Hi everyone, today I am going to unbox and assemble the Crowbot Bolt an open source programmable Smart Robot Car. CrowBot BOLT is an open source smart programming car powered by ESP32 chip. It has a wealth of sensors (such as a light sensor, ultrasonic sensor, and line Tracking Sensor), comes with Wifi and Bluetooth functions, and can meet a variety of programming environments like Letscode, Micropython, and Arduino. It can quickly realize functions such as light tracking, line tracking, obstacle avoidance, remote control, and light show. As an entry-level STEAM educational robot, the cool and cute BOLT makes robot programming learning and teaching easy and fun.
Intro
This cute little smart car was a birthday gift to my son from elektrao.com.
He was very excited to unbox, assemble and program it using the drag and drop programming
language.
He named it Lily.
You can buy this cute, creative, programmable, multitasking and educational smart robo car
for just 3490 from elektrao.com.
I have provided the link in the description below.
So this is what came inside the mail bag.
I was super excited to open the box and see what's inside.
Crobot has features like infrared light tracking, light following, bluetooth, wifi, buzzer,
ultrasonic obstacle avoidance, programmable IR remote control and double wheel front drive.
The box is very lightweight and contains all the components that you need to create the
robo car.
So this is what was inside the box.
The items on my right are the ones that will assemble into the robo car and the items on
my left will assemble into the programmable remote control.
The only additional item that you need is 6 AAA batteries, 4 for the car and 2 for the
remote.
Everything comes pre-soldered.
All you have to do is spare 30 minutes of your time, sit down and assemble it.
Crobot uses acrylic plate as the shell and the assembly is super simple.
Just align the slots and tighten the screws to complete the build.
Before assembling the components, let's have a quick look at the chassis of the car.
The top side has 2 geared motors, an ESP32 microcontroller, an on and off switch, a reset
button, 2 light sensors, 1 IR receiver for IR remote and 4 female pin headers for the
ultrasonic sensor.
The bottom bit has the omnidirectional wheel, 2 line following sensors, switches to toggle
between Bluetooth and Wi-Fi, USB type C interface for loading programs and 2 I2C interface which
can be connected to 150 plus Crotale modules making it highly scalable.
Alright now let's start putting the bits and pieces together.
I first connected the battery holder to the chassis.
Then I connected the 2 female pin standoff spacers to one side of the side acrylic plate.
Next I slided the chassis into the side plate and attached the front plate to it.
Once I was confident that all the bits are aligned to the correct holes, I attached the
second side plate to the chassis and tightened the screws to complete the setup.
Next I connected the ultrasonic sensor to the female pin headers.
Crobot ultrasonic sensor not only avoids obstacles but also emits colorful RGB light.
Next I connected the 2 wheels to the chassis.
That's it.
All done.
So, as you can see the middle of the front bit has the ultrasonic sensor with 2 light
sensors on both side of it and the IR receiver module just in front of it.
At the back from left to right is the on off switch, the USB C port followed by the 2 buttons
on the right.
Now let's assemble the remote.
Let's first install the button caps.
Different color caps helps in easy identification of the buttons.
The joystick is ergonomically designed to feel comfortable in hand.
The transparent acrylic plate gives you the visibility of the working condition of the
remote.
Next I installed the joystick cap followed by the 2 AAA batteries at the back.
The remote also has a 0.91 OLED display which sits just above the ESP32 microcontroller
to display the current state of the car.
Next I installed the back plate followed by the transparent front plate.
CrowBot can be controlled using Infrared or Bluetooth remote control.
CrowBot can be programmed using Arduino, MicroPython or Let's Code graphical program IDEs.
So this is how it looks like after the assembly.
You can program the remote using USB port present on the remote.
CrowBot comes preloaded with the factory loaded code.
So you can use it as is straight after the assembly.
The IR remote can be used to perform similar functions as the programmable remote or the
joystick.
Have a look at the on-screen buttons to familiarize yourself with the button combinations.
Unlimited creativity is waiting for you to discover.
So what are you waiting for?
Go ahead and order one of your own.