving you less ceramic
because the NIJ won't shoot any closer than 2 inches from the edge,
so it's good that this is complete edge-to-edge.