It’s almost Valentine’s Day. This year, instead of giving her a rose bouquet, I wanted to express my love by gifting her an electronic breathing heart. This is yet another "cheap DIY kit" intended for educational purpose. There are a few variations of the breathing LED projects with similar setup, however the one with blue LEDs attracted me a lot.
Thanks ------ Thanks again for checking my post. I hope it helps you. If you want to support me subscribe to my YouTube Channel: https://www.youtube.com/user/tarantula3
Support My Work: BTC: 1M1PdxVxSTPLoMK91XnvEPksVuAa4J4dDp LTC: MQFkVkWimYngMwp5SMuSbMP4ADStjysstm DOGE: DDe7Fws24zf7acZevoT8uERnmisiHwR5st ETH: 0x939aa4e13ecb4b46663c8017986abc0d204cde60 BAT: 0x939aa4e13ecb4b46663c8017986abc0d204cde60 LBC: bZ8ANEJFsd2MNFfpoxBhtFNPboh7PmD7M2
Thanks, ca again in my next tutorial.
It's almost Valentine's Day. This year, instead of giving her a rose bouquet,
I wanted to express my love by gifting her an electronic breathing heart.
This is yet another cheap DIY kit intended for educational purpose.
There are a few variations of the breathing LED project with similar setup.
However, the one with the blue LEDs attracted me a lot.
This video is sponsored by PCBWay. PCBWay specializes in manufacturing of very high
quality, low volume, colored PCBs at a very budgetary price.
In addition to standard PCBs, you can order advanced PCBs, aluminum PCBs, rigid flex PCBs.
They also provide PCB assembly and other related
services which can meet your need at the greatest extent.
Same as any other cheap DIY kit, this one came in a Ziploc bag without any instructions.
However, the component values and polarities are very well denoted on the board.
Inside the Ziploc bag, you'll find 1 LM358 IC, 22 LEDs, 6 resistors, 1 47uF capacitor,
1 push button switch, 1 adjustable tripod, and 1 8050 NPN transistor.
There is no IC base present in this package.
However, I would highly recommend using one for your IC.
To get the fading effect, we need to generate a series of triangular waves.
Because of the triangular waves, the LED starts glowing slowly
and then slowly dims off and the cycle continues.
This setup is done using the LM358 IC. LM358 is a dual operational amplifier IC
integrated with two op-amps powered by a common power supply.
Pin number 1, 2, and 3 are one op-amp channel and pin number 5, 6, 7 are the second op-amp channel.
As the capacitor charges and discharges, the state of the pin number 3 switches from
high to low and based on that the pin number 2 of the op-amp obtains the desired output.
If you want to know more about this IC,
please check out my tutorial number 21 DIY IR Module. The link is in the description below.
So basically, the op-amp here is used for voltage level detection.
In our circuit, we are applying a voltage on the positive pin, pin number 3,
and the voltage to be detected is applied on the negative pin, pin number 2.
The transistor acts as a signal amplifier.
You will need this if you are attaching a cluster of LEDs.
However, just for one LED, you can simply remove it.
Soldering the components to the board was pretty straightforward and relatively trouble-free.
I just had to pay a bit of attention to the direction of the components when soldering
them to the board. I started the project by soldering the IC base to the board
followed by the capacitor, transistor, port, and the push button switch.
Next, I soldered all the resistors to the board.
After that, I soldered all the LEDs to the board.
Due to the repetitive nature of the LED installation, the installation may slightly be
tedious. However, once you finish soldering all the components, I bet you'll feel proud of
yourself. Not to mention, the Ziploc bag contains a few spare LEDs. Hmm, a thoughtful addition.
So this is how it looks like. The effect is a blue heart that increases and decreases
in brightness in a cyclic fashion. The speed can be adjusted using the onboard port.
Now that I have all the electronics bits sorted, it was time for me to add the accessories to it.
Something just clicked in my mind and I went ahead and cut a heart shape
from a piece of pallet plank. I will later stick the circuit board to this heart-shaped
pallet plank. Sanding the plank well and adding a bit of olive oil gave the heart shape a shiny,
nice and smooth texture. For the rest of the project, I'm using a dog made of clay and some
broken pieces of artificial plants. It totally depends on you what you want to add to give your
project a super sexy look. Now to house all the bits and pieces that I gathered so far,
I need to create a base. For that, I'm cutting a 6 inch by 3.5 inch pallet plank. All the bits
and pieces will be glued to this pallet plank. I drilled a hole in the middle of the wooden heart.
Through the hole, I will pass the wire that will power the circuit board. The power supply to the
board is between 4 to 6 volt DC. Any USB interface or three ordinary dry cells can be used to power
this board. Supply voltage to the red LED version is slightly lower than any other colored LEDs.
A 4 volt power supply can power the red version. However, other colors need voltage between 4,
5 and 6 volts. Alright, so now it's just a matter of gluing all the bits and pieces
one by one to the base pallet plank. When you are young and restless, Valentine's Day plays
a significant role in your life. However, if you are deeply in love with someone who
you are going to spend the rest of your life with, every day becomes a Valentine's Day for you.
Thanks again for watching this video. I hope it helps you. If you want to support me,
you can subscribe to my channel and watch my other videos. Thanks. See you again in my next video.
Bye now.