Humidifiers add moisture to the air. They can help people with dry skin, allergies, and respiratory problems. They may also help in preventing influenza and reduce snoring. I bought this AU$2 USB Mini Humidifier DIY Kit from AliExpress and went ahead and created a cute little 3D container for it. In this tutorial, I will show you guys how I designed and assembled the humidifier circuit into the 3D model.
Thanks ------ Thanks again for checking my post. I hope it helps you. If you want to support me subscribe to my YouTube Channel: https://www.youtube.com/user/tarantula3
Humidifiers add moisture to the air. They can help people with dry skin,
allergies and respiratory problems. They may also help in preventing influenza and reduce
snoring. I bought this $2 USB mini humidifier DIY kit and created a cute little 3D container for it.
In this tutorial, I will show you guys how I designed and assembled the humidifier circuit
into the 3D model.
The design was very cute and I went ahead and upsized and customized the design to fit
all my electronic bits into it. With the help of Microsoft 3D Builder,
I modified the 3D model. The model has two compartments. The top compartment is completely
hollow to hold water into it. I kept the top section open to fill water into it.
All the electronic bits will go inside the second compartment.
Those two screw holes are to hold the rechargeable 18650 battery holder.
The pipe-like structure is for the wires to go from the top section to the bottom section.
The top compartment is 9.5 cm by 4.5 cm. So, if we calculate the volume of the cylinder,
it comes out to be 604 cm3. By dividing the volume by 1000, we get the volume of water
that can be stored inside the compartment. So, it comes out roughly around 0.6 liters.
At the back of the model, I created a grove to fit in a block of plastic that will house the
TP4056 18650 battery charging module and a SPDT switch. The charging module gets super hot while
charging. So, I have given enough space in the block to keep the module cool. The bottom lid
will cover and hide all the electronic bits into it. The top lid has a hole in the middle
to house the humidifier straw. That's it. As simple as that.
Once the 3D model was sorted, it was time for me to fire up my 3D printing oven and start printing
these 3D models. As we all know, 3D printing is the process that uses computer-aided design or CAD
to create objects layer by layer. 3D printing is not a new technology. It has been there since
1980s when Charles W. Hull invented the process and created the first 3D printed part. Since then,
the field of 3D printing has grown exponentially and holds countless possibilities. The 3D printing
process fascinates me a lot and I sometimes love to sit near my printer and watch this layer getting
printed. 3D printing is a highly addictive hobby. There are so many things you can do using a 3D
printer. From designing 3D models to printing them using a 3D printer has now become my new hobby.
I have been a maker since I was 10 years old and have always constructed and made my own stuff. 3D
printing for me is a blessing. I am totally lost in the 3D printing heaven. 3D printing has changed
my electronic workshop life forever. Before when I used to order parts, I always used to wonder if
the part would fit in my project resource. But after I got my 3D printer, it doesn't matter at
all. Because if it doesn't fit, I could design and print it myself. The 3D printer was definitely
the missing part from my electronic workshop. The entire printing process took roughly around 20
hours. After extracting all the 3D printed bits, I sanded them to give them a nice and smooth
texture. This is the bottom cover. That's the top lid with a hole for the humidifier straw
and a handle to open and close the lid. This block will hold the battery charger and the
switch into it. The main body has the top compartment for holding water in it and the
bottom compartment for housing all the electronic bits into it. The circuit is very simple. By
connecting a USB type C charging cable to the TP4056 module, we charge the 18650 battery connected
to the B plus and B minus terminal of the module. The humidifier module connects to the out plus and
out minus terminal of the charging module via a SPDT switch. Using this switch, we can turn on or
off the humidifier. So these are the components that were in the DIY kit. A circular atomizer,
two plastic holders, a straw and the main humidifier circuit board. I customized the
board by adding a couple of male pin headers to power this unit using a battery and dropped a
blob of soda to bypass the push button switch. To assemble, insert the atomizer into the black
plastic holders along with the humidifier straw. Then connect the atomizer to the humidifier circuit
board. In my project, the circular atomizer will be way far from the circuit board. So, I will
replace the short red and black cable with a long ribbon cable. Let's start by soldering the battery
holder to the B plus and B minus terminal of the charging module. Then let's solder the negative
connector that will power the humidifier to the out minus terminal of the board. After that, let's
solder a loose cable to the out plus terminal. Now, let's slide in the humidifier's positive
connector and the other end of the loose cable through the plastic block. Then let's solder
these two cables to the SPDT switch and superglue it to the block. Then push the charging module
into the grove of the plastic block. Once the block is all set, push it into the backside of
the main unit. After that, using couple of screws, attach the battery holder to the bottom of the
unit. I used hot glue to stick the humidifier circuit to the bottom of the unit. Once everything
is in place, plug in the 18650 battery to the battery holder and push the black and white
atomizer cable through the pipe-like structure. After that, connect the atomizer's power cord to
the humidifier and seal the bottom lid. Be very careful while assembling the top. The atomizer
has two sides. The one with the more exposed metal area touches the humidifier straw. I soldered the
atomizer to the white and black cable after passing it through the top lid's hole. Then, it was just a
matter of putting the atomizer inside the two black holders along with the straw and then snap
closing it and pushing the setup through the hole. That's it. All done. I wasn't very confident about
PLA being waterproof and not absorbing water, leading to swelling and degrading of the
biodegradable plastic. So, I went ahead and painted the inner bit with bitumen waterproofing membrane.
Then, using acrylic colors, I painted the body of the 3D printed model. I gave the model a bit
rustic look. But hey, it totally depends on you how you want your project to look like.
Once fully charged, the unit can run seamlessly for roughly around 10 hours. To fill the container
with water, you just need to lift the top lid and pour water into it. Humidifiers add moisture to
the air. They can help people with dry skin, allergies, and respiratory problems. They may
also help in preventing influenza and reduce snoring. I bought this $2 USB mini humidified DIY
kit and created a cute little 3D container for it. So, this is how my final setup looks like. Do
comment and let me know if there are any scopes of improvement. Thanks again for watching this
video. I hope it helps you. If you want to support me, you can subscribe to my channel
and watch my other videos. Thanks. See you again in my next video. Bye now.