anyone who uses a 3d printer is probably familiar with this sensor, its a thermister for arduino and it takes the teemperature of things. get a simple surrounding temp reading with the code included in this video!
Like and Subscribe!
Affiliate links for arduino sensors! Large Arduino Kit (Recommended) includes various sensors, a couple breadboards, loose components, pcb board, jumper wires, soldering iron AND more: https://www.banggood.com/custlink/mmKhdf9Si8
Want to send me something? Technivorous 902 n Hughes Blunt Sd 57522
AI Generated·May contain errors
All right folks, welcome to Arduino for Beginners. This is Arduino 101.
And the topic of today is thermistors. So I have one here, it is hooked up already.
I will show you the very simple setup. The three output pegs, pins, excuse me,
on the thermistor are located on the edge of the board and they are labeled negative
and S for signal. So from that, we can deduce that the negative will go to the negative on
either the Arduino or the breadboard that you're using. In this case, it's breadboard. And then
the peg in between them is going to be positive. So you can go ahead and run that to the positive
on the breadboard. The last one is the signal. And we are going to put that into our Arduino
and use the code that you see on the screen to run it. And I will give you just a second to
pause the video and go ahead and get this all typed up here. There's not much left down at
the bottom other than one delay of a half a second there. So let's go ahead and pause the video,
get this typed in. It will take you a minute. These variables are what's going to convert our
temperature into readable temperature. So, and then we'll just print it here. So nothing you
really haven't seen before. Just go ahead and grab the code. And when you're done, hit play.
And now that you're ready to move on, I'm going to go ahead and show you what this code does.
So I'm holding the sensor here and the actual sensor itself is really tiny. It's that little
black knob on the tip of these two wires. So what we're going to do is upload the sketch,
get it running, and then we will open the serial monitor and see what we're getting for temperature
readings. I believe the math that we've chosen is going to give us Fahrenheit readings. So let's
see. Yeah, I'd say that's pretty close. So we're getting a temperature reading of about 68.9, 69,
still ranging upward a little bit. Depending on where I move it, it will alter it even more.
And I can put my hand over it or breathe on it and it'll take different adjustments that way as
well. I just realized you can't see this. There it is. So this is our temperature reading.
Everything's coming out nominally. I mean, it's pretty much giving us an accurate reading.
And you can see this guy right here, just this tiny little blob right here,
that's what's doing the actual reading. So this is a fairly simple and straightforward tutorial.
It doesn't take much. You can use this for a ton of other things if you don't need that bulky
humidity sensor. In particular, these are used in the hot ends of 3D printers. So knowing how
to just plug one in and get a reading from it is kind of cool, seeing as how it's part of the
inner workings of the software that runs 3D printing as well. Generally Marlin or Rapidi
or whatever 3D printing host you have on there will run the actual thermistors and the motors
and all of that. So it's nice to know how it works outside of the context that I normally see it in
or that you might normally see it in here on the channel. Well, that's it guys. That's going to wrap
up this video. If you've noticed the shirt, the merch is available. Go ahead and check out the
Teespring merch link down below. It won't be available on a channel store until I reach 10,000
subscribers and so far I am just about to hit 5,000. So it'll be a little while, a couple more
months before you see this on the actual channel, but they are available now. I have a couple other
designs. Feel free to pop over there and check them out and know that any purchase through the
Teespring site definitely helps to promote our site here and increase the channel's ability
to make videos in the future. So we appreciate all your support. Don't forget to check out
the Teespring link. Check out our Patreon link. Leave a like on this video and hit that subscribe
button because we have a lot more coming at you in the coming days.