In this video, experienced lapidary, Steve Moriarty takes on the challenge of faceting a rare 625-carat non-hydrophane Ethiopian opal—a stone that is rarely faceted due to its unique properties. Watch as Steve meticulously removes inclusions and fractures, shaping the rough stone into a stunning 198-carat faceted gem. Despite its instability when exposed to air, this opal's incredible transparency and Steve's expert craftsmanship result in a breathtaking piece, perfect for any serious collector. Witness the transformation of this opal from raw to refined, showcasing the beauty hidden within.
Also, if you're loving what you see with this stunning Ethiopian Opal, you'll definitely want to check out MoreGems.com. We've got an amazing selection with a wide variety of gemstones that we've cut and collected from around the world. If you're not ready to go shopping, feel free to subscribe to our channel, because we've got a ton of videos about all sorts of gems and jewelry – it’s like a treasure trove of sparkly knowledge! If that sparks your interest, you've got to catch our Live MoreGems Show, it's our monthly live streaming event where we release many of our newest cut colored gemstones. It's super fun, and you get to see all the new gems we've got, learn some neat stuff from the pros, and maybe even find your next favorite gem. It's not just a show; it’s a whole experience. So, come hang out with us and dive into the awesome world of gems – where amazing beauty and top-notch craftsmanship are always the stars of the show!
Disclosure: Some of the links in this video’s description are affiliate links. If you click and make a purchase, we may earn a commission at no extra cost to you. We also feature products from our own family jewelry business. Thank you for supporting our channel and helping us continue to share our passion for gemstones and jewelry.
This is a 625 carat willow Ethiopian opal. It's a non-hydrophane variety, which is a little
different from the opals you've seen from us, and it presents some challenges for cutting,
which you'll see as we proceed. This is a very highly transparent gem, has some beautiful colors
in it that I hope the fastening will reflect throughout this stone. So this being a non-hydrophane
opal, it does have the problem of you can't leave it out. It's got to be kept wet. So it's pretty
much a stone that we're going to cut and show you and then it goes into some moist atmosphere
and you can take it out and show it, but it's never going to be a piece of jewelry. But hopefully
it's just going to finish out a really remarkable gem. So I'm going to work on pre-forming it now
and get its basic shape, get some of the excess material out of it, and then top it up and we'll
start fastening. So right now I'm just trying to get the girdle outline of this. It looks like it's
going to be kind of like an antique cushion, kind of rounded on both sides. So you've got
things to deal with like low areas here and just got to make an even girdle line all the way around
the stone. Our color down here, that's pretty green through most of the stone. So those of
you that are curious what I'm cutting with, this is a 360 grit diamond lap. I don't want to use
coarser just in case I could cause damage to the opal, which is always a risk.
So I'm just trying to get this material out of the crown and I have a fracture over here I have
to deal with. So hopefully lowering the crown and then cutting this in will get that to the point
that once I start fastening it will naturally take that fracture out.
So here's our preform, which is basically an antique cushion, probably a step cut antique
cushion. And I've gotten most of the imperfection out. There's still a little one here in the table
that I'll take out later, but I think the shape of the preform is really good. So we'll get really
good yield from this, but I had to remove a lot, particularly to get that inclusion out right in
the middle of the table. So I'm going to mark this and try and locate the center with the dop.
So that'll give me a fairly close to center. So I've got that pretty darn close to center,
I believe. So we're gonna see if I can keep it in place here. Do this and recheck it.
Now let me double check my measurements. Looks good. So get the appropriate size dop.
This is not the actual transfer block for the Ultratech V5, but this stone's just too big for
I think to fit in here. So we'll mix up our glue and get this dopped up and
get it back in a wet cloth to keep this non-hydrophane opal moist. We have had experience
in the past where this type of material does craze. Even though we bought it in a dry state,
we've had bad experience with this. So we'll discuss a non-hydrophane opal a little bit later.
Looks like that should be enough glue. So you see that I only glue around the dop. I don't
glue under it. Just as you'll see later, it's a much easier release of the stone.
Doesn't require any heat then, which I try to avoid heat as much as possible. I'll just
cut the glue loose around it and hopefully the opal will fall right off the dop then.
You'll see that later. So we've dopped this opal up and in the process I'm trying to keep this
opal moist because of issues I'll talk about shortly and getting the epoxy to dry. I find
out that epoxy has to be in a low moisture atmosphere to solidify. So I just wrapped the
opal in a wet rag and just had a method to keep it wet overnight and I think the epoxy solidified
okay. So we're ready to take this out of the transfer block and get it into the Ultratech V5.
So let me explain a little bit about the issues with this opal and why we keep it moist. This
actually was sold to us in a dry state but that's the same as this opal was sold to us in a dry
state and told that it would be stable. But as you can see the surface probably down to only
half a millimeter is just cracked up. You know this took a couple of months for this to happen
but it did finally crack up and the assumption is if you recut it you'll get the same
surface reaction. One day I'll at least pre-form it and take all those cracks out and see if it
actually does eventually become an opal that won't craze but I'm assuming it'll just continue
to craze. So that's the same situation with this opal. So we will keep it in a moist atmosphere
to try and prevent that. So it's not good for jewelry. It's only good for really a collector
and you know and you can take it out of the water and you know probably for you know I don't know
how long but for at least hours and view it and you know maybe even weeks. But we're not going to
take that risk. So we're going to cut it. We're going to keep it moist and let's get started.
And I'm going to cut this into an anti-cushion probably a step cut. So the first step is going
to be to cut the girdle of this gem. So currently I think it was 412 carats. So we'll see what we
end up. I've got a good pre-form so I don't think we're going to break that 300 carat mark but
it'll be a big one anyway. The biggest I've ever cut. So I'm going to start with the girdle. So
we're going to set the Ultratech V5 to 90 degrees and try and figure out what my girdle outline
was going to be. I think I'm going to go like one to either side, three and six to either side on
this side and maybe one to either side. I don't know. We'll see what works. So one thing I always
do is look for where my issues are that you have to deal with and currently would be this little
bit of low area here and probably this corner. So you do want to confront those fairly quickly
otherwise you're going to just have to recut everything to get these issues out of the way.
So I'll start with this corner and see if I can get this up a little higher to where I have a
girdle where that chip is now. So I cut into this problem area and I got it to the point that I think
there's enough crown and when I cut the Q it will, the rest of that little chip out will
disappear. So once I cut that I went around and I matched the four matching facets, cut them to the
same depth. So the girdle is all cut in. I've cut this side plus zero, two, four and six and on this
side it's plus two, plus four and plus eight. So here it's on the zero or 24 and then plus two is
the next step and plus four index and plus six. That's all in so now I'm going to start forming
a Q it. I'll cut this opal. I'm going to try 45 degrees, low refractive index material so
you need a higher angle. So we'll start the Q it at 45 degrees. So I've established a Q it.
So now I'm going to go, I'm going to make three steps in a step cut. I'm going to go to the third
step which is the girdle breaks and I'm going to cut somewhere close to halfway up this and
then I'll put the middle row in later. Actually finish the the Q it row. I'll probably do the
Q it row second and then put the third row in last. So now I'm going to establish where the
girdle is going to be with this next row of facets. This girdle step row, the third row
is finished. Now I'm going to go up and I'm going to finish off the Q it row and then I'll put the
middle row in. So I just ended up having to recut the entire work that I'd done
because I couldn't close the Q it. There was a part of the Q it that just wasn't cut deep enough
so I had to cut a lot deeper, probably lost 30 carats, but ended up being that the fracture
we talked about earlier wouldn't have come out anyway the way I was cutting it. So once I closed
the Q it and came back and recut everything it works out that I just got rid of that fracture
which you can see down there towards the bottom and it just kind of came out perfectly. So all my
cussing about having to recut the stone probably was in vain because I would have had to recut it
anyway if I hadn't had that problem. So just one of the things you run into in cutting stones,
particularly big stones. So I've cut the Q it row at 44 and the girdle break at 56 so now I'm
going to cut the row right down the middle and that'll be halfway in between which is going to be
something like, well it's going to be 50.
So we're finished cutting the pavilion and now I'm going to move to a pre-polish which my
pre-polish is actually we're going from a 360 diamond lap actually to a lightning lap and this
is a 600 grit. This is actually my pre-polish and from here we'll go on the polish. So we're all
finished pre-polishing the stone and we'll move on to polishing. I think I'm going to hold off
till tomorrow. This stone has kind of worn me out. These big stones take a lot of time and
when you've got to cut them twice it makes it a little more difficult. So tomorrow we'll
move on to the polishing. I'm ready to final polish this large opal and what we're using to polish
are these spectra laps. They're cerium oxide is what's impregnated into them so we put it on a
master lap and one thing I do different with these spectra laps is occasionally I'll add
cerium oxide to it. This is a paste of cerium oxide. I think this is super cerium that comes
from Kingsley North. So I take a little dab of it and put it here in the middle.
Move my water out just a little bit and start it just very slowly and the idea,
I don't want my finger there, is when I need cerium oxide I can just drag a little bit out
into the cutting or the polishing zone out here and it works much quicker and it'll make this lap
last a lot longer. Now these facets are pretty large so it does take a while to polish
and I use my finger to keep the cerium oxide from blowing off the lap as the water drips
and that's pretty much what it takes to polish one facet. So one more facet left and we're
finished polishing the pavilion of this opal. Then I'll transfer and we'll go to cutting the crown.
Okay we're transferring so we can cut the crown of the stone. I will mix up the glue and I've got a
v-dop here on the pavilion of the stone and I'll glue around the dop. I'm not going to glue under
the dop just to make it easier to remove. Then we'll let it seal up and we'll remove the other
dop and start cutting. So we've got our opal transferred and the glue seems solid so now
we're going to take it out of here and I have to remove this dop. So I only glued around the dop
so I should be able to heat my knife and just pick this off and it should fall off hopefully.
So this crown will be a step cut and I'll cut three steps and I'm probably, because I don't
have a lot of crown height, I'm going to start at 40 30 20. I have a little inclusion in here to deal
with. The cut through looks fairly deep so I'm probably going to end up re-cutting the girdle.
Unfortunately on a step cut it doesn't affect the pavilion I've already cut. I'll just cut
into that first step a little bit. So we'll see what we need. I'll start by cutting 40 degrees
and get to it or a girdle line. So I pre-formed the top of this a little bit so it'd be easier
to work on this large table trying to get that inclusion out and it's pretty deep so I'm
probably, once I get that out, I'll probably have to cut the girdle in a little bit so I have
enough crown to close that table up some. So the inclusion's out. I'll try and figure out whether
I need to cut the girdle in. Probably will just to get enough material to get this table much
smaller. So the facets are mostly in. You know you can see this little divot here. That's the fracture.
That's what's left of it. So it's almost out so I'm gonna go to a pre-polish with my 1200 lap,
re-cut the girdle a little bit and re-cut all this and this should disappear and hopefully
I'll get the table a little closer to 50 percent width. All right we can move on to the final polish.
As you've seen me in the past often I will, I cut the table on this vertical and often I would
polish the table just putting the machine vertical and polishing on here but with a table as big as
this is that's not going to be easy to do so I'm going to do as the machine recommends and that's
actually use a 45 degree table adapter and to do that we'll remove the stone
and remove this screw that holds the stone and there's conveniently
there's a little place for it here so you don't lose it and put that on 96.
Now we're going to set this to go to 45 so it's at 45 degrees. I'm flat on the lap
so now I'm going to tighten this down so now I'm ready for the stone. Tighten it into the machine
and then we'll be back at 45 and we can start adjusting it try and find exactly where the
table is at. So as opposed to the way I usually polish which is vertical at 90 degrees this at
45 degrees the big benefit here is you get more adjustments to hit that table perfectly. Often
when I'm cutting vertically at 90 degrees polishing the table I'll have to polish a
little more because it starts from a little bit towards one side
which without that extra adjustments that you have so now you've got
rotational and vertical adjustments so you can find the table exactly like this and when the
table is as big as it is this is really what you have to do and which is actually what's recommended
by the machine and the purpose of this 45 adapter. So let's get on the polishing this is always the
toughest part of cutting the stones and this is a huge table so I expect to have some difficulties.
Be gentle. So you can see it looks like I may be getting right on where I need to be and just need
to go a lot further. Well hooray it's over what a nightmare that was. An hour and a half to get
this table polished. I don't know what was the problem I just kept scratching scratching
scratching but we're done and hopefully it'll be a great one we'll see in the next couple of days.
I'm gonna let it set overnight and then we'll try and get the glue off tomorrow and
and hopefully by next week we'll know what we've got. Well should be some interesting colors coming
out of it I think it's going to be a beauty. Wish it was completely stable this would be one
valuable piece. Here it is 198 carat willow Ethiopian opal faceted a mystical beauty with
the colors floating within. You know the only issue with this material is it's not completely
stable so you do have to store it in a moist atmosphere. I mean you can have it out and look
at it for hours but when you put it away it's got to be continuously in a moist atmosphere you may
risk the possibility of it crazing and crazing is usually just on the surface but it does damage
the opal and this is too beautiful of a thing to take the risk to damage. I want to thank you for
watching this video on faceting this willow Ethiopian opal. Stay tuned for more videos
and I'm Steve Moriarty from MoreGems.com