Cura settings in 5 minutes or less! - 1.2 Line Width

Technivorous 3d Printing
33 followers
1 Video View·Sep 2, 2026
Similar to layer height, line width is another extrusion parameter, except this is the width of extrusion on the horizontal. More detail in the video on what your looking for here.
Hi folks, TechNiverse here. Welcome to my Kira playlist.
Before we get started, hit that subscribe button so you can find your way back here.
I update often. That said, as you may have noticed, Kira settings can be very simple
or very in-depth. So I took the time to make a video about each section in the custom settings
menu, and I'm going to quickly go over the important settings each section contains
and briefly explain them. Are you ready? Good, let's go. This is Kira settings in five minutes
Okay, so the next setting we're going to discuss is going to be line width. So we covered initial
layer height basically at the same time as layer height, and we're going to cover all the settings
that are indented in below line width, with line width, as well as the initial line width. Now
you'll notice down here the initial line width itself is actually listed in a percentage, which
is interesting. You can increase or decrease that percentage to widen or thin out the line a little
bit. Now when the initial line becomes too thick, they start to cross over each other too much and
you get a raised bump through your print where the nozzle travels. Where the initial layer line
height or width is too thin, the lines don't make contact and you end up with a separated first
layer. Now these problems normally correct themselves as you travel up, but what happens
is you're actually putting down an unstable base and you're not extruding the proper amount of
filament. So what you want is to ensure that the layer line width, or excuse me the initial line
width, is putting down just enough filament to give you a smooth sheet. It should be seamless
without any raises or pits in it and that is a little bit difficult to achieve at first. Once
you get used to dialing in the settings and leveling your bed out to where it needs to be,
it becomes second nature and rather simple. Now you can see I can also increase my line width,
but I can't print wider than the nozzle itself. This seems like a misnomer and it kind of is. You
can increase past the nozzle width by a small percentage, but if you decrease, and it says
right here, slightly reducing this value could produce better prints. So if I'm using a 0.4
millimeter nozzle, the ideal thing to shoot for would be about 0.38 to 0.39 millimeter line width
because that's slightly under the width of the nozzle and therefore easier to extrude because
you have to remember as it's dragging, especially that first layer, it's smashing it down into the
bed as well and it's going to widen out a little bit. So this is the real thing to play with in
order to get that first layer smooth and get the glass sheet-like appearance by using the
line width and the initial layer line width adjustments. Very very handy and let's take a look
at, let's say we had a larger nozzle on here, 0.6. We'll slice this and check out the noticeable
difference between the layer height and the line width down on the first layer. It shouldn't be
exactly round. Let's see, we'll zoom down here. Let's see, maybe, there we go. Now you can see
that the lines are wider than they are tall. That is because they are 0.6 millimeters wide.
The slicer will do that regardless of your nozzle width. Whether or not the print will actually work
is another story. So you need to keep in mind your nozzle width when working with the line width
and general rule of thumb is increasing the layer line width will increase adhesion but it can also
lead to overextruding and decreasing the line width will decrease extrusion which won't generally
lead to underextrusion but it will lead to an underformed bottom layer which is never a good
thing. So as always this channel is brought to you by these fine Patreon supporters. If you'd
like to support the channel on Patreon head over to www.patreon.com slash Technivorous.
That's going to be it for this video. As always I am Technivorous and thanks for watching. Don't
forget to check out our main channel page where we do a free giveaway for our subscribers every
month. So far we've given away things like a Capricorn PTFE tubing kit and spools of filament.
So the giveaway videos are always pinned to our main channel page. So all you have to do is
subscribe and leave a comment on the giveaway video for the current contest. Feel free to check
out this video right here. YouTube picked it for my content just for you and if you haven't already
you can hit the subscribe button right here. So what are you waiting for? Become a Technivore now.
Thanks again. Technivorous out.
