In this video i will show you how to use a test orint to adjust your flow rate on your ender 3 or ender 3 pro. this also works for other printers too! we will be adjusting the flow setting in cura under filament settings, to get the exact width we are trying to print, increasing precision by using the proper flow rate!
If you cant afford a donation, thats ok. leave a couple likes. and dont forget to subscribe. sharing and liking our videos is one of the best ways to help support the channel. other ways to contribute: if you shop on amazon, bookmark this link and use it, it costs you nothing, and helps me out a ton! https://www.amazon.com/?rw_useCurrent...
if you can afford a donation, please contribute! a little goes a long way! thanks again for all the support people! I couldnt do it without you!
Disclaimer: ANY AND ALL reviews are my own, honest opinion, and I do not accept payment in exchange for a favorable review. for more information on where to send your tech to be reviewed, e-mail me at [email protected] Subject:TECH
Current Channel Goal: 1000 Subs!
Want to send me something? Technivorous 902 n Hughes Blunt Sd 57522
now accepting reviews! sorry we DO NOT take payment for better reviews.
AI Generated·May contain errors
Video Summary
AI Generated
This video provides a practical guide on how to calibrate and adjust the flow rate of a 3D printer to ensure accurate extrusion widths. By printing a simple calibration wall and using a specific mathematical formula, users can fine-tune their material settings to achieve precise print quality.
Hey guys, Techniverse here.
Quick side note, happy birthday to me.
Today we're going to be adjusting our flow rate.
So in order to do that, we're going to need a simple model.
This is a 0.4 millimeter wall.
You can get these by just typing in calibration on Thingiverse.
We're going for the 0.4 millimeter because we're going to be measuring the difference.
So you need to make sure in quality that our line width is also set to 0.4 millimeter.
I'm just going to put a single perimeter down.
We're going to measure that it's extruding the right width.
So I'm going to go ahead and print this.
All right, so we have our perimeter wall here and it's supposed to be 0.4 millimeters.
Let's check it here and it looks like we're pretty spot on 0.4 millimeters.
We're a little bit low.
I don't have a digital pair of calipers on me so I can't get the exact reading.
If you have a digital pair, definitely use those because they'll give you a more accurate reading.
From here, we need to go back to the computer.
I don't need to make an adjustment to my flow rate because I have the right size.
It's 0.4 millimeters so it's accurate,
but I'll show you how to adjust yours if yours doesn't come out right.
All right, so what we need to do is some simple math.
We're basically going to use the same equation that we used for calculating our e-steps.
What we're going to do is we're going to take the amount that we wanted to measure,
which was 0.4, and we're going to divide it by the amount that we did get.
I'm going to say in this case 0.38 because I know I'm not exactly on 0.4,
but you want to use your actual measurement for the second perimeter and hit equals.
Basically, you have this result here and what you're going to want to do is multiply that
by what your flow rate already is, so times 100, and that puts me at 105.26.
I'm going to want to go in here and adjust my flow rate.
It is going to be in the material and it looks like that's what we need to do.
We're going to go ahead and slice it again, reprint it, and see if it comes out more accurate.
Since mine was pretty spot on, I'm not going to print it again,
but feel free to do it a couple of times, double check, make sure that everything's
working properly, and then you might adjust this up and down after doing it two or three times.
The law of averages says that you're going to want to do this three times
just to get an average baseline or a median, which would be a good point to work from moving
forward. That's pretty much it for calculating the flow rate, and we'll see you guys in the next
video. As always, guys, I am Techniverous. Thanks for watching this video. Don't forget to hit the
like button. You can subscribe right here by clicking on the icon. I put a couple of videos
up in the corner. One of them is going to be my latest video, my latest upload, and the other
one is going to be what YouTube recommends for you, so feel free to check those out. Don't forget
to hit that bell for notifications down below, and we'll see you guys next time.